COLOUR CHANGING PANEL 19214
Transcrição
COLOUR CHANGING PANEL 19214
Page 1 of 8 Copyright ROMPA® Ltd COLOUR CHANGING PANEL 19214 CONTENTS 1 x Colour Changing Panel NOTE: No fixings are included for wall mounting (please seek professional advice regarding construction of wall – see below). TO WALL MOUNT PANEL IMPORTANT: This panel weighs approximately 20kg. Please take this into consideration when fixing. Please make sure that you are aware of the construction of the wall the panel is to be fixed to. Taking this into account please ensure that you use the correct fittings. For example, walls may be partition walls and plaster board as opposed to solid brick or stone walls. Take advice from a suitably qualified professional builder or from an estates department if in any doubt about appropriate fixtures. Attach fixings such as mirror plates to the back of the panel. Fixings are not supplied as these depend on the surface the panel will be fixed to. Check the fixings e.g. mirror plates you buy can easily support 20kg. You may wish to attach two mirror plates to the back of the panel at the top and two on the back at the bottom. Note: When attaching fixings to the back of the panel please proceed with caution – be aware that there are electrical assemblies inside the panel. Alternatively, this Panel may be used in a Porter 18518/18522 – see ROMPA® catalogue/website for further information. DESCRIPTION An interactive colour changing mood panel with sound, that is Everysense® compatible. This panel is also WiFi compatible – it will wirelessly control other WiFi products, such as the Colour Match Panel, Rompa® Light Source and Rompa® Bubble Tubes. Is also WiFi responsive and can be wirelessly controlled by the Talking Cube and 8 Way Super Interactive Switch Box. This panel has an acrylic plastic front housing an array of 10 colourful LED back-lit push buttons. The plastic surround is textured and the whole panel can be switched ON/OFF using the ON/OFF switch at the top of the panel. COLOUR CHANGING PANEL 19214 KH 4.10 Page 2 of 8 Copyright ROMPA® Ltd OPERATION 1. Plug into mains socket. Keep mains cable out of reach. 2. Turn whole panel on using ON/OFF switch. 3. To select panel colour, use coloured buttons: RED = whole panel changes to RED GREEN = whole panel changes to GREEN BLUE = whole panel changes to BLUE YELLOW = whole panel changes to YELLOW To add more or less of a particular colour, just press the corresponding colour up and down arrow buttons. In this way, the user can select their own preferred hue. Users are rewarded for each button press with button sounds. TECHNICAL SPECIFICATION Size: 115 x 72.5 x 11 cm Weight: 20kg Input: 100-240v AC 50/60Hz 0.7A Output: 12v DC 5A 60W max Conforms to BS EN 9001-2000 The panel cover is phthalate-free COLOUR CHANGING PANEL 19214 KH 4.10 Page 3 of 8 Copyright ROMPA® Ltd SAFETY Always supervise the use of this product Handle with care For indoor use only The panel is to be used in dry environments. The ambient temperature should not exceed 40ºC. TROUBLESHOOTING Panel does not light up 1. Ensure that the panel is plugged in and switched on 2. Ensure that an Everysense® system is not running nearby as it may send signals to disable the panel. 3. Turn the panel OFF, wait 1 minute, and then turn ON again to re-initialise the panel. Panel sometimes changes colour randomly, and then goes back to its pre-programmed sequence. 1. The panel may be picking up WiFi signals from somebody nearby who has another Colour Changing Panel or 8 Way Multifunction Switch (or an Everysense® room). 2. If you have 2 neighbouring rooms each using WiFi products, then the devices in both rooms can be controlled by any nearby WiFi controllers. An "All-In-One" Controller would be required to alter the wireless settings to operate without interfering with one another. There are no replaceable fuses in this unit. If in doubt turn the power off, wait 1 minute and turn it on again. SUGGESTIONS FOR USE For maximum visual effect, use in a darkened room. WiFi compatible – may be used to wirelessly control ROMPA® Wall Panels e.g. the Colour Match Panel 19209, Rompa® Light Source 19210 (and so fibre optics, Star Cloths etc) and Rompa® Bubble Tubes e.g. 19772. This panel is also responsive to WiFi products and can be controlled by the Talking Cube 18870, Wireless Interactive Carpet Switch Set 19939 and 8 Way Super Interactive Switch Box 19213 (all to be purchased separately). COLOUR CHANGING PANEL 19214 KH 4.10 Page 4 of 8 Copyright ROMPA® Ltd PANNEAU DE COULEURS CHANGEANTES 19214 CONTENU 1 x panneau de couleurs changéantes NOTEZ: Ce panneau ne comprend pas des installations. Avant de le fixer au mur, il faut vérifier la construction du mur et cherchez des conseils convenables. POUR ATTACHER LE PANNEAU AU MUR IMPORTANT: Ce panneau pèse vers 20 kilos. Prenez cette information en considération quand vous fixez le collier au mur. Tenez compte de la construction du mur sur lequel vous allez fixer le collier. Tout bien considérez quand vous achetez des installations. Par exemple, le mur pourrait être une cloison, de Placoplâtre® ou un mur solide en brique. En cas de doute en ce qui concerne les installations, cherchez les conseils d’un maçon convenablement qualifié ou votre service de maintien. Attachez des installations à l’arrière du panneau et puis utilisez les installations pour fixer le panneau au mur. Les installations ne sont pas comprises – elles dépendent la construction de votre mur et devraient supporter 20 kilos sans risque. On pourrait utiliser par exemple les plaques – deux à l’arrière en haut et deux autres à l’arrière en bas. Notez : En attachant des installations à l’arrière du panneau, prenez soin – tenez compte des parties électriques à l’intérieur du panneau. Comme alternative, on peut se server de ce panneau dans un Support 18518/18522 – voir le catalogue ou web ROMPA® pour des renseignements. DESCRIPTION Un panneau interactif qui change couleur et fait des sons. Ce panneau est compatible avec everysense®. Ce panneau est compatible avec WiFi – il règle les autres produits WiFi comme le Panneau Couleurs Composants, la Source Lumineuse Rompa® et les Colonnes à Bulles Rompa®. Ce panneau réagit à WiFi – on peut le contrôler avec le Cube Parlant et le Super Contacteur Interactif 8 Côtés. Le panneau est en plastique et il a dix boutons illuminés par des DEL. Il y a bouton pour allumer/éteindre le panneau (au-dessus du panneau) COLOUR CHANGING PANEL 19214 KH 4.10 Page 5 of 8 Copyright ROMPA® Ltd FONCTIONNEMENT 1. Branchez. Gardez le câble hors de la portée. 2. Allumez le panneau en vous servant du bouton pour allumer/éteindre. 3. Pour choisir une couleur, servez-vous des boutons colorés: ROUGE = change le panneau en rouge VERT = change le panneau en vert BLEU = change le panneau en bleu JAUNE = change le panneau en jaune Pour varier l’intensité de la couleur, appuyez sur les flèches correspondantes (plus/moins). De cette façon l’usager peut choisir sa teinte préférée. Chaque fois qu’on appuie sur un bouton, le panneau vous récompense avec des sons. CARACTERISTIQUES TECHNIQUES Dimensions : 115 x 72,5 x 11 cm Poids : 20 kilos Alimentation : 100-240v AC 50/60Hz 0,7A Sortie: 12v DC 5A 60W max Conforme à BS EN 9001-2000 Le couvercle de ce panneau ne contient pas de plastifiant COLOUR CHANGING PANEL 19214 KH 4.10 Page 6 of 8 Copyright ROMPA® Ltd SURETE Il faut toujours surveiller l’usage de ce produit Maniez ce produit avec soin Pour l’usage à l’intérieur seulement Pour l’usage au sec seulement La température ambiente ne devrait pas dépasser 40ºC. EN CAS DE PROBLÈMES L panneau ne s’allume pas 1. Vérifiez que le panneau est branché et allumé 2. Vérifiez qu’un autre système Everysense® ne fonctionne pas tout près car il peut régler l’autre systeme et éteindre ce panneau. 3. Eteignez, attendez une minute et puis allumez de nouveau. Quelquefois le panneau change de couleur au hasard, et puis retourne à la séquence déjà programmé. 1. Le panneau peut réagir aux signaux d’un autre Panneau de Couleurs Changeantes ou d’un contacteur aux huit boutons pour Everysense®. 2. Si vous avez deux salles l’un à côté de l’autre et tous les deux contiennent des produits WiFi, tous ces produits s’activent avec les mêmes appareils de contrôle. On peut acheter un côntroleur multiple ("All-In-One" Controller) pour éviter ces problèmes. Il n’y a pas de fusibles remplaçables dans ce panneau. En cas de doute, éteignez, attendez une minute et puis allumez de nouveau. SUGGESTIONS POUR L’USAGE Pour un effet plus attirant, servez-vous de ce produit dans une salle sombre. Ce produit est compatible avec WiFi – il règle les autres produits WiFi comme le Panneau Couleurs Composants 19209 , la Source Lumineuse Rompa® 19210 et les Colonnes à Bulles (ex.19772). Ce panneau réagit à WiFi – on peut le contrôler avec le Cube Parlant 18870, le Tapis Interactif sans fil - set de contacteurs 19939 et le Super Contacteur Interactif 8 Côtés 19213. Ces produits se vendent séparément. COLOUR CHANGING PANEL 19214 KH 4.10 Page 7 of 8 Copyright ROMPA® Ltd PAINEL MUDANÇA DE CORES 19214 CONTEÚDO 1 x Painel Mudança de Cores NOTA: Os acessórios de fixação não estão incluídos para montar na parede (procure a ajuda de um profissional no que respeita à construção da parede – ver abaixo). PARA MONTAR O PAINEL NA PAREDE IMPORTANTE: Este painel pesa aproximadamente 20 Kg. Tenha isto em consideração quando o fixar. Tenha consciência da construção da construção da parede em que o painel vai ser montado. Tendo isto em consideração, verifique se está a utilizar os acessórios de fixação correctos. Por exemplo, as paredes podem fazer divisão com outro compartimento. E se essa parede for de gesso a fixação é diferente a uma parede de tijolo ou de pedra. Peça a opinião a um profissional qualificado. Coloque acessórios de fixação como ganchos de suspensão na parte de trás do painel. Os acessórios de fixação não são fornecidos pois dependem da superfície onde o painel irá ser montado. Verifique se os acessórios que vai comprar aguentam facilmente 20 Kg. Pode querer colocar por exemplo dois ganchos de suspensão em cima e dois na parte de baixo. Nota: quando colocar acessórios de fixação na parte de trás do painel tenha cuidado – tenha em mente que existem componentes eléctricos dentro do painel. Em alternativa, este painel pode ser pode ser utilizado num suporte 18518/18522 – veja no catálogo/site para mais informação. DESCRIÇÃO Um Painel Mudança de Cor Interactivo com som, que é compatível com Everysense. Este painel também é compatível com WiFi – vai controlar outros produtos WiFi sem fios, tais como o Painel Combinação de Cores, a Fonte de Luz e Colunas de Água. Também responde por Wifi e pode ser controlado pelo Cubo Falante e Painel Super Interactivo de 8 botões sem fios. Este painel tem uma cobertura plástica e 10 botões com LEDs coloridos. A cobertura plástica tem textura e todo o painel pode ser ligado/desligado utilizado o botão ON/OFF no topo do painel. COLOUR CHANGING PANEL 19214 KH 4.10 Page 8 of 8 Copyright ROMPA® Ltd FUNCIONAMENTO 1. Ligue à corrente. Mantenha o cabo de alimentação fora do alcance. 2. Ligue o painel utilizando o botão ON/OFF. 3. Para seleccionar a cor do painel, utilize os botões coloridos: VERMELHO= Todo o painel fica vermelho VERDE= Todo o painel fica Verde AZUL= Todo o painel fica Azul AMARELO= Todo o painel fica amarelo Para adicionar mais ou menos de uma determinada cor, pressione o botão correspondente à cor para cima ou para baixo. Desta forma, o utilizador pode seleccionar a sua cor preferida. Os utilizadores são recompensados com sons quando pressionam os botões. ESPECIFICAÇÕES TÉCNICAS Tamanho: 115 x 72.5 x 11cm Peso: 20Kg Input: 100-240v AC 50/60Hz 0.7ª Output: 12v DC 5ª 60W Max Conforme BS EN 9001-2000 A cobertura deste painel não possui ftaláto COLOUR CHANGING PANEL 19214 KH 4.10
Documentos relacionados
COLOUR MATCH PANEL – 19209
If you have 2 neighbouring rooms each using WiFi products, then the devices in both rooms can be controlled by any nearby WiFi controllers. An "All-In-One" Controller would be required to alter the...
Leia mais