Bartels Micropumps
Transcrição
Bartels Micropumps
EN DE Seite 14 mp6 – double actuator micropump Bartels Micropumps Micropumps transporting the tiniest amounts of gases or liquids can be considered the heart of microfluidics. In many sectors they have become indispensable. Dosing lubricants, feeding sensors with sample gas or mixing starch into the steam of flat irons are only a few of the manifold tasks they can fulfill. Many further fields of application for example are located in medical technologies and analytics. mp5 – smallest available plastic micropump Extremely small in size and low in weight, with good particle tolerance and temperature resistance, Bartels micropumps are well prepared to be used in any of these sectors. As they are almost completely made of plastics, large quantities of these pumps can be produced at low cost and so may well be used as disposables. The functional principle of the Bartels micropumps is based on a Functional principle. piezoelectric diaphragm in combination with passive check valves. A piezo ceramic mounted on a coated brass membrane is deformed when voltage is applied. By the resulting down stroke, the medium is being displaced out of the pump chamber below. The check valves on both sides of the pump chamber define the flow direction. When the voltage decreases, the corresponding piezo deformation causes an upstroke of the membrane. The medium is sucked in and the chamber is filled again. In every second, the pump can do several hundreds of such pumping cycles. The pumping performance can be influenced by adjustment of the parameters. Important advantages for all users result from the radically simple pump design: Injection molded parts for housing and pump chamber, piezo actuators and passive valves constitute the key components. Thus any adaptation to specific requirements concerning flow rate or back pressure is easy to realize. This customization of micropumps with the appropriate electronic controllers is part of the services offered by Bartels Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 1 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 microComponents. If requested, the pumps can be fully integrated into complex system designs as well. Once the perfect pump for your application has been found, you may purchase an exclusive production license for this version to include the component into your own production processes. Of course Bartels microComponents can also realize a high quality serial production for you at low cost. mp6 Micropump The Bartels micropump mp6 combines two piezo actuators inside a single housing. The new pump joins the established functional principle and central advantages of its parent generation mp5 with its own specific innovative features. The small power pack can handle twice the back pressure the mp5 can cope with, has an increased priming capability and is of higher bubble tolerance, so that even gas-liquid-mixtures can be pumped without problems. Its low power consumption is a further advantage. In the entire pump only one material gets into contact with the medium. Now two types of materials are available. In the standard mp6 all relevant parts are made of polyphenylsulfone (PPSU) and in the mp6-pp of polypropylene (PP). The mp6 can already be offered at low prices for large quantities due to an automated assembly. The mp6-pp is produced less automated but for larger quantities it can also be transferred into serial production. mp5 Micropump The mp5 from Bartels microComponents is the smallest and lightest micropump available. Since 2004 the mp5 has successfully shown the potential of piezo membrane pumps. Due to the limited bubble tolerance and higher price in medium quantities, it is now replaced by its successor the mp6 in many applications. If size is a challenging factor, then the mp5 is still the right choice. Its low power consumption and tiny size makes the mp5 the perfect pump to be fully integrated into your product's design. Test the mp5 now and ask Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 2 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 about the possibilities of a customer specific adaptation - for your individual micropump. Typical characteristics of the Bartels micropumps: volume flow versus pressure volume flow versus frequency volume flow versus amplitude Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 3 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technical Data of the mp61 mp6 Pump type Number of actuators Order code: mp6 piezoelectric diaphragm pump 2 30 x 15 x 3.8 mm Dimensions without connectors 1.1811 x 0.5906 x 0.1498 in. Weight 2g barbed tube clip, Fluidic connectors (outer diameter 1.9 mm, length 3.5 mm) 2 Electric connector flex connector 1.25 mm pitch Power consumption < 200 mW Self-priming yes 3 Pumping media liquids, gases, mixtures Operating temperature 0–70°C Life time 5000 h 4 IP code IP33 5 Material in contact with media polyphenylsulfone (PPSU) 6 Suitable evaluation controller mp-x, mp6-EVA and mp6-OEM Typical values of flow and back pressure for selected media (values defined with mp-x: 250 V, SRS): Liquids – water max. volume flow 7 ml/min +/- 15% (5.95 ml/min – 8.05 ml/min) 4 max. back pressure 600 mbar +/- 15% (510 - 690 mbar) 4 1 2 3 4 5 6 Typical values. Values can vary under application conditions. Content is subject to changes without notice. Recommended tubing: 1.3 mm inner diameter. Conditions: Suction pressure < 10 mbar, DI water, settings mp-x: 100 Hz, 250 V, SRS, the max. volume flow will be reached after a few minutes of operation time. Conditions: DI water, room temperature, settings mp-x: 100 Hz, 250 V, SRS Can be changed to IP44. The mp6 is not stable against concentrated alcoholic solutions as MeOH or EtOH. Please find more information concerning the controller and the equipment in the corresponding data sheets. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 4 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technical Data of the mp6-AIR1 mp6-AIR Order code: mp6-AIR Pump type Number of actuators piezoelectric diaphragm pump 2 30 x 15 x 3.8 mm Dimensions without connectors 1.1811 x 0.5906 x 0.1498 in. Weight 2g barbed tube clip, Fluidic connectors (outer diameter 1.9 mm, length 3.5 mm) 2 Electric connector flex connector 1.25 mm pitch Power consumption < 200 mW Self-priming yes 3 Pumping media gases Operating temperature 0 – 70°C Life time t.b.d. IP code IP 33 4 Material in contact with media polyphenylene sulphone (PPSU) 5 Suitable evaluation controller mp-x, mp6-EVA and mp6-OEM Typical values of flow and back pressure for selected media (values defined with mp-x: 250 V, SRS): Gases typ. max. volume flow 18 ml/min (300 Hz) 6 typ. max. back pressure 100 mbar (300 Hz) 6 1 2 3 4 5 6 Typical values. Values can vary under application conditions. Content is subject to changes without notice. Recommended tubing: 1.3 mm inner diameter. Conditions: Gases, room temperature, settings mp-x: 300 Hz, 250 V, SRS, the max. volume flow will be reached after a few minutes of operation time. Can be changed to IP44. The mp6 is not stable against concentrated alcoholic solutions as MeOH or EtOH. Conditions: Gases, room temperature, mp-x: 300 Hz, 250 V, SRS The mp6-AIR is a regular mp6 that was specifically measured for gas flow. Please find more information concerning the controller and the equipment in the corresponding data sheets. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 5 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technical Data of the mp6-pp1 mp6-pp Pump type Number of actuators Order code: mp6-pp piezoelectric diaphragm pump 2 30 x 15 x 3.8 mm Dimensions without connectors 1.1811 x 0.5906 x 0.1498 in. Weight 2g barbed tube clip, Fluidic connectors (outer diameter MIN 1.77 mm - MAX 1.85 mm, length 3.5 mm) 2 Electric connector flex connector 1.25 mm pitch Power consumption < 200 mW Self-priming yes 3 Pumping media liquids, gases and mixtures Operating temperature t.b.d. Life time t.b.d. IP code IP 33 4 Material in contact with media polypropylene (PP) 6 Suitable evaluation controller mp-x, mp6-EVA and mp6-OEM Typical values of flow and back pressure for selected media (values defined with mp-x: 250 V, SRS): Gases max. volume flow 14 ml/min +/- 15% (11.9 – 16.1 ml/min) 5 max. back pressure 150 mbar +/- 15% (127.5 – 172.5 mbar) 5 Liquids – water max. volume flow 5 ml/min +/- 15% (4.25 – 5.75 ml/min) 6 max. back pressure 650 mbar +/- 15% (552.5 mbar – 747.5 mbar) 6 Liquids - MeOH max. volume flow 6.8 ml/min 7 max. back pressure 550 mbar 7 1 2 3 4 5 6 7 Typical values. Values can vary under application conditions. Content is subject to changes without notice. Recommended tubing: 1.02 mm inner diameter. MIN & MAX values due to injection molding shrink. Conditions: Suction pressure < 10 mbar, DI water, settings mp-x: 100 Hz, 250 V, SRS, the max. volume flow will be reached after a few minutes of operation time. Kann auf IP44 angepasst werden. Conditions: Gases, room temperature, mp-x: 300 Hz, 250 V, SRS Conditions: DI water, room temperature, settings mp-x: 100 Hz, 250 V, SRS Conditions: DI water, room temperature, settings mp-x: 100 Hz, 250 V, SRS Please find more information concerning the controller and the equipment in the corresponding data sheets. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 6 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technical Data of the mp51 mp5 Pump type Number of actuators Order code: mp5 piezoelectric diaphragm pump 1 14 x 14 x 3.5 mm Dimensions without connectors 0.5512 x 0.5512 x 0.1378 in. Weight 0.8 g barbed tube clip, Fluidic connectors (outer diameter 2 mm, length 3 mm) 2 Electric connector flex connector / phone jack Power consumption < 200 mW Self-priming yes 3 Pumping media liquids or gases Operating temperature 0 – 70°C Life time 5000 h 4 IP code IP44 polyphenylsulfone (PPSU), polyimide (PI), nitrile Material in contact with media butadiene rubber (NBR) 5 Suitable evaluation controller mp-x, mp6-EVA and mp6-OEM Typical values of flow and back pressure for selected media (values defined with mp-x: 250 V, SRS): Gases max. volume flow 15 ml/min (300 Hz) 6 max. back pressure 30 mbar (300 Hz) 6 Liquids – water max. volume flow 5 ml/min (100 Hz) 4 max. back pressure 250 mbar (100 Hz) 4 1 2 3 4 5 6 Typical values. Values can vary under application conditions. Content is subject to changes without notice. Recommended tubing: 1.3 mm inner diameter. Conditions: Suction pressure < 10 mbar, DI water, settings mp-x: 100 Hz, 250 V, SRS, the max. volume flow will be reached after a few minutes of operation time. Conditions: DI water, room temperature, settings mp-x: 100 Hz, 250 V, SRS The mp6 is not stable against concentrated alcoholic solutions as MeOH or EtOH. Conditions: Gases, room temperature, mp-x: 300 Hz, 250 V, SRS Please find more information concerning the controller and the equipment in the corresponding data sheets. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 7 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Accessories for the Bartels Micropumps mp-x controller Order code: mp-x Access to the full range of driving parameters. A system for the professional evaluation of the micropumps. 7.5 x 16 x 20 cm Dimensions 2.983 x 6.299 x 7.874 in. Weight ca. 800 g Pumping media liquids, gases mp6: 7 ml/min (SRS, 250 V, 100 Hz), DI-water mp6-AIR: 18 ml/min (SRS, 250 V, 300 Hz), air Max. volume flow mp6-pp: 5 ml/min (SRS, 250 V, 100 Hz), DI-water mp5: 5 ml/min (SRS, 250 V, 100 Hz), DI-water Adjustable parameters amplitude, frequency, signal form Amplitude range 0 – 250 V Frequency range 0 - 300 Hz Signal form SRS, rectangular, sine Power supply mains adaptor Current consumption 750 mA at 7.5 V USB-Port incl. driver one; a CD with driver software is included mp5: 1x-2x connectable micropumps or mp6, mp6-AIR and respectively mp6-pp: 1x mp6-OEM controller Order code: mp6-OEM The OEM-controller drives the micropump at adjustable performance in a package similar to an integrated circuit. It enables integration into system electronics or on a PCB. 10.5 x 20.5 x 6 mm Dimensions 0.4134 x 0.8070 x 0.2362 in. Pumping media liquids, gases Max. volume flow 4.9 ml/min @ 3 VDC supply; 100 Hz (DI-water) 7 ml/min @ 5 VDC supply; 100 Hz Adjustable parameters amplitude, frequency Amplitude range 85 – 270 Vpp 1 25 - 226 Hz Frequency range Signal form Power supply Pumping media Pin arrangement 1 mp-x mp6-OEM (Frequencies up to 1000 Hz are possible; please note that the amplitude will decrease in that case. Frequencies down to 1 Hz are possible with an external clock generator.) similar to rectangular 2.5 – 5.5 VDC (5 V recommended for optimized performance) ca. 30 mA at 5 V DIL 14; horizontal ~2.54 mm, vertical ~7.62 mm Before May 2014: mp6-OEM have an amplitude range of 85 – 235 Vpp Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 8 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-EVA evaluation board Order code: mp6-EVA The evaluation board enables the simple use of the micropump based on the mp6-OEM controller. Next to preset standard parameter (235 Vpp, 100 Hz) the mp6-EVA also allows adjusting the pump parameters flexibly, this partly by external tuning. As the supply voltage of the module can be provided via USB (no data interface), just attach it to a USB power supply and start the evaluation. Alternatively it can also be supplied by a 2.5 – 5 V voltage source. 6.5 x 3 x 2 cm Dimensions 2.5590 x 1.1811 x 0.7874 in. Pumping media liquids, gases Max. volume flow 4.9 ml/min @ 3 VDC supply; 100 Hz (mp6, DI-Water) 7 ml/min @ 5 VDC supply; 100 Hz Adjustable parameters Amplitude, frequency Amplitude range 85 – 270 Vpp 1 25 - 226 Hz Frequency range Signal form Power supply Current consumption 1 mp6-EVA (Frequencies up to 1000 Hz are possible; please note that the amplitude will decrease in that case. Frequencies down to 1 Hz are possible with an external clock generator.) similar to rectangular via USB or 2.5 V – 5.5 VDC ca. 30 mA at 5 V Before May 2014: mp6-EVA have an amplitude range of 85 – 235 Vpp mp6-QuadEVA evaluation board Order code: mp6-QuadEVA The mp6-QuadEVA is an evaluation board that allows controlling up to four mp6 micropumps simultaneously with one setting and up to a frequency of 800 Hz. It is possible to change pump voltage and pump frequency directly with the rotary control elements at the board or via USB. Simple control software is provided with the board. Also any terminal software can be used to remotely control frequency and amplitude or enable/disable each of the four pumps. Dimensions Pumping media Max. volume flow (mp6-AIR, gas: air) Adjustable parameters Amplitude range Frequency range Signal form Power supply Current consumption 1 mp6-QuadEVA 80 x 60 x 16 mm 3.15 x 2.36 x 0.63 in. liquids, gases each single mp6-AIR: ~42 ml/min @ 260 V; 800 Hz amplitude, frequency 0 – 260 Vpp 50 – 800 Hz sine 7.5 V, 1000 mA avg. 220 mA, peak 280 mA1 four connected mp6-AIR @ 260 V and 800 Hz Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 9 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-con connection cable Order code: mp6-con Connector for mp6/mp6-pp to mp-x - Molex FCC 1.25 mm pitch Design and connectors - 85 cm (33.465 in.) cable - Binder 620 connector mp6-con mp6-mol connector Order code: mp6-mol Connector to micropump mp6/mp6-pp for custom made cabling Molex FCC 39532045 Type 1.25 mm pitch packaging unit 10 pieces mp6-mol mp-cv check valve Order code: mp-cv The passive check valve eliminates the back flow of the pumping medium, when the micropump is switched off. It can be connected via tubing. 21 mm x 5.5 mm (length x wrench size) Dimensions 0.82677 x 0.2165 in. Materials in contact with the Silicone, stainless steel pumped media barbed tube clip, length : 5.6 mm Fluidic connectors for tubing with internal diameter: 1.3 mm Cracking pressure typical < 35 mbar Max. back pressure 500 mbar Typical leak rate <20 µl/h for DI-water (at 500 mbar) mp-cv mp-t tubing Inlet/outlet compatible Tygon® tubing Inner diameter 1.3 mm suitable for: mp5, mp6 and mp6-AIR Order code: mp-t ID1.3 mp-t Inner diameter 1.02 mm suitable for: mp6-pp mp-y tubing connector Order code: mp-t ID1.02 Order code: mp-y Y-connector for tubing, for the parallel use of two micropumps: Material polypropylene (PP) 1.3 – 2.6 mm for tubing inner diameters of 0.0512 – 0.1024 in. mp-y Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 10 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Evaluation Sets mp5-go! Set Order code: mp5-go! The evaluation of the mp5 can be started directly with this set. It contains: 3 micropumps mp5 1 mp-x controller 1 meter mp-t ID1.3 tubing mp6-go! Set Order code: mp6-go! The evaluation of the mp6 can be started directly with this set. It contains: 3 micropumps mp6 1 mp-x controller 1 mp6-con 1 meter mp-t ID1.3 tubing mp6-go! Set mp6-basic Set Order code: mp6-basic The evaluation of the mp6 can be started directly with this set. It contains: 3 micropumps mp6 1 mp6-EVA evaluation board 1 meter mp-t ID1.3 tubing mp6-pro Set mp6-basic Set Order code: mp6-pro The evaluation of the mp6 can be started directly on the customer’s circuit board with this set. It contains: 5 micropumps mp6 5 mp6-OEM controller 5 pieces mp6-mol 1 meter mp-t ID1.3 tubing mp6-AIR-go! Set mp6-pro Set Order code: mp6-AIR-go! The evaluation of the mp6-AIR can be started directly with this set. It contains: 3 micropumps mp6-AIR 1 mp-x controller 1 mp6-con 1 meter mp-t ID1.3 tubing Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 11 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-AIR-basic Set Order code: mp6-AIR-basic The evaluation of the mp6-AIR can be started directly with this set. It contains: 3 micropumps mp6-AIR 1 mp6-EVA evaluation board 1 meter mp-t ID1.3 tubing mp6-AIR-pro Set Order code: mp6-AIR-pro The evaluation of the mp6-AIR can be started directly on the customer’s circuit board with this set. It contains: 5 micropumps mp6-AIR 5 mp6-OEM controller 5 pieces mp6-mol 1 meter mp-t ID1.3 tubing mp6-pp-go! Set Order code: mp6-pp-go! The evaluation of the mp6-pp can be started with this set. It contains: 3 micropumps mp6-pp 1 mp-x controller 1 mp6-con 1 meter mp-t ID1.02 tubing mp6-pp-basic Set Order code: mp6-pp-basic The evaluation of the mp6-pp can be started directly with this set. It contains: 3 micropumps mp6-pp 1 mp6-EVA evaluation board 1 meter mp-t ID1.02 tubing mp6-pp-pro Set Order code: mp6-pp-pro The evaluation of the mp6-pp can be started directly on the customer’s circuit board with this set. It contains: 5 micropumps mp6-pp 5 mp6-OEM controller 5 pieces mp6-mol 1 meter mp-t ID1.02 tubing Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 12 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-QuadEVA Set Order code: mp6-QuadEVA The evaluation of the mp6 can be started directly with this set. It contains: 4 micropumps mp6 1 mp6-QuadEVA evaluation board 1 mini-USB-cable 1 meter mp-t ID1.3 tubing mp6-AIR-QuadEVA Set mp6-QuadEVA Set Order code: mp6-AIR-QuadEVA The evaluation of the mp6-AIR can be started directly with this set. It contains: 4 micropumps mp6-AIR 1 mp6-QuadEVA evaluation board 1 mini-USB-cable 1 meter mp-t ID1.3 tubing mp6-pp-QuadEVA Set Order code: mp6-pp-QuadEVA The evaluation of the mp6-pp can be started directly with this set. It contains: 4 micropumps mp6-pp 1 mp6-QuadEVA evaluation board 1 mini-USB-cable 1 meter mp-t ID1.02 tubing The offered accessories and kits are meant to assist your evaluation process. After the feasibility of the micropump in the customer specific application has been proven, an adequate miniaturization of the controller and the equipment can be carried out. The design of customized controllers is part of the services offered by Bartels microComponents. Please contact us, if we can support you in choosing the suitable equipment. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 13 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 DE EN Page 1 mp6 – Doppelaktor-Mikropumpe Bartels Mikropumpen Mikropumpen, die kleinste Mengen von Gasen oder Flüssigkeiten fördern, bilden das Herzstück der Mikrofluidik. Ihre Dienste sind in vielen Bereichen unentbehrlich: Schmiermittel dosieren sie genauso zuverlässig, wie sie Sensoren mit der Probe versorgen oder in Bügeleisen Stärke in den Dampf mischen. Zahlreiche weitere Einsatzgebiete mp5 - kleinste Mikropumpe aus Kunststoff gibt es etwa in der Medizin- und Analysetechnik. Die Bartels Mikropumpen mit ihren extrem kleinen Abmessungen und geringem Gewicht, einer guten Partikeltoleranz und großer Temperaturbeständigkeit sind für all diese Felder gerüstet. Fast vollständig aus Kunststoff produziert, lassen sie sich in hohen Stückzahlen kostengünstig herstellen. Zugrunde liegendes Funktionsprinzip der Mikropumpen ist eine Piezomembran, deren Hub, d.h. Auslenkung und Anzahl, über die elektrische Funktionsprinzip der Mikropumpen Ansteuerung beeinflusst werden kann um die Förderleistung zu variieren. Ventile an beiden Seiten der Pumpkammer geben vor, in welcher Richtung die Fluide aus der Pumpe gedrückt werden. Nutzer profitieren vom einfachen Aufbau der Pumpen: Spritzgussteile für Gehäuse und Pumpkammer, ein Piezoaktor und zwei passive Ventile sind die entscheidenden Bestandteile. Anpassungen des Designs an besondere Kundenanforderungen, etwa bezüglich der Flussrate oder des zu bewältigenden Gegendrucks, sind leicht vorzunehmen. Die Erstellung kundenspezifischer Versionen samt zugehörigen elektronischen Steuerungen ist Teil des Angebots von Bartels microComponents. Auf Wunsch können die Bartels Mikropumpen auch vollständig in komplexe Systeme integriert werden. Sobald die perfekte Pumpe für Ihre Anwendung ermittelt wurde, haben Sie die Möglichkeit, eine exklusive Produktionslizenz für diese Version zu Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 14 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 erwerben, um die Komponente vollständig in Ihre eigenen Produktionsprozesse einzubinden. Oder Bartels microComponents realisiert eine qualitativ hochwertige, kostengünstige Serienproduktion für Sie. mp6 Mikropumpe Die Bartels Mikropumpe mp6, vereint zwei Piezoaktoren in einem gemeinsamen Gehäuse. Somit kombiniert die neue Pumpe das bewährte Funktionsprinzip und die wichtigsten Vorzüge der Vorgängergeneration mp5 mit neuen, innovativen Funktionseigenschaften. Das kleine Kraftpaket kann einen doppelt so hohen Gegendruck bewältigen wie die mp5, verfügt über eine verbesserte Selbstansaugung und weist eine höhere Gasblasentoleranz auf. Damit ist auch das Pumpen von Gas/Flüssigkeitsgemischen für die mp6 kein Problem. Der geringe Energieverbrauch ist ein weiterer Vorzug der mp6. Nur ein einziges Material kommt in der Pumpe in Kontakt mit dem gepumpten Medium. Es sind zwei verschiedene Materialien verfügbar: Zum einen die mp6, bei der alle medienberührenden Teile aus Polyphenylsulfon (PPSU) hergestellt sind. Und seit Mitte 2012 die mp6-pp, bei der alle medienberührenden Teile aus Polypropylen (PP) sind. Die mp6 ist dank der automatisierten Fertigung bereits in hohen Stückzahlen zu kleinen Preisen verfügbar. Die mp6-pp wird derzeit noch teilautomatisiert gefertigt, ist aber ebenso für hohe Stückzahlen in die Serienfertigung übertragbar. mp5 Mikropumpe Die mp5 von Bartels microComponents ist die kleinste und leichteste Mikropumpe auf dem Markt. Seit Ende 2004, hat die mp5 das Potential von piezoelektrischen Membranpumpen unter Beweis gestellt. Aufgrund der begrenzten Blasentoleranz und dem höheren Preis in mittleren Stückzahlen wird sie nun in vielen Anwendungen von ihrem Nachfolger der mp6 abgelöst. Ist die Größe ein absolut ausschlaggebender Faktor, dann ist die mp5 weiterhin die richtige Wahl für Ihre Applikation. Mit ihrem kleinen Energiebedarf und ihrer geringen Größe lässt sich die mp5 ideal in das Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 15 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Design Ihrer Produkte integrieren. Testen Sie jetzt die mp5 und fragen Sie nach den Möglichkeiten kundenspezifischer Anpassungen - für Ihre individuelle Mikropumpe. Typische Charakteristik der Bartels Mikropumpen: Volumenfluss über Druck Volumenfluss über Frequenz Volumenfluss über Amplitude Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 16 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technische Daten der mp61 mp6 Typ der Pumpe Anzahl der Aktoren Abmessungen ohne Fluidanschluss Gewicht Fluidische Anschlüsse Elektrischer Anschluss Stromaufnahme selbstansaugend Pumpmedien Betriebstemperatur Lebensdauer Schutzart Material in Kontakt mit Pumpmedium Geeignete Evaluierungssteuerungen Bestellcode: mp6 Piezomembranpumpe 2 30 x 15 x 3,8 mm 1.1811 x 0.5906 x 0.1498 in. 2g Schlaucholiven, (Außendurchmesser 1,9 mm, Länge 3,5 mm) 2 Flexleitung 1,25 mm Rastermaß < 200 mW ja 3 Flüssigkeiten, Gase und Gemische 0–70°C 5000 h 4 IP33 5 Polyphenylsulphon (PPSU) 6 mp-x, mp6-EVA und mp6-OEM Typische Flussraten und Gegendrücke für bestimmte Medien (Werte bestimmt mit mp-x: 250 V, SRS): Flüssigkeiten - Wasser max. Flussrate 7 ml/min +/- 15% (5,95 ml/min - 8,05 ml/min) 4 max. Gegendruck 600 mbar +/- 15% (510 - 690 mbar) 4 1 2 3 4 5 6 Typische Werte. Werte schwanken abhängig von den Anwendungsbedingungen. Technische Änderungen vorbehalten. Empfohlene Schläuche: 1,3 mm Innendurchmesser. Bedingungen: Saugdruck < 10 mbar, DI-Wasser, Einstellungen mp-x: 100 Hz, 250 V, SRS, max. Förderleistung wird erst nach wenigen Minuten Betriebszeit erreicht. Bedingungen: Destilliertes Wasser, Raumtemperatur, mp-x: 100 Hz, 250 V, SRS Kann auf IP44 angepasst werden. Die mp6 ist nicht beständig gegen konzentrierte Alkohole wie MeOH oder EtOH. Bitte entnehmen Sie Informationen zu den Steuerungen und dem Zubehör den entsprechenden Datenblättern. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 17 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technische Daten der mp6-AIR1 mp6-AIR Typ der Pumpe Anzahl der Aktoren Abmessungen ohne Fluidanschluss Gewicht Fluidische Anschlüsse Elektrischer Anschluss Stromaufnahme selbstansaugend Pumpmedien Betriebstemperatur Lebensdauer Schutzart Material in Kontakt mit Pumpmedium Geeignete Evaluierungssteuerungen Bestellcode: mp6-AIR Piezomembranpumpe 2 30 x 15 x 3,8 mm 1.1811 x 0.5906 x 0.1498 in. 2g Schlaucholiven, (Außendurchmesser 1,9 mm, Länge 3,5 mm) 2 Flexleitung 1,25 mm Rastermaß < 200 mW ja 3 Gase 0–70°C noch nicht definiert IP33 4 Polyphenylsulphon (PPSU) 5 mp-x, mp6-EVA und mp6-OEM Typische Flussraten und Gegendrücke für bestimmte Medien (Werte bestimmt mit mp-x: 250 V, SRS): Gase typ. max. Flussrate 18 ml/min (300 Hz) 6 typ. max. Gegendruck 100 mbar (300 Hz) 6 1 2 3 4 5 6 Typische Werte. Werte schwanken abhängig von den Anwendungsbedingungen. Technische Änderungen vorbehalten. Empfohlene Schläuche: 1,3 mm Innendurchmesser. Bedingungen: Gase, Raumtemperatur, mp-x: 300 Hz, 250 V, SRS, max. Förderleistung wird erst nach wenigen Minuten Betriebszeit erreicht. Kann auf IP44 angepasst werden. Die mp6 ist nicht beständig gegen konzentrierte Alkohole wie MeOH oder EtOH. Bedingungen: Gase, Raumtemperatur, mp-x: 300 Hz, 250 V, SRS Die mp6-AIR ist eine reguläre mp6 die speziell für die Gasförderung vermessen wurde. Bitte entnehmen Sie Informationen zu den Steuerungen und dem Zubehör den entsprechenden Datenblättern. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 18 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technische Daten der mp6-pp1 mp6-pp Typ der Pumpe Anzahl der Aktoren Abmessungen ohne Fluidanschluss Gewicht Fluidische Anschlüsse Elektrischer Anschluss Stromaufnahme selbstansaugend Pumpmedien Betriebstemperatur Lebensdauer Schutzart Material in Kontakt mit Pumpmedium Geeignete Evaluierungssteuerungen Bestellcode: mp6-pp Piezomembranpumpe 2 30 x 15 x 3,8 mm 1.1811 x 0.5906 x 0.1498 in. 2g Schlaucholiven, (Außendurchm. MIN 1,77 mm – MAX 1,85 mm, Länge 3,5 mm) 2 Flexleitung 1,25 mm Rastermaß < 200 mW ja 3 Flüssigkeiten, Gase und Gemische noch nicht definiert noch nicht definiert IP33 4 Polypropylene (PP) mp-x, mp6-EVA und mp6-OEM Typische Flussraten und Gegendrücke für bestimmte Medien (Werte bestimmt mit mp-x: 250 V, SRS): Gase max. Flussrate 14 ml/min +/- 15% (11,9 – 16,1 ml/min) 5 max. Gegendruck 150 mbar +/- 15% (127,5 – 172,5 mbar) 5 Flüssigkeiten - Wasser max. Flussrate 5 ml/min +/- 15% (4,25 – 5,75 ml/min) 6 max. Gegendruck 650 mbar +/- 15% (552,5 mbar – 747,5 mbar) 6 Flüssigkeiten - MeOH max. Flussrate 6,8 ml/min 7 max. Gegendruck 550 mbar 7 1 2 3 4 5 6 7 Typische Werte. Werte schwanken abhängig von den Anwendungsbedingungen. Technische Änderungen vorbehalten. Empfohlene Schläuche: 1,02 mm Innendurchmesser. MIN & MAX bedingt durch Spritzguss-Schrumpf. Bedingungen: Saugdruck < 10 mbar, DI-Wasser, Einstellungen mp-x: 100 Hz, 250 V, SRS, max. Förderleistung wird erst nach wenigen Minuten Betriebszeit erreicht. Kann auf IP44 angepasst werden. Bedingungen: Gase, Raumtemperatur, mp-x: 300 Hz, 250 V, SRS Bedingungen: Destilliertes Wasser, Raumtemperatur, mp-x: 100 Hz, 250 V, SRS Bedingungen: MeOH, Raumtemperatur, mp-x: 100 Hz, 250 V, SRS Bitte entnehmen Sie Informationen zu den Steuerungen und dem Zubehör den entsprechenden Datenblättern. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 19 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Technische Daten der mp51 mp5 Typ der Pumpe Anzahl der Aktoren Abmessungen ohne Fluidanschluss Gewicht Fluidische Anschlüsse Elektrischer Anschluss Stromaufnahme selbstansaugend Pumpmedien Betriebstemperatur Lebensdauer Schutzart Material in Kontakt mit Pumpmedium Geeignete Evaluierungssteuerungen Bestellcode: mp5 Piezomembranpumpe 1 14 x 14 x 3,5 mm 0.5512 x 0.5512 x 0.1378 in. 0,8 g Schlaucholiven, (Außendurchmesser 2 mm, Länge 3 mm) 2 Flexleitung / Klinkenstecker < 200 mW ja 3 Flüssigkeiten oder Gase 0–70°C 5000 h 4 IP44 Polyphenylsulphon (PPSU), Polyimid (PI), Nitrilbutadienkautschuk (NBR) 5 mp-x, mp6-EVA und mp6-OEM Typische Flussraten und Gegendrücke für bestimmte Medien (Werte bestimmt mit mp-x: 250 V, SRS): Gase (als Produkt mp6-AIR) max. Flussrate 15 ml/min (300 Hz) 6 max. Gegendruck 30 mbar (300 Hz) 6 Flüssigkeiten – Wasser max. Flussrate 5 ml/min (100 Hz) 4 max. Gegendruck 250 mbar (100 Hz) 4 1 2 3 4 5 6 Typische Werte. Werte schwanken abhängig von den Anwendungsbedingungen. Technische Änderungen vorbehalten. Empfohlene Schläuche: 1,3 mm Innendurchmesser. Bedingungen: Saugdruck < 10 mbar, DI-Wasser, Einstellungen mp-x: 100 Hz, 250 V, SRS, max. Förderleistung wird durch manuelles Befüllen erreicht. Bedingungen: Destilliertes Wasser, Raumtemperatur, mp-x: 100 Hz, 250 V, SRS Die mp5 ist nicht beständig gegen konzentrierte Alkohole wie MeOH oder EtOH. Bedingungen: Gase, Raumtemperatur, mp-x: 300 Hz, 250 V, SRS Bitte entnehmen Sie Informationen zu den Steuerungen und dem Zubehör den entsprechenden Datenblättern. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 20 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Zubehör für die Bartels Mikropumpen mp-x Steuerung Bestellcode: mp-x Zugriff auf alle leistungsbestimmenden Parameter für die professionelle Evaluierung der Mikropumpen. 7,5 x 16 x 20 cm Größe 2.983 x 6.299 x 7.874 in. Gewicht ca. 800 g Pumpmedien Flüssigkeiten, Gase mp6: 7 ml/min (SRS, 250 V, 100 Hz), DI-Wasser mp6-AIR: 18 ml/min (SRS, 250 V, 300 Hz), Luft Max. Fluss mp6-pp: 5 ml/min (SRS, 250 V, 100 Hz), DI-Wasser mp5: 5 ml/min (SRS, 250 V, 100 Hz), DI-Wasser Variable Parameter Amplitude, Frequenz, Signalform Amplitudenbereich 0 – 250 V Frequenzbereich 0 - 300 Hz Wählbare Signalform SRS, Rechteck, Sinus Stromversorgung Steckernetzteil Stromverbrauch 750 mA bei 7,5 V USB-Port inkl. Treiber Einer; eine CD mit Treibersoftware ist beigefügt mp5: 1x-2x anzuschließende oder Mikropumpen mp6, mp6-AIR bzw. mp6-pp: 1x mp6-OEM Steuerung Bestellcode: mp6-OEM Die OEM Steuerung bietet die Möglichkeit der variablen Pumpenansteuerung bei einer Größe ähnlich einem integriertem Schaltkreis zur Integration in die Systemelektronik oder auf einer Platine. 10,5 x 20,5 x 6 mm Größe 0.4134 x 0.8070 x 0.2362 in. Pumpmedien Flüssigkeiten, Gase 4,9 ml/min @ 3 VDC supply; 100 Hz Max. Fluss (mp6, DI-Wasser) 7 ml/min @ 5 VDC supply; 100 Hz Variable Parameter Amplitude, Frequenz Amplitudenbereich 85 – 270 Vpp 1 25 - 226 Hz Frequenzbereich (Frequenzen bis 1000 Hz sind möglich, doch dann sinkt die Amplitude. Frequenzen bis zu 1 Hz sind erreichbar durch einen externen Taktgenerator.) Wählbare Signalform ähnlich Rechteck 2,5 – 5,5 VDC Betriebsspannung Stromverbrauch Pin Gestaltung 1 mp-x mp6-OEM (5 V für optimale Leistung empfohlen) ca. 30 mA bei 5 V DIL 14; Horizontal ~2,54 mm, vertikal ~7,62 mm Vor Mai 2014: mp6-OEM haben einen Amplitudenbereich von 85 – 235 Vpp Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 21 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-EVA Evaluierungsboard Bestellcode: mp6-EVA Das Evaluierungsboard ermöglicht die einfache Inbetriebnahme der Mikropumpe basierend auf der mp6-OEM Steuerung. Neben voreingestellten Standardparametern (235 Vpp, 100 Hz) bietet mp6-EVA auch die Möglichkeit die Pumpenparameter flexibel, zum Teil über externe Beschaltung, einzustellen. Da das Board neben der Stromversorgungsmöglichkeit über 2,5 – 5 VDC auch über eine Spannungsversorgung per USB-Port (keine Datenverbindung) verfügt, können Sie es einfach an den PC anschließen und die an das mp6-EVA angeschlossene Pumpe testen. Größe Pumpmedien Max. Fluss (mp6, DI-Wasser) Variable Parameter Amplitudenbereich 6,5 x 3 x 2 cm 2.5590 x 1.1811 x 0.7874 in. Flüssigkeiten, Gase 4,9 ml/min @ 3 VDC supply; 100 Hz 7 ml/min @ 5 VDC supply; 100 Hz Amplitude, Frequenz 85 – 270 Vpp 1 25 - 226 Hz Frequenzbereich (Frequenzen bis 1000 Hz sind möglich, doch dann sinkt die Amplitude. Frequenzen bis zu 1 Hz sind erreichbar durch einen externen Taktgenerator.) Wählbare Signalform Stromversorgung Stromverbrauch ähnlich Rechteck via USB oder 2,5 V – 5,5 VDC ca. 30 mA bei 5 V 1 mp6-EVA Vor Mai 2014: mp6-EVA haben einen Amplitudenbereich von 85 – 235 Vpp mp6-QuadEVA Evaluierungsboard Bestellcode: mp6-QuadEVA Das mp6-QuadEVA ist ein Evaluation-Board welches ermöglicht bis zu vier mp6 Mikropumpen gleichzeitig und mit Frequenzen bis zu 800 Hz zu betreiben. Es besteht die Möglichkeit die Pumpenspannung und die Frequenz entweder direkt auf dem Board mittels der Drehschalter zu verändern, mittels Befehlen über das HyperTerminal oder über die mitgelieferte Software wenn das Board per USB an einen PC angeschlossen ist. Größe Pumpmedien Max. Fluss (mp6-AIR, Gas: Luft) Variable Parameter Amplitudenbereich Frequenzbereich Wählbare Signalform Stromversorgung Stromverbrauch 1 80 x 60 x 16 mm 3,15 x 2,36 x 0,63 in. Flüssigkeiten, Gase jede einzelne mp6-AIR: ~42 ml/min @ 260 V; 800 Hz Amplitude, Frequenz 0 – 260 Vpp 50 - 800 Hz Sinus 7.5 V, 1000 mA Durchschnitt 220 mA, Spitze 280 mA1 mp6-QuadEVA vier angeschlossene mp6-AIR @ 260 V und 800 Hz Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 22 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-con Verbindungskabel Bestellcode: mp6-con Verbindungskabel mp6/mp6-pp zu mp-x - Molex FCC 1,25 mm Rastermaß Aufbau und Anschlüsse - 85 cm Kabel - Binder 620 Stecker mp6-con mp6-mol Mikropumpenstecker Bestellcode: mp6-mol Stecker zur Kontaktierung der mp6/mp6-pp für kundeneigene Kabelkonfektionierung Molex FCC 39532045 Typ 1,25 mm Rastermaß Verpackungseinheit 10 Stück mp-cv Rückschlagventil mp6-mol Bestellcode: mp-cv Das passive Rückschlagventil verhindert den Rückfluss des Mediums, wenn die Pumpe ausgeschaltet ist. 21 mm x 5,5 mm (Länge x Schlüsselweite) Abmessungen 0.82677 x 0.2165 in. Material Silikon, Edelstahl Schlaucholive, Länge: 5,6 mm Fluidische Anschlüsse für Schlauch mit innerem Durchmesser: 1,3 mm Öffnungsdruck typisch < 35 mbar Max. Gegendruck 500 mbar Leckrate <20 µl/h für DI-Wasser (bei 500 mbar) mp-cv mp-t Schlauch Ein-/Auslass kompatibler Schlauch aus Tygon® Innendurchmesser 1,3 mm geeignet für: mp5, mp6 und mp6-AIR Bestellcode: mp-t ID1.3 mp-t Innendurchmesser 1,02 mm geeignet für: mp6-pp mp-y Schlauchverbinder Bestellcode: mp-t ID1.02 Bestellcode: mp-y Y-Schlauchverbinder für den Parallelbetrieb von zwei Mikropumpen: Material Polypropylen (PP) für innere 1,3 – 2,6 mm Schlauchdurchmesser von 0.0512 – 0.1024 in. mp-y Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 23 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 Evaluierungssets mp5-go! Set Bestellcode: mp5-go! Mit diesem Set kann mit der Evaluierung der mp5 direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp5 1 mp-x Steuerung 1 Meter mp-t ID 1.3 Schlauch mp6-go! Set Bestellcode: mp6-go! Mit diesem Set kann mit der Evaluierung der mp6 direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6 1 mp-x Steuerung 1 mp6-con 1 Meter mp-t ID1.3 Schlauch mp6-go! Set mp6-basic Set Bestellcode: mp6-basic Mit diesem Set kann mit der Evaluierung der mp6 direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6 1 mp6-EVA Evaluierungsboard 1 Meter mp-t ID1.3 Schlauch mp6-pro Set mp6-basic Set Bestellcode: mp6-pro Mit diesem Set kann die Evaluierung der mp6 auf der Systemplatine des Kunden gestartet werden. Es besteht aus: 5 Mikropumpen mp6 5 mp6-OEM 5 Stück mp6-mol 1 Meter mp-t ID1.3 Schlauch mp6-AIR-go! Set mp6-pro Set Bestellcode: mp6-AIR-go! Mit diesem Set kann mit der Evaluierung der mp6-AIR direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6-AIR 1 mp-x Steuerung 1 mp6-con 1 Meter mp-t ID1.3 Schlauch Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 24 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-AIR-basic Set Bestellcode: mp6-AIR-basic Mit diesem Set kann mit der Evaluierung der mp6-AIR direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6-AIR 1 mp6-EVA Evaluierungsboard 1 Meter mp-t ID1.3 Schlauch mp6-AIR-pro Set Bestellcode: mp6-AIR-pro Mit diesem Set kann die Evaluierung der mp6-AIR auf der Systemplatine des Kunden gestartet werden. Es besteht aus: 5 Mikropumpen mp6-AIR 5 mp6-OEM 5 Stück mp6-mol 1 Meter mp-t ID1.3 Schlauch mp6-pp-go! Set Bestellcode: mp6-pp-go! Mit diesem Set kann mit der Evaluierung der mp6-pp direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6-pp 1 mp-x Steuerung 1 mp6-con 1 Meter mp-t ID1.02 Schlauch mp6-pp-basic Set Bestellcode: mp6-pp-basic Mit diesem Set kann mit der Evaluierung der mp6-pp direkt gestartet werden. Es besteht aus: 3 Mikropumpen mp6-pp 1 mp6-EVA Evaluierungsboard 1 Meter mp-t ID1.02 Schlauch mp6-pp-pro Set Bestellcode: mp6-pp-pro Mit diesem Set kann die Evaluierung der mp6-pp auf der Systemplatine des Kunden gestartet werden. Es besteht aus: 5 Mikropumpen mp6-pp 5 mp6-OEM 5 Stück mp6-mol 1 Meter mp-t ID1.02 Schlauch Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 25 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501 mp6-QuadEVA Set Bestellcode: mp6-QuadEVA Mit diesem Set kann mit der Evaluierung der mp6 direkt gestartet werden. Es besteht aus: 4 Mikropumpen mp6 1 mp6-QuadEVA Evaluierungsboard 1 mini-USB-Kabel 1 Meter mp-t ID1.3 Schlauch mp6-AIR-QuadEVA Set mp6-QuadEVA Set Bestellcode: mp6-AIR-QuadEVA Mit diesem Set kann mit der Evaluierung der mp6-AIR direkt gestartet werden. Es besteht aus: 4 Mikropumpen mp6-AIR 1 mp6-QuadEVA Evaluierungsboard 1 mini-USB-Kabel 1 Meter mp-t ID1.3 Schlauch mp6-pp-QuadEVA Set Bestellcode: mp6-pp-QuadEVA Mit diesem Set kann mit der Evaluierung der mp6-AIR direkt gestartet werden. Es besteht aus: 4 Mikropumpen mp6-pp 1 mp6-QuadEVA Evaluierungsboard 1 mini-USB-Kabel 1 Meter mp-t ID1.02 Schlauch Das angebotene Zubehör soll Sie in Ihrem Evaluierungsprozess unterstützen. Nachdem so die Eignung der Mikropumpen für die spezielle Anwendung des Kunden geprüft wurde, kann eine entsprechende Miniaturisierung der Steuerungen vorgenommen werden. Der Entwurf von kundenspezifischen Steuerungen ist Teil des Services, den Bartels microComponents anbietet. Bitte kontaktieren Sie uns, wenn wir Ihnen bei der Auswahl des geeigneten Zubehörs behilflich sein können. Bartels Mikrotechnik GmbH, Konrad-Adenauer-Allee 11, 44263 Dortmund, Germany 26 (04.2015) rev. 2.3 www.bartels-mikrotechnik.de, [email protected] Tel: +49-231-47730-500, Fax: +49-231-47730-501