MZF-55.. - Monacor
Transcrição
MZF-55.. - Monacor
Stage Line MZF-55.. R Flight Case Serie Montageanleitung Bevor Sie beginnen ... Wir wünschen Ihnen viel Spaß mit Ihrem neuen img Stage Line Selbstbausatz für ein Flight Case. Für eine einfache Montage beachten Sie bitte sämtliche Hinweise in dieser Montageanleitung und gehen in der angegebenen Reihenfolge vor. Der Bausatz enthält alle benötigten Bauteile. Diese sind bereits auf das richtige Maß zugeschnitten. 1 Zum Zusammenbau werden benötigt: • • • • • • • Blindnietenzange Bohrmaschine Spiralbohrer (1,5 mm, 4,3 mm, 5,2 mm, 6,0 mm) Hammer Metallfeile Zollstock oder Bandmaß Holzleim 2 Holzplatten 1) Um zu sehen, wie die Platten richtig zusammengesetzt werden und welche Kanten verleimt werden müssen, zuerst alle Holzplatten provisorisch zurechtlegen. 2) Den Boden mit den entsprechenden Seitenteilen und den Deckel mit den dazugehörigen Seitenteilen verbinden. Dazu 1,5 mm-Löcher für die Nägel vorbohren. Die Platten verleimen und zusammennageln. Den Leim trocknen lassen. 3) Eventuelle Zwischenfächer festleimen. Keine Nägel verwenden, da diese nicht durch Profilleisten abgedeckt werden. Zur Feststellung der richtigen Montageposition eventuell die zugeschnittenen Schaumstoffpolster zu Hilfe nehmen. 3 Winkelprofilleisten für Boden und Deckel 1) Die Winkelprofilleisten (1) auf die Kanten des Bodens und des Deckels mittig anlegen. Rechts und links muß gleichviel Platz zu den Ecken bleiben. Hier werden später die seitlichen Winkelprofilleisten (2) zwischengesetzt. 2) Die Löcher der Winkel auf den Holzteilen anzeichnen. 3) 4,3 mm-Löcher bohren. Die Winkel mit den dünnen Blindnieten befestigen. Für eine saubere Vernietung muß immer ein ausreichender, gleichmäßiger Druck auf die Blindnietenzange ausgeübt werden. 2 1 2 Stage Line MZF-55.. R Flight Case Serie 4 Schließprofile und Winkelprofilleisten für die Seitenteile Die Schließprofile werden auf die Stoßkanten von Deckel und Bodenteil angebracht. Sie sind mit 45° abgewinkelt und bestehen aus einem männlichen Teil (4) für den Boden und einem weiblichen Teil (3) für den Deckel. Wenn für das Flight Case Einbau-Verschlüsse und Einbau-Scharniere verwendet werden, sind die entsprechenden Schließprofile an der Seite, wo der Verschluß und das Scharnier später montiert wird, gerade abgesägt. Achten Sie darauf, daß diese Schließprofile an den Stellen montiert werden, wo sich später der Verschluß bzw. das Scharnier befindet. 3 4 1) Die Ecken der Schließprofile mit einer Metallfeile entgraten. 2) Die Schließprofile auf die Kanten legen. Die Befestigung erfolgt durch die beiliegenden Winkel (5). Diese Befestigungswinkel auf die Schließprofile legen, und die Befestigungslöcher anzeichnen. 5 5 3) Nur durch den äußeren Schenkel des Schließprofils und durch das Holz 4,3 mm-Löcher bohren. So bleiben die Innenseiten der Schließprofile glatt. 4) Die seitlichen Winkelprofilleisten (2) anlegen. 5) Mit den dünnen Blindnieten die Befestigungswinkel und damit gleichzeitig die Schließprofile festnieten. 6) Eventuell die seitlichen Winkelprofilleisten (2) ebenfalls vernieten. Bei Gehäusen mit einer geringen Höhe werden diese Winkelprofilleisten nur durch die Befestigungswinkel (5) und der anschließenden Montage der Kugelecken gehalten. 5 Kugelecken 1) Die Kugelecken auf je eine Gehäuseecke legen. Die Löcher anzeichnen. 2) 5,2 mm-Löcher bohren. 3) Die Kugelecken mit den dickeren Blindnieten befestigen. Für eine feste Verbindung beim Nieten die Ecken gut andrücken. 6 Verschlüsse und Scharniere Je nach Flight Case Modell sind die Verschlüsse und Scharniere zum Aufsetzen (Aufbau) oder zum versenkten Einbau vorhanden. Die Flight Cases für 19”-Geräte sind mit zwei abnehmbaren Deckeln ausgestattet. Diese müssen gegeneinander austauschbar sein. Hier zuerst Verschluß und Scharniere an einer Seite des Flight Case' und an einem Deckel montieren. Danach Verschluß und Scharniere auf der zweiten Seite des Flight Case' ebenfalls paßgenau für den ersten Deckel anbringen. Zuletzt Verschluß und Scharniere paßgenau am zweiten Deckel festnieten. 2 2 Stage Line MZF-55.. R 6.1 Aufbau-Verschluß und AufbauScharniere Der Verschluß und die Scharniere bestehen aus zwei Teilen, jedoch nicht das 90°-Stoppscharnier bei einigen Modellen. 1) Das kleinere Teil (6) vom Verschluß bzw. vom Scharnier immer am Deckel befestigen. 2) Die Löcher (4,3 mm) für die Nieten nur durch die äußeren Schenkel der Schließprofile und durch das Holz bohren. So bleiben die Innenseiten der Schließprofile glatt. 3) Alle Teile mit den dünnen Blindnieten befestigen. 6.2 Einbau-Verschluß und EinbauScharniere Der Verschluß und die Scharniere werden in die Aussparungen von Deckel und Gehäuse eingesetzt. 1) Die Löcher (5,2 mm) für die Nieten nur durch die äußeren Schenkel der Schließprofile und durch das Holz bohren. So bleiben die Innenseiten der Schließprofile glatt. 2) Den Verschluß mit den dickeren Blindnieten befestigen. 3) Die Scharniere nach der Abbildung zusammensetzen und mit den dickeren Blindnieten montieren. 7 Griffe Je nach Flight Case Modell werden die Griffe auf das Gehäuse geschraubt (Aufbau) oder versenkt festgenietet (Einbau). 7.1 Aufbau-Griffe 1) 5,2 mm-Befestigungslöcher bohren. 2) Den Griff mit der beiligenden Befestigung sowie den M5-Schrauben, Scheiben und Muttern montieren. 3) Zum Schluß die Kunststoffkappen auf die Griffbefestigung stecken. 7.2 Einbau-Griffe 1) Die Einbau-Griffe in die seitlichen Aussparungen des Gehäuses einsetzen. 2) Die Befestigungslöcher anzeichnen. 3) 4,3 mm-Löcher bohren, und die Griffe mit den dünnen Blindnieten befestigen. Je nach Flight Case Modell sind verschiedene Zusatzteile zu montieren: Flight Case Serie 6 Stage Line MZF-55.. R Flight Case Serie 8 Befestigungsschienen für 19"-Geräte Die Schienen werden gleich hinter dem Schließprofil montiert. 1) 6 mm-Befestigungslöcher bohren. 2) Die beiliegenden Käfigmuttern vor der Befestigung in die Schienen einschieben. Pro Höheneinheit werden 2 Muttern auf jeder Seite benötigt (z. B. bei 4 HE = 8 Muttern pro Schiene). 3) Die Schienen mit den beiliegenden Schrauben (M6 x 25 mm) befestigen. 9 Füße Bei Bedarf das Flight Case mit Füßen versehen. 10 Schaumstoff Alle Schaumstoffteile sind selbstklebend. 1) Zuerst alle langen Seitenteile bekleben. 2) Danach alle kurzen Seitenteile auspolstern. 3) Zum Schluß die Boden- und Deckelflächen auskleiden. 11 Technische Daten Modell MZF-5501 MZF-5504 MZF-5506 MZF-5507 MZF-5509 MZF-5510 MZF-5511 MZF-5512 MZF-5513 MZF-5514 Bestell-Nr. 24.5240 24.5250 24.5260 24.5320 24.5330 24.5270 24.5340 24.5350 24.5280 24.5360 Verwendung 8 Micros 160 CDs Keyboard Keyboard Guitar Bass Guitar Universal Universal Universal Universal Innenmaß (B x H x T) 550 x 350 x 87 mm 550 x 400 x 158 mm 1132 x 412 x 175 mm 1232 x 452 x 185 mm 1102 x 402 x 87 mm 1252 x 452 x 87 mm 600 x 400 x 210 mm 800 x 500 x 472 mm 1000 x 400 x 372 mm 1200 x 500 x 472 mm Gewicht 4,3 kg 6,5 kg 10,5 kg 11,5 kg 8,1 kg 10,5 kg 6,8 kg 17,0 kg 18,0 kg 23,5 kg Modell Bestell-Nr. Höhe HE* Innenmaß (B x H) MZF-5521 MZF-5522 MZF-5523 MZF-5524 MZF-5525 MZF-5526 MZF-5527 MZF-5528 24.5290 24.5370 24.5300 24.5380 24.5310 24.5390 24.5400 24.5410 Innenmaß Tiefe (Front-/Mittel-/Rückteil) 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 19"-Racks 2 4 6 8 10 12 14 16 513 x 114 mm 513 x 203 mm 513 x 292 mm 513 x 381 mm 513 x 470 mm 513 x 559 mm 513 x 648 mm 513 x 737 mm *1 HE = 44,45 mm Laut Angaben des Herstellers. Änderungen vorbehalten. Gewicht 8,9 kg 11,1 kg 12,0 kg 14,0 kg 14,0 kg 16,5 kg 19,5 kg 21,5 kg Stage Line MZF-55.. R Flight Case Series Instruction Manual Before you start . . . We wish you much pleasure with your new img Stage Line flight case rack kit. For an easy assembly please follow all instructions of this manual and pay attention to the order of instructions. This kit includes all necessary components which are already cut to the correct sizes. 1 The following tools are required for assembly: • • • • • • • Rivet tool Drilling machine Twist drill (1.5 mm, 4.3 mm, 5.2 mm, 6.0 mm) Hammer Metal file Yardstick or tape rule Wood glue 2 Wood Panels 1) Position all wood panels in such a way so that you can see how they have to be fitted and which edges have to be glued. 2) Mount the corresponding side panels to the bottom and to the cover by pre-drilling 1.5 mm holes for the nails. Glue the panels together and insert the nails. Let the glue dry. 3) If desired, glue-on compartments. Do not use any nails since they will not be covered by the profile edges. In order to find out the best mounting position you can use the precut foam pads as an aid. 3 Angle Profile Edges for the Bottom and Cover 1) Position the angle profile edges (1) on the center of the bottom and cover edges. The distance to the edges has to be the same on the left and right side. Later on, the lateral angle profile edges (2) will be inserted at these positions. 2) Mark the holes of the angle profile edges on the wood panels. 3) Drill 4.3 mm holes. Fix the angle profile edges with the thin rivets. Always apply sufficient and equal pressure to the rivet tool in order to obtain good riveting. 2 1 2 Stage Line MZF-55.. R Flight Case Series 4 Locking Profiles and Angle Profile Edges for the Side Panels The locking profiles are fixed to the joint edges of the cover and bottom. They are angled with 45° and consist of a male component (4) for the bottom and a female component (3) for the cover. If locks and hinges are used for the flight case, the corresponding locking profiles are cut off straight at the side at which the lock and the hinge are going to be installed. Pay attention that these locking profiles are installed at those positions at which the lock resp. the hinge is going to be installed. 3 4 1) Debur the edges of the locking profiles with a metal file. 2) Lay the locking profiles onto the edges. Fix them with the supplied corner brackets (5). Place these corner brackets on the locking profiles and make marks for the mounting holes. 5 5 3) Then drill 4.3 mm holes only through the outer side of the locking profile and the wood. Thus, the insides of the locking profiles remain smooth. 4) Position the lateral angle profile edges (2). 5) Rivet the fixing corner brackets and thus at the same time the locking profiles with the thin rivets. 6) If necessary, also rivet the lateral angle profile edges (2). For housings with small heights, these angle profile edges will be fixed by the corner brackets (5) and the subsequent mounting of the ball corners only. 5 Ball Corners 1) Place the ball corners on the housing edges. Mark the positions for the holes. 2) Drill 5.2 mm holes. 3) Fasten the ball corners with the larger rivets. In order to obtain a securely fastened ball corner, press onto them while riveting. 6 Locks and Hinges According to the flight case model, the locks and hinges are either designed for standard or recessed installation. The flight cases for 19” units are equipped with two removable covers which must be interchangeable. In this case, first fasten the lock and hinges on one side of the flight case and on the cover. Afterwards, fasten the lock and hinges on the second side of the flight case so that they match exactly to the first cover. Finally, rivet the lock and hinges on the second cover so that they also match exactly. 2 2 Stage Line MZF-55.. R 6.1 Standard Locks and Hinges The lock and hinges consist of two parts except the 90° strut hinge of some models. 1) Always fix the smaller part (6) of the lock resp. hinge to the cover. 2) Drill the holes (4.3 mm) for the rivets only through the outer side of the locking profile and the wood. Thus, the insides of the locking profiles remain smooth. 3) Fasten all components with the thin rivets. 6.2 Recessed Locks and Hinges The lock and hinges are inserted into the recesses of the cover and the housing. 1) Drill the holes (5.2 mm) for the rivets only through the outer side of the locking profile and the wood. Thus, the insides of the locking profiles remain smooth. 2) Fasten the lock with the larger rivets. 3) Mount the hinges according to the drawing and fasten them with the larger rivets. 7 Handles According to the flight case model, the handles are screwed onto the housing (standard mounting) or are riveted into the recess (recessed mounting). 7.1 Standard Handles 1) Drill 5.2 mm mounting holes. 2) Mount the handle with the supplied fastening as well as the M5 screws, washers and nuts. 3) Finally, slip the plastic caps onto the handle fixture. 7.2 Recessed Handles 1) Insert the recessed handles into the lateral housing recesses. 2) Mark the mounting holes. 3) Drill 4.3 mm holes and fasten the handles with the thin rivets. According to the flight case model, the following accessories have to be installed: Flight Case Series 6 Stage Line MZF-55.. R Flight Case Series 8 Mounting Rails for 19” Units The rails are installed exactly behind the locking profile. 1) Drill 6 mm mounting holes. 2) Insert the supplied cage nuts into the rails before fixing. Each rack space requires 2 nuts on each side (e. g. for 4 rack spaces = 8 nuts per rail). 3) Fasten the rails with the supplied screws (M6 x 25 mm). 9 Feet If desired, equip the flight case with feet. 10 Foam Pads All foam pads are self-adhesive. 1) At first, fix the foam pads to the long side panels. 2) Afterwards, cushion all short side panels. 3) Finally, line the bottom and cover areas. 11 Specifications Model MZF-5501 MZF-5504 MZF-5506 MZF-5507 MZF-5509 MZF-5510 MZF-5511 MZF-5512 MZF-5513 MZF-5514 Order No. 24.5240 24.5250 24.5260 24.5320 24.5330 24.5270 24.5340 24.5350 24.5280 24.5360 Application 8 Micros 160 CDs Keyboard Keyboard Guitar Bass Guitar Universal Universal Universal Universal Inside Dimensions (W x H x D) 550 x 350 x 87 mm 550 x 400 x 158 mm 1132 x 412 x 175 mm 1232 x 452 x 185 mm 1102 x 402 x 87 mm 1252 x 452 x 87 mm 600 x 400 x 210 mm 800 x 500 x 472 mm 1000 x 400 x 372 mm 1200 x 500 x 472 mm Model Order No. Rack space* MZF-5521 MZF-5522 MZF-5523 MZF-5524 MZF-5525 MZF-5526 MZF-5527 MZF-5528 24.5290 24.5370 24.5300 24.5380 24.5310 24.5390 24.5400 24.5410 Inside Dimensions (W x H) 513 x 114 mm 513 x 203 mm 513 x 292 mm 513 x 381 mm 513 x 470 mm 513 x 559 mm 513 x 648 mm 513 x 737 mm Weight 4.3 kg 6.5 kg 10.5 kg 11.5 kg 8.1 kg 10.5 kg 6.8 kg 17.0 kg 18.0 kg 23.5 kg 19" racks 2 4 6 8 10 12 14 16 *1 Rack space = 44.45 mm According to the manufacturer. Subject to technical change. Inside Depth (Front/Middle/Back Part) 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm 52/400/52 mm Weight 8.9 kg 11.1 kg 12.0 kg 14.0 kg 14.0 kg 16.5 kg 19.5 kg 21.5 kg