1306 - IC shower chanels
Transcrição
1306 - IC shower chanels
ACO Product catalogue 2007 Shower Channels, FlexDrain NEW ACO Stainless Steel Shower Channel Practical and Attractive go well together The Shower Channel is an easy to install and aesthetically attractive discharge channel for shower locations. Because of the shallow depth and varying lengths the shower channel is suitable for use in new or refurbished projects. As the discharge from the Shower Channel is just one way, this makes the tile work easier. If the Shower Channel is installed at the front of the shower it will function as a barrier against ingress of water whilst maintaining a threshold free access. If the channel is installed with a dividable grating then this can be placed under the shower door. Shower Channel Advantages • Aesthetically attractive • Less tile cutting • Simplified outlets • Easy to maintain • Low installation costs • Removable foul air trap Executive Line Characteristics: • Cross grade for a better water drain • Polished surface • Special foul air trap (P-trap) • Self cleaning • Flow rate up to 1 l/sec. • Telescopic and 360° rotatable trap • • • • • Flower Grate Grate with Square Holes P-trap Wave Grate Grate with Long Holes Water Grate Available with different gratings Flange for isolation Adjusting screws for easy installation Silt basket Low installation depth 2 ERRATA Please correct page 15 in the product catalogue Sanitary products. NEW ACO Stainless Steel Shower Channel Executive Line Shower channel with P-trap Length Shower channel L (mm) 70 with P-trap, L without grate 405766 585 405767 685 405768 785 405769 885 405770 985 405771 1085 405772 1185 405773 Length Grating for Executive line L (mm) shower channels 1 grate 478 405806 578 405807 678 405808 778 405809 878 405810 978 405811 1078 405812 1178 405813 Length Grating for Executive line L (mm) shower channels 1 wave grate 478 405790 578 405791 678 405792 778 405793 878 405794 978 405795 1078 405796 1178 405797 Length L (mm) 13,5 Ø50 485 L L 70 70 3 Grating for Executive line shower channels 1 grate with square holes 478 405798 578 405799 678 405800 778 405801 878 405802 978 405803 1078 405804 1178 405805 All materials are 304 stainless steel L 70 NEW ACO Stainless Steel Shower Channel Executive Line Length Grating for Executive line L (mm) shower channels 1 flower grate 478 405782 578 405783 678 405784 778 405785 878 405786 978 405787 1078 405788 1178 405789 Length Grating for Executive line L (mm) shower channels L 1 water grate 4 478 405774 578 405775 678 405776 778 405777 878 405778 978 405779 1078 405780 1178 405781 L 70 70 ACO Stainless Steel Shower Channel Comfort Line Characteristics: • Removable stainless steel foul air trap • With or without flange for isolation • 3 part gratings for under door installation • 3 different kinds of gratings • Set - channel, grate and foul air trap available under one article number • Low foul air trap Shower channel Gully with plastic foul air trap Earthing Point Part grating section Concrete Ties Shower channel Installation Shower channel Installation - 90° angle 5 ERRATA Please correct page 15 in the product catalogue Sanitary products. ACO Stainless Steel Shower Channel Shower channel with stainless steel foul air trap Shower channel with stainless steel foul air trap 3 grates 485 402738 403780 585 402739 403781 685 402740 403782 785 402741 403783 885 402742 403784 985 402743 403785 1085 402744 403786 1185 402745 403787 Length Shower channel with stainless steel L (mm) foul air trap, flange for isolation 3 grates 403797 403805 585 403798 403806 685 403799 403807 785 403800 403808 885 403801 403809 985 403802 403810 1085 403803 403811 1185 403804 403812 Length Shower channel with stainless steel L (mm) foul air trap and flange for isolation 20 70 L 13,5 Ø50 1 grate 485 70 L Ø50 1 grate 100 L (mm) 100 Length 1 wave grate 404484 685 404485 785 404486 885 404487 985 404488 1085 404489 1185 404490 13,5 Length Shower channel with stainless steel L (mm) foul air trap and grate with square holes 1 grate 3 grates 404507 404515 585 404508 404516 685 404509 404517 785 404510 404518 885 404511 404519 985 404512 404520 1085 404513 404521 1185 404514 404522 70 L 20 Ø50 485 All materials are 304 stainless steel 100 585 70 L 100 404483 Ø50 6 485 ACO Stainless Steel Shower Channel flange for isolation and grate with square holes 3 grate 404491 404499 585 404492 404500 685 404493 404501 785 404494 404502 885 404495 404503 985 404496 404504 1085 404497 404505 1185 404498 404506 Length Shower channel decrease version with L (mm) stainless steel foul air trap and socket 3 grates 405750 405742 585 405751 405743 685 405752 405744 785 405753 405745 885 405754 405746 985 405755 405747 1085 405756 405748 1185 405757 405749 13,5 70 L 20 Ø50 1 grate 485 70 L Ø50 1 grate 485 100 Shower channel with stainless steel foul air trap, L (mm) 60 Length 7 All materials are 304 stainless steel ACO Stainless Steel Shower Channel Shower channel with plastic foul air trap Length Shower channel with plastic L (mm) foul air trap 1 grate 405598 685 405599 785 405600 885 405601 985 405602 1085 405603 1185 405604 Length Shower channel with plastic L (mm) foul air trap 20 100 405597 585 Ø40 485 70 L 1 wave grate 585 404364 685 404365 785 404366 885 404367 985 404368 1085 404369 1185 404370 Length Shower channel with plastic L (mm) foul air trap 70 L 20 100 404363 Ø40 485 1 grate with square holes 405606 685 405607 785 405608 885 405609 985 405610 1085 405611 1185 405612 Length Shower channel with plastic L (mm) foul air trap and flange 70 L 20 100 405605 585 Ø40 1 wave grate 404371 585 404372 685 404373 785 404374 885 404375 985 404376 1085 404377 1185 404378 All materials are 304 stainless steel 70 L 13,5 Ø40 485 100 8 485 ACO Stainless Steel Shower Channel Shower channel without foul air trap Length Shower channel without L (mm) foul air trap 1 grate 485 403006 585 403007 685 403008 785 403009 885 403010 985 403011 1085 403012 1185 403013 Length Shower channel without L (mm) foul air trap 70 L 20 Ø50 3 grates 485 403014 585 403015 685 403016 785 403017 885 403018 985 403019 1085 403020 1185 403021 L 70 20 Ø50 9 All materials are 304 stainless steel ACO Stainless Shower Channel Flow rates Comfort Line Comfort Line decrease version St andard channel Shower channel decrease version 0,7 0,45 0,40 0,6 0,35 Flow rate (l/s) Flow rate (l/s) 0,5 0,4 0,3 0,2 0,30 0,25 0,20 0,15 0,10 0,1 0,05 0 0,0 0 10 20 30 40 Head of water (mm) 50 0,0 5,0 10,0 15,0 Head of water (mm) Exclusive Line St andard channel 1,20 Flow rate (l/s) 1,00 0,80 0,60 0,40 0,20 10 0,0 0,0 5,0 10,0 15,0 20,0 Head of water (mm) 25,0 30,0 20,0 25,0 30,0 ACO Stainless Steel Shower Channel Installation instructions Where is it possible to use the ACO shower channel? The shower channel can be installed in newly constructed buildings as well as renovation projects. It is necessary to prepare sufficient space in the floor for the body of the shower channel and the waste pipe. The shower channels are available in various standard lengths so that it is possible to select the most suitable product for a given application. Channels are available in designs with sectioned gratings to facilitate installation under shower doors. Necessary materials • • • • • Self-adhesive tape; Spirit level; Emery paper; Degreasing agent; Silicone sealant Important! 1. The off-take capacity of the channel is not only determined by the capacity of the actual channel itself, but also the waste pipe to which these elements are to be connected. Please adhere to the following instructions: • The length of the waste pipeline to the vertical waste stack of the system must be as short as possible; • Avoid bends in the system where possible; • Make sure that the waste pipe has a suffi- cient gradient for the discharge required; • The diameter of the waste pipeline must be at least 50 mm (or 40mm by plastic FAT). 2. The capacity of the shower channel is approximately 20 l/min (tested according to EN1253), which is more than sufficient for a majority of shower types. If the shower channel is used for multiple showers or for showers with a higher capacity please contact your supplier. 3. Select a Showerchannel length so that it can be placed between the walls without any additional tiles. The shower channel can be placed both in the rear of the shower area or to the front, the former option tends to be preferred. 4. If the shower channel is installed under the shower door, it is necessary to use of the shower channel with a sectioned grating so that removal is possible. Assembly 1. 2. 3. 4. 5. Before installing the shower channel, please remove the gratings in order to avoid damage. Further protection is afforded by applying adhesive tape to the edge of the shower channel. Make sure that no impurities (mortar, etc.) can get into the shower channel during assembly and installation work. We recommend that it is temporarily covered during these processes. We recommend to use the emery paper to roughen the side and bottom sections of the shower channel, then use degreasing agent to achieve better adhesion to the floor materials. Connect the channel to the waste pipe making sure that the pipe is inserted as far as possible (regardless of the pipe type – whether PVC, PE or PP). If required ground the channel by connect- 6. 7. 8. 9. ing the grounding conductor to the grounding point of the drainage body. Level the channel with the help of the extension brackets (fasten these brackets with screws) or install the channel in mortar. Fill in the space under the channel and around it with cement mortar, taking into account the thickness of the tiles. While laying the tiles, it is necessary to make sure that the gradient in the shower area is always directed towards the shower channel. Place the tiles at least 1 to 2 mm higher than the upper side of the shower channel edge, in order to avoid pooling along the channel. After tiling, seal the tiles to the channel with a silicon sealant, complying with the recommendations of the manufacturer. For best results, make sure the silicon joint has the same width and colour as the joint between the tiles. 10. Remove any cement or jointing agent residue carefully with the help of a plastic wool/sponge. 11. Remove the protective film from the grating then install the grating back into the channel. Cleaning and maintenance Stainless steel is vulnerable to scratches. When cleaning, do not use sharp or abrasive materials. Use common household detergents for bathrooms or specialist cleaning agents for stainless steel. The shower channel does not require any special maintenance, but we recommend that you remove regularly the foul air trap to check the drainage body for contamination and to remove any possible impurities. 11 ACO Stainless Steel Shower Channel ACO FlexDrain Length Shower channel L (mm) telescopic 1 grate 404531 585 404532 685 404533 785 404534 885 404535 985 404536 1085 404537 1185 404538 Length Shower channel L (mm) telescopic 90 L 50 485 20 Ø75 3 grates 404539 585 404540 685 404541 785 404542 885 404543 985 404544 1085 404545 1185 404546 Length Shower channel L (mm) telescopic 90 L 50 485 20 Ø75 1 grate 585 404385 685 404386 785 404387 885 404388 985 404389 1085 404390 1185 404391 Length Shower channel L (mm) telescopic L 13,5 90 Ø75 50 404384 3 grates 485 404523 585 404524 685 404525 785 404526 885 404527 985 404528 1085 404529 1185 404530 L 13,5 50 12 485 Ø75 90 ACO Stainless Steel Shower Channel ACO FlexDrain Gully Product Part Nr. 75 75 50 50 403921 404682 DN DN DN2 DN 2 (mm) DN2 Plastic gully Plastic gully with flange DN (mm) ACO FlexDrain Gully Tops Product Gully top domestic standard Gully top domestic design, with flange Gully top professional standard Gully top professional sport Gully top professional sport with flange Gully top industrial Product Foul air trap AxB Loading class Grate H (mm) Part Nr. AISI 304 150x150 150x150 200x200 200x200 150x150 150x150 200x200 200x200 300x300 300x300 150x150 K K K K K K K K K K K perforated -brushed perforated - polished perforated -brushed perforated - polished blasted for tiles blasted for tiles blasted for tiles perforated 30 30 30 30 34 34 34 34 34 34 12 404428 404429 404430 404431 404434 404436 404455 404456 404459 404460 404123 200x200 150x150 150x150 150x150 200x200 200x200 200x200 300x300 300x300 300x300 150x150 150x150 150x150 200x200 200x200 200x200 300x300 300x300 300x300 200x200 K K L L K L L K L L K L L K L L K L L L perforated perforated - 6mm perforated - 6mm perforated - 15mm perforated - 6mm perforated - 6mm perforated - 15mm perforated - 6mm perforated - 6mm perforated - 15mm perforated - 6mm perforated - 6mm perforated - 15mm perforated - 6mm perforated - 6mm perforated - 15mm perforated - 6mm perforated - 6mm perforated - 15mm mesh - antislip 12 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 65 404124 404437 404438 404439 404443 404444 404445 404449 404450 404451 404440 404441 404442 404446 404447 404448 404452 404453 404454 404638 200x200 200x200 200x200 200x200 200x200 200x200 200x200 250x250 250x250 250x250 250x250 250x250 250x250 250x250 250x250 300x300 300x300 300x300 300x300 300x300 300x300 300x300 300x300 L L L L L M M L L L L L L M M L L L L L L M M mesh perforated cover perforated perforated ladder slot cover mesh - antislip mesh perforated no grate - cover perforated perforated ladder slot cover mesh - antislip mesh perforated no grate - cover perforated perforated ladder slot cover 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 65 404639 404640 404641 404642 404643 404644 404645 404646 404647 404648 404649 404650 404651 404652 404653 404654 404655 404656 404657 404658 404659 404660 404661 DN 1 (mm) Part Nr. AISI 304 75 404143 B Ax B Ax Ø75 Ax B Ø75 B Ø75 Ax Ø75 B Ax Ø75 Ax 13 B Ø75 Notes 14 Subject to technical changes without notice © ACO Industries k.s. All reasonable care has been taken in compiling the information in this document. All recommendations and suggestions on the use of ACO products are made without guarantee since the conditions of use are beyond the control of the Company. It is the customer’s responsibility to ensure that each product is fit for its intended purpose and that the actual conditions of use are suitable. This brochure and any advice is provided ACO Industries k.s. (the company) free of charge and accordingly on terms that no liability (including liability for negligence) will attach the Companyor its servants or agents arising out of or in connection with or in relation to this brochure or any such advice. Any goods supplied by the Company will be supplied solely upon its standard conditions of sale, copies of which are available on request. The Company’s policy of continuous product development and improvement renders specifications liable to modification. information provided in this brochure is therefore subject to change without prior notification. 1306/IC Shower channels/En/11/06/JL ACO Industries k.s. 582 22 Přibyslav Havlíčkova 260 Tel.: +420 569 491 111 Fax: +420 569 482 529 www.aco.cz e-mail: [email protected] Czech republic