Montageanleitung
Transcrição
Montageanleitung
Montageanleitung Assembly instructions Abt Frontgrill Emblem Art.-Nr.: ZB 000 031 Abt front grille emblem Order no.: ZB 000 031 Montageanleitung für Abt Frontgrill Emblem Montiertes Abt Frontgrill Emblem am Beispiel eines Audi A4 Lieferumfang: Menge 1 1 1 2 1 04.07.12 / AF Bezeichnung Emblem Frontplatte Gegenplatte Kabelbinder 3,6x280mm (1x Ersatz) Montageanleitung MA_Frontgrill-Emblem_ZB000031 Seite 2 von 12 Montageanleitung Montagezeit: ca. 0,25h Achtung: Lesen Sie diese Montageanleitung vor der Montage sorgfältig und vollständig durch! Sie enthält wichtige Hinweise und Informationen, die unbedingt vor und während der Montage beachtet werden müssen und hilft, Missverständnisse zu vermeiden. Bitte wenden Sie sich im Zweifelsfalle an unseren technischen Kundendienst (+49 (0)831 57140-905). 1. Überprüfen Sie die Ware vor der Montage auf Unversehrtheit und mit Hilfe der Stückliste auf Vollzähligkeit. 2. Stecken Sie nun den Kabelbinder durch die Führungen auf der Rückseite der Abt Frontplatte hindurch (Abb.1 und Abb.2). Hinweis: Achten Sie darauf, dass der Verschluss des Kabelbinders in die dafür vorgesehene Aussparung einrastet (Abb.3 und Abb.4). Abb.1 und Abb.2: Einführen des Kabelbinders Abb.3 und Abb.4: Eingerasteter Kabelbinder 3. Legen Sie die Größe der Gegenplatte fest. Diese wurde größer ausgelegt, um auch bei einem großen Abstand der Frontgrillstreben einen festen Halt des Frontgrillemblems zu gewährleisten. Um einen optimalen optischen Eindruck zu erzielen, können Sie die Gegenplatte bei geringem Abstand der Gitterstreben durch Beschneiden mit geeigneten Werkstattmitteln verkleinern. Hinweis: Um die Wirksamkeit der Gegenplatte zu gewährleisten, muss diese grundsätzlich größer als der Abstand der Frontgrillstreben sein. 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 3 von 12 4. Führen Sie nun den Kabelbinder durch die Gegenplatte hindurch (Abb.5). Bitte beachten Sie dabei, dass die abgerundeten Kanten der Gegenplatte im montierten Zustand auf der Seite des Kabelbinders (hinten) liegen sollten. (Abb.6). Abgerundete Kanten Abb.5 und Abb.6: Durch Gegenplatte durchgesteckter Kabelbinder 5. Schieben Sie nun, wie in Abb.7 ersichtlich, die Gegenplatte zwischen den Frontgrillstreben hindurch und bringen Sie diese mit Hilfe des Kabelbinders in eine vertikale Position. Hinweis: Durch leichten Zug am Kabelbinder können Sie anschließend die Gegenplatte in dieser Position halten. Abb.7: Einschieben des Frontgrill Emblems 6. Stecken Sie nun das Ende des Kabelbinders durch dessen Verschluss (Abb.8; Seite 6) und ziehen Sie Ihn soweit an, bis die Frontplatte auf der Vorderseite der Frontgrillstreben leicht anliegt. Achtung: Ziehen den Kabelbinder dabei noch nicht endgültig fest, um ggf. die Position der Frontund Gegenplatte nochmals korrigieren zu können. 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 4 von 12 Abb.8: Befestigen des Frontgrill Emblems 7. Wenn sich die Front- und Gegenplatte in der gewünschten Position befinden, ziehen Sie den Kabelbinder endgültig fest. 8. Schneiden Sie den überstehenden Teil des Kabelbinders mit einem geeigneten Werkstattmittel, z.B. einem Seitenschneider, bündig mit der Abt Frontplatte ab (Abb.9). Um eine möglichst ebene Klebefläche zu erhalten, schneiden Sie ggf. den Kabelbinder nochmals vorsichtig mit einem Teppichmesser nach (Abb.10). Abb.9 und Abb.10: Abtrennen des Kabelbinders 9. Entfernen Sie nun die Abdeckung der Klebefläche auf der Rückseite des Abt Emblems und kleben Sie dieses abschließend auf die dafür vorgesehene Frontplatte (Abb.11; Seite 7). 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 5 von 12 Abb.11: Montiertes Frontgrill Emblem 10. Rechtlicher Hinweis: Abt Sportsline haftet nicht für Schäden aller Art, die durch eine unsachgemäße Montage und/oder durch eine unsachgemäße Handhabung des Abt Frontgrill Emblems sowie des mitgelieferten oder des empfohlenen Montagematerials entstehen. Druckfehler und technische Änderungen / Neuerungen vorbehalten! 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 6 von 12 Assembly instructions for the Abt front grille emblem Abt front grille emblem mounted e.g. on an Audi A4 Scope of delivery: Quantity 1 1 1 2 1 04.07.12 / AF Description emblem front plate counter plate cable tie 3,6x280mm (1x replacement) assembly instructions MA_Frontgrill-Emblem_ZB000031 Seite 7 von 12 Assembly instructions Assembly time: approx.: 0,25h Attention: Please read the assembly instructions carefully and completely before installing! It includes important details and information which must be followed before and during the installation and which help to avoid misunderstandings. In case of doubt, please feel free to contact our technical service at (+49 (0)831 57140-905). 1. Check if the parts are undamaged and the delivery is complete by means of the parts list before installing. 2. Insert the cable tie through the guides on the backside of the Abt front plate (fig.1 and fig.2). Note: Make certain that the fastener of the cable tie latches into the intended opening (fig.3 and fig.4). Fig.1 and fig.2: Insertion of the cable tie Fig.3 and fig.4: Latched in cable tie 3. Determine the size of the counter plate. It is dimensioned larger to guarantee a good hold of the Abt front grille emblem, even when there is a large interspace between the front grille struts. If there is little interspace between the grille struts, you can trim the counter plate with appropriate instruments to get an optimal optical impression. Note: To assure the effectiveness of the counter plate, the counter plate has to be larger than the interspace of the front grille struts. 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 8 von 12 4. Now put the cable tie through the counter plate (fig.5). Please note that the round edges of the counter plate should be on the side of the cable tie (back) when it is mounted (fig.6). round edges Fig.5 and fig.6: Cable tie inserted through the counter plate 5. Push the counter plate through the front grille struts (fig.7) and bring it into a vertical position by means of the cable tie. Note: By pulling the cable tie slightly, you are able to keep the counter plate in this position afterwards. Fig.7: Insertion of the Abt front grille emblem 6. Now push the end of the cable tie through its fastener (fig.8; page 12) and pull it tight only until the front plate slightly abuts the front side of the front grille struts. Attention: Do not tighten the cable tie finally to be able to probably adjust again the position of the front and counter plate. 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 9 von 12 Fig.8: Fastening of the front grille emblem 7. If the front and counter plate are in the desired position, pull finally the cable tie tight. 8. Trim the overlapping part of the cable tie with appropriate instruments, e.g. a side cutting pliers, flush to the Abt front plate (fig.9). To maintain the adherent surface as even as possible, probably trim again the cable tie carefully with a carpet cutter (fig.10). Fig.9 and fig.10: Cutting of the cable tie 9. Now remove the adherent surface covering on the back side of the Abt emblem and adhere it onto the intended front plate (fig.11; page 13). 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 10 von 12 Fig.11: Mounted Abt front grille emblem 10. Legal hint: Abt Sportsline is not liable for damages of all kinds resulting from faulty assembling and/or from mishandling of the Abt front grille emblem as well as of the provided or recommended installation material. Printing errors and technical alterations / news excepted! 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 11 von 12 Abt Sportsline GmbH Daimlerstraße 2 87437 Kempten / Allgäu www.Abt-sportsline.de 04.07.12 / AF MA_Frontgrill-Emblem_ZB000031 Seite 12 von 12