Manual Smartinterface Stinger/Spyder
Transcrição
Manual Smartinterface Stinger/Spyder
Instruction Manual to install the USB Smartinterface for Stinger and Spyder dive computers USB Smartinterface – Installation for Stinger and Spyder dive computers Unfortunately Suunto no longer supports Stinger and Spyder dive computers with their free of charge software Dive Manager. The Stinger can be read out with the Dive Manager up to revision 3.1.0. (download here), the Spyder unfortunately only up to revision 1.6 (download here). This reference table will give you an overview of software to use to read out your Stinger/Spyder. (go to reference table) After connecting the interface with your PC, Windows automatically installs a driver. There‘s no other customisation necessary for the Dive Manager 1.6 and you can directly proceed with this manual. Unfortunately the Dive Manager 3.1.0 requests a driver beginning with the name Suunto. See universal manual for the necessary adaption. Rev. 1.0 www.smartinterface.de · [email protected] 1 Manual to install USB Smartinterface for Stinger and Spyder Dive Computers 1.0 Connect the interface with your PC (possibly after the driver installation). Start the Dive Manager and set up a new profile under the „File“ tab. Rev. 1.0 a Dive Manager 1.6 b Dive Manager 3.1.0 2a Select the respective port and dive computer type. 2b In the Dive Manager 3.1.0 start the download wizard and then select port and dive computer type. www.smartinterface.de · [email protected] 2 Manual to install USB Smartinterface for Stinger and Spyder Dive Computers 3.1 a/b Insert dive computer into the interface and … 3.2 a/b … switch to transfer mode. Rev. 1.0 www.smartinterface.de · [email protected] 3 Manual to install USB Smartinterface for Stinger and Spyder Dive Computers 4.1 a/b Press the upper right button (Dive) until … 4.2 a/b … „MEM“ appears in the display. Then press the upper left button (TIME) … 4.3 a/b … until „TR-PC“ appears. 4.4 a/b The dive computer is now in transfer mode and you can start the transfer in the Dive Manager. Please note: If the dive computer‘s data contact gets in touch with the housing or the transfer is interrupted, you‘ll need to set the dive computer to the transfer mode again before you can start with a new readout. (Repeatedly press the upper left button until TR-PC appears.) Rev. 1.0 www.smartinterface.de · [email protected] 4 Manual to install USB Smartinterface for Stinger and Spyder Dive Computers 5.0 a/b The transfer begins. a Dive Manager 1.6 b Dive Manager 3.1.0 6a After a successful transfer the data will show in the data base. 6b After a successful transfer set the mark in the check box to transfer all dives and follow all further instructions. Rev. 1.0 www.smartinterface.de · [email protected] 5 Manual to install USB Smartinterface for Stinger and Spyder Dive Computers a Dive Manager 1.6 b Dive Manager 3.1.0 7a All data is now available for further processing. 7b The dives will be listed in the data base and are now available for further processing. Please note: You can slightly resize the window by drawing at the lower edge. If problems occur while reading out the dive computer, we recommend to use this test tool for the problem analysis. (http://www.smartinterface.de/downloads/TestTool.zip) Rev. 1.0 www.smartinterface.de · [email protected] 6 Content 1.0 Connect the interface with your PC (possibly after the driver installation). Start the Dive Manager and set up a new profile under the „File“ tab. 2a Select the respective port and dive computer type. 2 2 2b In the Dive Manager 3.1.0 start the download wizard and then select port and dive computer type. 2 3.1 Insert dive computer into the interface and … 3 3.2 … switch to transfer mode. 3 4.1 Press the upper right button (Dive) until … 4 4.2 … „MEM“ appears in the display. Then press the upper left button (TIME) … 4 4.3 … until „TR-PC“ appears. 4 4.4 The dive computer is now in transfer mode and you can start the transfer in the Dive Manager. 5.0 The transfer begins. 4 5 6b After a successful transfer set the mark in the check box to transfer all dives and follow all further instructions. 5 6a After a successful transfer the data will show in the data base. 5 7a All data is now available for further processing. 6 7b The dives will be listed in the data base and are now available for further processing. 6 Rev. 1.0 www.smartinterface.de · [email protected] 7 Imprint Technisches Büro Kühnhold Ehestorfer Weg 155 21075 Hamburg http://www.smartinterface.de · [email protected] Copyright All images and text in this instruction manual, as well as the instruction manual itself are copyright protected, any further use must be approved in writing by www.smartinterface.de. Copyright and labelingt All brands and trademarks specified within the description and, where applicable, protected by a third party are subject without restriction to the terms and conditions of the respectively valid right to use a symbol and the ownership rights of each registered owner. The mere mention thereof shall not be construed to represent that the trademarks are not protected by third party rights! The brand names and trademarks used in this documentation are the property of the respective rights owners and are used here only for descriptive purposes. Disclaimers The devices, tools and interfaces were thoroughly tested prior to the delivery. Connection, use and operation shall be at your own risk. No liability shall be assumed for damage or loss of data or lack of waterproofness. Recycling European Union – Disposal information: This symbol indicates that this product must be disposed of pursuant the valid legal provisions and separated from domestic waste. Bring this product to an official collection point for disposal. Products can be brought to some collection points for disposal free of charge. Separate collection and recycling conserves raw material reserves and ensures compliance with all regulations for the protection of health and the environment when recycling the product. WEEE-Reg.-Nr. DE82497460 Rev. 1.0 www.smartinterface.de · [email protected] 8