service manual fm stereo/fm

Сomentários

Transcrição

service manual fm stereo/fm
ST-S5
SERVICE MANUAL
AEP Model
UK Model
E Model
Australian Model
Ver 1.0 2001.04
ST-S5 is the tuner section
in MHC-S7AV.
SPECIFICATIONS
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
87.5 – 108.0 MHz
FM lead antenna
75 ohm unbalanced
10.7 MHz
AM tuner section
Tuning range
AEP, UK models:
Other models:
Antenna
Antenna terminals
Intermediate frequency
Dimensions (w/h/d)
Mass
531 – 1,602 kHz
(with the interval set at
9 kHz)
531 – 1,602 kHz
(with the interval set at
9 kHz)
530 – 1,710 kHz
(with the interval set at
10 kHz)
AM loop antenna
External antenna terminal
450 kHz
Approx. 280 x 108 x 340 mm
Approx. 2.1 kg
Design and specifications are subject to change
without notice.
FM STEREO/FM-AM
SUPERHETERODYNE TUNER
9-873-832-11
Sony Corporation
2001D0500-1
C 2001.4
Home Audio Company
Shinagawa Tec Service Manual Production Group
ST-S5
TABLE OF CONTENTS
1.
SERVICING NOTES ................................................ 3
2.
GENERAL
Location of Controls ....................................................... 4
Setting the Time .............................................................. 5
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
Disassembly Flow ...........................................................
Cover ...............................................................................
Front Panel Section .........................................................
PANEL Board, SIRCS Board .........................................
Tuner pack (FM/AM) ......................................................
MAIN Board ...................................................................
DSP Board .......................................................................
4.
TEST MODE .............................................................. 10
5.
DIAGRAMS
5-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
5-2. Schematic Diagram – MAIN Board (1/2) – ..................
5-3. Schematic Diagram – MAIN Board (2/2) – ..................
5-4. Printed Wiring Board – MAIN Board – ........................
5-5. Printed Wiring Board – DSP Board – ............................
5-6. Schematic Diagram – DSP Board (1/2) – .....................
5-7. Schematic Diagram – DSP Board (2/2) – .....................
5-8. Printed Wiring Boards – PANEL Section – ..................
5-9. Schematic Diagram – PANEL Section – .......................
5-10. IC Pin Function Description ...........................................
6.
6
7
7
8
8
9
9
11
12
13
14
15
16
17
18
19
21
EXPLODED VIEWS
6-1. Cover, Front Panel Section ............................................. 28
6-2. Chassis Section ............................................................... 29
7.
2
ELECTRICAL PARTS LIST ............................... 30
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ST-S5
SECTION 1
SERVICING NOTES
This set is a component of the MHC-S7AV.
The MHC-S7AV system configuration is as shown below, and
therefore it does not operate normally unless all four components
are connected.
In performing the repair, connect all components with the system
cables.
Note: The precaution to the users is described on the label stuck
on the back panel (CD player) and in the troubleshooting section
in the Operation Manual.
• MODEL IDENTIFICATION
– Rear Panel –
System Configuration:
TA
POWER SUPPLY
PART No.
AC IN
MODEL
PART No.
AEP and UK models
4-232-327-0[]
Australian model
4-232-327-1[]
Mexican model
4-232-327-4[]
Korean model
4-232-327-9[]
ST
SYSTEM & CD µcon
DISPLAY
CDP
TC
TC µcon
3
ST-S5
SECTION 2
GENERAL
This section is extracted from
instruction manual.
LOCATION OF CONTROLS
– Front Panel –
qh
wh
qjqk ql w;
wg wf
–
+
–
+
wd ws wa
CLOCK/TIMER wg (13, 21, 29)
DISPLAY qh (13, 16, 18, 29, 35)
ENTER w; (17, 18)
IR receptor wh
PRESET +/– ws (17, 18)
PTY (AEP, UK models only) wa (18)
STEREO/MONO qj (17)
TIMER SELECT wf (22, 30)
TUNER/BAND wd (17)
TUNER MEMORY qk (17)
TUNING +/– ql (17)
– Rear Panel –
1
1 ANTENNA terminal
2 SYSTEM CONTROL 1 connector (TO TA-S7AV)
3 SYSTEM CONTROL 2 connector (TO TA-S7AV)
4 SYSTEM CONTROL 3 connector (FROM CDP-S3)
5 OPTICAL IN terminal
2
6 OPTICAL IN terminal (FROM CDP-S3)
3
7 SYSTEM CONTROL 4 connector (TO TC-S3)
8 OPTICAL OUT terminal
9 SUB WOOFER OUT jack
4
5 6 7 8 9 0 qa
0 MD IN/OUT jack
qa VIDEO (AUDIO) IN jack
4
ST-S5
Setting the time
Remote Control
1
2
1 2 3
Turn on the system.
Press CLOCK/TIMER (or CLOCK/TIMER
SET on the remote).
When you set the time for the first time,
proceed to step 5.
es
ea
e;
wl
wk
wj
wh
wg
H
hH
hH
.
>
x
m
M
X
O
P
p
4
5
6
7
8
9
q;
qa
o
wf
wd
ws
wa
w;
ql
qk
CD H es (14, 15)
CHECK 5 (15)
CLEAR 6 (15)
CLOCK/TIMER SELECT qj
(30)
CLOCK/TIMER SET qk (13, 21,
29)
DBFB qg (23)
DISPLAY ws (13, 16, 18, 29, 35)
D.SKIP 4 (14)
ENTER wg (10, 12, 13, 15, 17,
18, 21, 22, 26–30)
EQ qd (27)
EQ ON/OFF qf (10, 28)
FUNCTION wf (10, 14, 15, 20,
21, 31)
GROOVE wa (23)
SET UP qs (10, 12, 26, 28, 29)
SLEEP 7 (29)
SUR wd (25)
TAPE A hH ea (19, 35)
TAPE B hH e; (19, 20, 35)
qs
qd
qf
qg
3
Press O or o repeatedly to select
“CLOCK SET”.
4
5
6
7
Press ENTER (A/V amplifier or remote).
8
Press ENTER (A/V amplifier or remote).
Press O or o repeatedly to set the hour.
Press ENTER (A/V amplifier or remote).
Press O or o repeatedly to set the
minutes.
Tip
If you have made a mistake or want to change the
time, start over from step 2.
qh
Note
qj
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
TUNER/BAND wl (17)
TUNING + 9 (17)
TUNING – wh (17)
TV CH +/– ql
TV VOL +/– w;
TV @/1 2
TV/VIDEO 1
VOL +/– qh
BUTTON DESCRIPTIONS
@/1 (power) 3
X (pause) q;
x (stop) 8
. (go back) wk
> (go forward) wj
m (rewind) wh
M (fast forward) 9
O/o/P/p qa
5
ST-S5
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. COVER
(Page 7)
6
3-3. FRONT PANEL SECTION
(Page 7)
3-5. TUNER PACK (FM/AM)
(Page 8)
3-4. PANEL BOARD,
SIRCS BOARD
(Page 8)
3-6. MAIN BOARD
(Page 9)
3-7. DSP BOARD
(Page 9)
ST-S5
Note: Follow the disassembly procedure in the numerical order given.
3-2.
COVER
3 cover
1 screw
(+BVTT3 × 6 (S))
2 two screws
(case 3 TP2)
2 two screws
(case 3 TP2)
3-3.
FRONT PANEL SECTION
1 wire (flat type) (19 core)
(CN502)
3 two claws
4 front panel section
3 two claws
3 claw
2 three screws
(BVTP3 × 8)
7
ST-S5
3-4.
PANEL BOARD, SIRCS BOARD
2 two screws
(BVTP2.6 × 8)
6 SIRCS board
4 PANEL board
2 four screws
(BVTP2.6 × 8)
5 two claws
2 screw
(BVTP2.6 × 8)
(AEP, UK models)
1 wire (flat type) (19 core)
(CN602)
3 two claws
3-5.
TUNER PACK (FM/AM)
3 tuner pack (FM/AM)
1 wire (flat type) (11 core)
(Korean, Mexican and Australian models)
wire (flat type) (15 core)
(AEP, UK models)
(CN506)
2 two screws
(BVTP3 × 8)
8
ST-S5
3-6.
MAIN BOARD
1 wire (flat type) (21 core)
(CN509)
2 five connectors
(CN510, 5031, 5032, 5041, 5042)









1 wire (flat type) (23 core)
(CN508)
6 MAIN board
4 screw
(BVTP3 × 8)
4 two screws
(BVTP3 × 8)
1 wire (flat type) (19 core)
(CN502)
3 three screws
(BVTP3 × 8)
5 PC board holder
2 connector
(CN601)
3-7.
DSP BOARD
1 wire (flat type) (23 core)
(CN603)
4 three screws
(BVTP3 × 8)
6 DSP board
1 wire (flat type) (21 core)
(CN602)
3 three screws
(BVTP3 × 8)
5 PC board holder
2 connector
(CN601)
9
ST-S5
SECTION 4
TEST MODE
Note: Use flowing buttons in the test mode.
no mark : Button of tuner unit (ST-S5)
*1
: Button of amplifier unit (TA-S7AV)
*2
: Button of CD unit (CDP-S3)
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure 1:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the [DIGITAL] * 1 button, press the
[DISPLAY] button.
3. The set is reset, and becomes standby state.
Procedure 2:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [PLAY MODE]*2 and x *2 buttons,
press the M *2 button.
3. The set is reset, and becomes standby state.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure 1:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [STEREO/MONO] and [CINEMA
STUDIO C]*1 buttons, press the [TIMER SELECT] button.
3. The set is reset, and becomes standby state.
Procedure 2:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [PLAY MODE]*2 and x *2 buttons,
press the m *2 button.
3. The set is reset, and becomes standby state.
[Change-over the AM Tuning Interval]
(EXCEPT AEP and UK models)
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the ?/1 *1 button to turn the power ON.
2. Turn the [FUNCTION] *1 knob to select “TUNER”, and press
the [TUNER/BAND] button to select the BAND “AM”.
3. Press the ?/1 *1 button to turn the power OFF.
4. While pressing the [ENTER] button, press the ?/1 *1 button,
and the display on the fluorescent indicator tube changes to
“AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning
interval is changed over.
[Change-over of VACS ON/OFF]
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [STEREO/MONO] and [CINEMA
STUDIO C]*1 buttons, press the [CINEMA STUDIO B] button,
and VACS ON/OFF is change over.
10
[GC Test Mode]
Enter the GC Test Mode mode
Procedure 1:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [STEREO/MONO] and [CINEMA
STUDIO C]*1 buttons, press the [CLOCK/TIMER] button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Procedure 2:
1. Press the ?/1 *1 button to turn the power ON.
2. While pressing the both [PLAY MODE]*2 and x *2 buttons,
press the Z (DISC 1)*2 button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Version Display Mode
Procedure:
1. Enter the GC test mode.
2. Each time the [TUNER MEMORY] or [DISC 1]*2 button is pressed,
microcomputer or mechanism deck version is displayed of each
unit.
3. Press the [TUNING +] or [DISC 3]*2 button to detail is displayed
the version.
Key Check Mode
Procedure:
1. Enter the GC test mode.
2. Press the [TUNING -- ] or [DISC 2]*2 button to set the key check
mode.
3. In the key check the mode, the fluorescent indicator tube
displays “K 0 J 0 V 0” . Each time a button is pressed, “K”
value increases. However, once a button is pressed, it is no
longer taken into account.
VACS Level Display Mode
Procedure:
1. Enter the GC test mode.
2. Press the [TUNING +] or [DISC 3]*2 button to display VACS
level on the fluorescent indicator tube.
Segment Check Mode
Procedure:
1. Enter the GC test mode.
2. Press the [ENTER] or x *2 button to set the segment check
mode.
3. In the segment check the mode. Each [ENTER] or x *2
button is pressed, the fluorescent indicator tube displays is
switching variously.
Releasing the GC Test Mode
• To release from this mode, press three buttons in the same manner
as entering this mode or disconnect the power cord.
ST-S5
SECTION 5
DIAGRAMS
5-1.
• Circuit Boards Location
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
C
Q
These are omitted.
B E
Q
B C
E
These are omitted.
Q
B
C
E
These are omitted.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
: internal component.
•
• 5 : fusible resistor.
• C : panel designation.
DSP board
TUNER PACK
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
(
) : CD PLAY
〈〈
〉〉 : AC OFF
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : TUNER (FM/AM)
E : TAPE PLAY
G : RECORD
J : CD PLAY
c : DIGITAL INPUT
N : MIC INPUT
• Abbreviation
AUS : Australian model
KR
: Korean model
MX : Mexican model
SIRCS board
MAIN board
PANEL board
11
11
ST-S5
SCHEMATIC DIAGRAM – MAIN Board (1/2) –
(1/2)
CN5031
5P
M(A)-GND
EVER+5V
NO901
3P
D-GND
NO991
3P
D+5V
C991
0.1
I
G
(Page 13)
CN5041
10P
+15V REGULATOR
O
C992
0.1
IC991
NJM7815FA
AA6
MIC-SIG
MIC-GND
(A-GND)
AA5
FL-OUT
FRONT-GND
AA4
FR-OUT
AA3
CENTER-OUT
CENTER-GND
AA2
(Page 13)
SL-OUT
S-GND
AA1
1
SR-OUT
2
3
4
OPTICAL RECEIVER
VCC
C955
10000p
OPTICAL IN
(FROM CDP-S3)
5
GND
6
R951
470
OUT
IC951
TORX178B
C957
10000p
OPTICAL RECEIVER
VCC
OPTICAL IN
GND
OUT
IC952
TORX178B
R952
470
L951
220µH
7
8
9
C964
10000p
C956
10
50V
AB21
NO507
4P
AB20
(CHASSIS)
C916
10000p
10
(Page 16)
CN510
5P
REC OUT-R
BB1
BB2
PB-R
TC A-GND
BB3
PB-L
BB4
REC OUT-L
SYSTEM CONTROL 4
CN508
23P
(TO TC-S3)
C977
10
50V
+10V REGULATOR
DD1
IC903
NJM7810FA
L955
470µH
TUNER L-IN
DD2
O
11
I
G
VCD L-IN
BB3
TC L-IN
BB4
TC REC L-OUT
A-GND
BB1
D941
1SS133T
R941
1k
D942
1SS133T
R942
1k
TC REC R-OUT
BB2
TC R-IN
DD3
VCD R5-IN
C978 10 50V
D901
D3SBA20
DD4
TUNER R-IN
C966
10000p
A+10V
AA6
C905
470
16V
C904
3300
16V
C952
4700
25V
C953
0.1
(Page 13)
C941
10
50V
R943
3.3k
MIC-IN
A-GND
AA5
FL-OUT
(Page 17)
F-GND
AA4
FR-OUT
+5V REGULATOR
A-GND
IC904
µPC7805AHF
AA2
LS-OUT
DBFB FEEDBACK
5-2.
S-GND
AA1
RS-OUT
C-GND
AA3
C-OUT
LINE-MUTE
O
I
D922
11ES2
G
D903
11ES2
C907
220
10V
C906
0.1
D904
11ES2
DBFB FEEDBACK
D923
11ES2
CN509
21P
D-GND
+7V REGULATOR
IC901
TA78057S
D-OUT
D920
11ES2-NTA2
D-GND
E8
O
DSP-DECODE
R551
470
I
D551
1SS133T-72
R555
4.7k
R552
10k
G
E7
DSP-CS
E9
12
AMP-DATA
C902
470
10V
E6
DSP-ACK
E10
AMP-CLK
E5
CODEC-SMUTE
E11
AMP-LAT
Q902
2SC2001-K1K2
RESET SIGNAL
+3.3V REGULATOR
IC551
M51943BSL
GENERATOR
E4
C553
0.1
DIR-Rx
E12
I
DIG-Tx
(Page 16)
O
R554
47k
G
E3
Q551
2SC2603
DIR-XSTATE
E13
DSP-Rx
R911
220
E2
RESET
SWITCH
DIR-CS
E14
DIG-CLK
E1
DIR-UNLOCK
C971
10000p
D-GND
D+5V
C968 10000p
A-GND
A+5V
R912
510
C970 10000p
C903
10
50V
C918
470
10V
C551
10
50V
C552
0.1
R553
47k
D552
1SS133T
13
14
15
16
17
12
12
ST-S5
5-3.
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
• See page 20 for Waveforms.
(2/2)
CN506
15P (AEP,UK)
ST-CLK
11P (E,AUS)
CL
R957 100
(AEP,UK)
ST-DIN
MC D0
ST-DOUT
MC D1
ST-CE
COAXIAL
CE
FM 75Ω
A+10V
R958 100
TUN
R959 100
STE
TUNED
FM/AM
FM
C962
10
50V
C961
0.1
R961 2.2k
TUNER
75Ω
R964
5.6k
DD1
L-CH
UNIT
ANALOG-GND
*
R962 2.2k
(E,AUS)
CN505
17P
DD4
DD2
R-CH
ST-MUTE
R963
5.6k
MUTE
VCD L-IN
AM
CD A-GND
DD3
D+5V
VCD R-IN
D902
11ES2-NTA2
N.C
RDS-INT
HAKO-GND
RDS-INT
RDS-DATA
TC M-GND
(AEP,UK)
RDS-DATA
TC M-GND
JW95
(AEP,UK)
* SUPPLIED WITH
THE ASSEMBLED
1
BLOCK
2
UNREG
TC D-GND
I-CLK
R965 100
I-DAT
R966 100
SYSTEM CONTROL 3
I2C-CLK
(FROM CDP-S3)
3
I2C-DATA
4
V-MUTE
M-RESET
5
MRESET
6
EVER+5V
CD D(M)-GND
D912
MTZJ-T72-30B
C910
10
50V
R904
10k
R903
10
D911
11ES2
-NTA2
D913
MTZJ-T-72-5.6B
R908
1k
R905
100
Q901
2SB734-3
C937
0.1
R906
100
CD D(M)-GND
D921
1SS133T-72
C915
100
35V
C909
100
50V
AB1
AC-LOW
AB2
AC-LOW
CN502
19P
DISPLAY/STANDBY KEY
-28V REGULATOR
VF
VF
-VP
D-GND
7
JOG2-B
8
JOG2-B
JOG2-A
9
JOG2-A
POWER KEY
JOG1-B
JOG1-B
JOG1-A
JOG1-A
VOLA
D943
1SS133T
R549
3.3k
VOLA
VOLB
10
VOLB
C506
4.7
50V
M-RESET
R558
1M
R550
100k
D944
1SS133T
RESET
Q502
BN1A4M
I-DAT
MUTING
I-CLK
IIC-CLK
KEY1
R524
47k
SWITCH
KEY1
Q503
BN1A4M
D+3.3V
D-GND
AC OFF
MUTING
C510
4.7
50V
D945
1SS133T
R557
22k
C942
470
6.3V
DRIVER
EVER+5V(SIRCS)
C943
0.1
SIRCS
SIRCS
R530
100
EX-IN
EX-LAT
EX-OUT
R527 100
R528 100
R556
47k
DBFB FEEDBACK
SYSTEM CONTROL 2
CN5042
9P
(TO TA-S7AV)
DBFB FEEDBACK
HAKO-GND
POWER KEY
C561
0.1
R526 100
R531 100
R533 100 E1
R534 100 E2
R535 100 E3
R536 100 E4
R537 100 E5
E6
EX-CLK
R532
47k
11
R538
100
(Page 19)
IIC-DATA
CONTROL
EPT901
POWER KEY
EX-CLK
EXP-CLK
EX-LAT
EXP-LAT
EX-OUT
R956
100
EXP-OUT DATA
EX-IN
EXP-IN DATA
KEY1
(Page 12)
UNREG
NO-USE
EXP-IN DATA
VCC
EXP-LAT
EXP-CLK
SOFT-TEST
VSS
LINE-MUTE
EXP-OUT DATA
R540
100
DISPLAY KEY
POWER KEY
DSP-DECODE
DIR-UNLOCK
E8
DIR-CS
DIR-XSTATE
DSP-CS
DIR-RX
E7
-SMUTE
CODEC
KEY0 TA
DSP-ACK
R539
100
(CHASSIS)
CN5032
15P
JOG2-B
(Page 12)
JOG2-B(F-SELECT)
JOG2-A
JOG2-A(F-SELECT)
SYSTEM CONTROL 1
JOG1-B
JOG1-A
JOG1-A(FUNCTION)
STE
R523
100
STEREO
TUN
R542 47k
VOLA
VOLA
M-RESET
VOLB
TUNED
VOLB
AB20
R522
10k
R544
4.7k
AC HIGH
AB21
M-RESET
R543
150
* R545
MODEL-IN
10k (AEP,UK)
AC HIGH
C972 0.1
AB2
C562
10000p
SYSTEM CONTROLLER
AC LOW
AB1
IC501
M30622MGA-A39FP
AC LOW
SPEC-IN
4.7k (KR,AUS)
R546
*
1k (MX)
* R546
(E,AUS)
150 (KR,AUS)
(TO TA-S7AV)
JOG1-B(FUNCTION)
R541
47k
VP
R545
*
VF
V-MUTE
VF
AVSS
CT
CC2
4.7k (MX)
NO-USE
(Page
12)
CT
CC3
C508
10
50V
VREF
NO-USE
AVCC
NO-USE
EPT902
IIC CLK
ST-DIN
ST-CLK
CC1
ST-DOUT
ST-CE
ST-MUTE
RDS-DATA
RDS-INT
NMI
VCC
XOUT
XIN
VSS
XCIN
RESET
XCOUT
CNVSS
GND
DIG-CLK
DSP-RX
DIG-TX
C509
0.1
SIRCS
CUT
R548
4.7k
AMP-LAT
AC-
12
AMP-CLK
AMP-DATA
CC4
C928
0.1
NO-USE
C927
0.1
(CHASSIS)
IIC DATA
CN503
10P
GND
CC1
TXD1/CAN'T USE
CC2
R514 100
R513 100
R512 100
(E,AUS)
R516
100
R517
100
R518
100
R519
10k
+5V
CC3
R525 100
(FOR TEST)
CLK1/SQ-CLK
CC4
R520
10k
R529 100
RXD1/SQ-DATA-IN
CC5
CNVSS
I-DAT
I-CLK
ST-CLK
ST-DIN
ST-DOUT
ST-CE
ST-MUTE
CC6
RDS-DATA
C505
1000
6.3V
RDS-INT
C504
0.1
R515
1k
JW501
JW502
R511 10k
R510 330
X502 16MHz
C502 15p
C503 0.1
R508 10k
SIRCS
C501 18p
E14
E12
E13
E11
E10
X501
R501
100
RTS1
NC
R509 330k
32.768 kHz
R507 100
R505 100
R506 100
R504 100
R502 100
R503 100
C519
100p
E9
ANTENNA
STEREO
R521 100
RESET
C520
100p
GND
CN501
4P
13
D-GND
D+5V
(FOR TEST)
I-CLK
IIC-CLK
14
CC5
CC6
I-DAT
IIC-DATA
15
16
17
(CHASSIS)
13
13
ST-S5
PRINTED WIRING BOARD – MAIN Board –
• Semiconductor
Location
2
3
5
6
7
8
Location
AM
COAXIAL
FM 75Ω
SYSTEM
CONTROL 1
(TO TA-S7AV)
* SUPPLIED WITH
THE ASSEMBLED BLOCK
FM/AM TUNER UNIT *
MAIN BOARD
(CHASSIS)
R524
R523
EPT902
EPT901
JW47
R512
R514
R537
(E, AUS)
R906
JW502
R517
JW501
R538
R511
R539
R540
JW39
C505
C504
JW32
R518
R908
D913
R519
4
CN501
(FOR TEST)
C552
D551
1
C928
E
X501
R546
(E, AUS)
JW27
C501
JW503
JW21
JW19
R548
JW55
D944
E
R558
R504
JW115
R506
JW84
1
D903
JW119
IC903
R549
Q502
JW106
D921
JW81
SYSTEM
CONTROL 3
JW100
D943
C506
JW94
D945
R557
E
JW90
10
3
C942
E
R965
1
JW113
JW96
R502
R555
JW26
C510
JW87
D901
1
R554
D552
R553
5
D922
C553
Q551
JW29
C508
JW88
JW107
D923
R552
JW30
1
CN5031
R904
R551 C551
JW80
JW920
C509
R544
IC551
R966
R941
JW958
CN5041
C962
C904
C905
D904
JW83
R545
C503
R963
C953
C520
3
R521
X502
R510
R509 C502 R508
R964
JW959
15
R543
R942
D942
C937
C910 D912 C915
R905
R520
4
D941
C927
C519
1
JW38
C972
(TO TA-S7AV)
9
R961
R943
D911
R903
SYSTEM
CONTROL 2
JW98
JW44
R516
B
JW118
IC501
R962
JW92
R535
R536
C
CN506
C941
JW25
E
1
JW116
R529
JW43
JW50
R533
R534
C909
Q901
D902
JW89
R525
1
R956
(AEP, UK)
JW91
CN5032
R513
R515
C961
R959
C562
R528
C943
D
R957
CN503
R541
C
(AEP, UK)
JW53
R532
R526
R542
1
JW104
10
R522
CN5042
JW971
R531
R556
(CHASSIS)
R958
JW921
(FOR TEST)
JW34
C561
JW108
B
R527
R530
Q503
FROM
CDP-S3
CN505
JW18
R507
JW65
JW16
R912
JW15
Q902
F
JW79
JW76
JW77
JW917
JW70
C902
E
JW14
JW78
IC901
JW28
CN502
C952
NO901
JW97
R505
C903
1
JW56
R503
C918
(Page 18)
3
3
JW952
R501
R550
JW37
PANEL
BOARD
CN602
JW13
JW17
1
D
JW35
JW68
CLP101
R911
JW71
D920
IC952
JW69
JW207
3
1
JW85
C970
JW201
JW93
CN509
IC904
C907
C968
C978
C906
JW64
C977
C971
JW75
L955
JW110
(Page 15)
DSP BOARD
CN603
C992
(Page 15)
3
3
H
SYSTEM
CONTROL 4
(TO TC-S3)
1
1
NO991
C991
(INCLUDED IN MAIN BOARD)
14
A
IC991
(FROM CDP-S3)
1
4
11
R951
NO507
B
14
1
IC951
3
OPTICAL IN
5
CN510
DSP BOARD
CN602
L951
IC951
C955
C964
1
JW111
C966
C
1
R952
CN508
IC952
C916
JW60
JW99
JW202
JW957
JW203
JW112
JW204
G
C956
JW117
JW205
3
OPTICAL IN
JW954
JW206
C957
JW62
JW208
JW86
JW918
JW209
JW956
E-3
E-4
D-4
C-5
F-4
FM
75Ω
(AEP, UK)
JW41
C-2
D-4
E-6
D-6
G-4
G-10
F-10
H-8
10
(E, AUS)
A
JW42
IC501
IC551
IC901
IC903
IC904
IC951
IC952
IC991
9
ANTENNA
JW67
D-4
D-4
C-8
C-7
E-4
E-5
C-6
C-5
C-5
F-4
E-5
D-5
D-5
C-7
C-7
E-4
E-3
E-4
JW40
D551
D552
D901
D902
D903
D904
D911
D912
D913
D920
D921
D922
D923
D941
D942
D943
D944
D945
Q502
Q503
Q551
Q901
Q902
4
JW51
Ref. No.
1
• See page 11 for Circuit Boards Location.
JW500
5-4.
1-680-695DSP BOARD
CN601
(Page 15)
(11)
ST-S5
5-5.
PRINTED WIRING BOARD – DSP Board –
1
• See page 11 for Circuit Boards Location.
2
3
4
5
6
7
8
• Semiconductor
Location
9
Ref. No.
Location
J601
VIDEO
(AUDIO)
IN
MD
A
IC609
DSP BOARD
3
(CHASSIS)
C732
R738
R734 C720
C712
C608
30
31
R640
R637
R639
R641
D
R611
R612
R613
1
12
44
R654
IC605
E
R647
R646
R765
R615
C741
R629
IC603
R664
R628
C657
C638
C636
C656
R660 R631
C653 C654
R633
R661
C701
R720
C651
R680
R655
E
C649
E
Q609
FB604
R662
R727
FB605
C721
R723
E
C703
C648
C681
R715
R649
R711
E
MAIN
BOARD
CN508
R709
C689
C699
(Page 14)
C690 Q603
R755
D606
R776
C674
C673
R651
CN603
E
C678
Q606
R652
C675
E
C700
Q607
FB606
R778 (E, AUS)
R712
C672
R759
G
B
R777
R650
4
CN601
(Page 14)
C677
R724
C691
1
A
MAIN
BOARD
NO507
C729
R784
R775
Q610
C680 C679
C676
C727
C728
R728
R717
JR601
C725
R768
C650
C652
Q602
R754
R663
JR603
E
R725
C682
IC607
Q604
C726
R729
C702
C683
R632
C687
C723
R719
FB607
R697 R700
C686
Q608
C647
Q612
E
FB608
R702
C685
E
C616
R659
R769
C684
IC606
R658
(E, AUS)
R721
C645
JR620
E
Q605
C692
C640
R656
R642
R716
C731
JR621
C641
C639
R696
C693
R665
R630
C615
R666
C637
C655
C704
C695
R701
R699
C658
D604
R676
R771
E
C635
R772
F
Q613
D605
C708
R679 C619
R683
C620
C694
C730
R610
R620 R619
R730
C621
C742
C738
R621
C644
C642
C643
R713
C707
R675
R608
C736
R674
C623
R607
R657
D609 D607
C622
R606
IC602
C607
33
R648
R643
R644
R645
D610 D608
R707
R760
R762
34
23
C705
R731
R677
R653
22
Q611
R733
R688
R605
60
C606
R636
R635
R638
11
R604
C613
61
R623
R601
R603
C614
R681
C706
R682 E
C609
R602
R686
R685
C709
R698
12
R689
C666
R634
C662
FB602
C603
C604
R687 R684
C624
R751
C724
13
C661
C716
C633
R703
48
C602
C617
C618
R706
R752
C710
1
C664 Q601
IC601
C601
R691
R673
R758
C715
R749
C739
R618
IC604
R690
R616
R617
24
C660
D601
FB601
90
C740 1
X601
25
1
C713
R750
C665
3
91
R614
36
120
C612
C625
C626
C627
37
C628
R692
C646
R670
R671
R672
E
C714
C610
JR622
C
IC610
C659
R780
R668
R669
C711
R748 R747
C611
R667
(CHASSIS)
EP603
C634
IC608
C629
R
C717
R779
C632
R678
L
C735
C630
R781
R756 R757
R
C719
1
C631
R735
L
C722
R739
R746
R
FB603
R742
R743
L
IC609
EP604
B
IN
OPTICAL
OUT
(CONDUCTOR SIDE)
DSP BOARD (COMPONENT SIDE)
OUT
J602
SUB
WOOFER
OUT
R761
C671
R695
CN602
R770
C669
R693
C670
R773
R694
EP602
R766
R763
R767
1-680-319-
(CHASSIS)
R774
11
C668
(11)
C667
11
C733
1-680-319-
C
MAIN BOARD
CN509
(Page 14)
15
15
(11)
D601
D604
D605
D607
D608
D609
D610
C-8
D-7
D-7
E-2
E-2
E-1
E-1
IC601
IC602
IC603
IC604
IC605
IC606
IC607
IC608
IC609
IC610
C-4
C-6
E-4
C-2
D-3
E-7
F-2
C-2
B-6
C-7
Q601
Q602
Q603
Q604
Q605
Q606
Q607
Q608
Q609
Q610
Q611
Q612
Q613
C-8
F-6
F-7
E-9
D-9
G-8
G-9
E-8
F-8
F-8
C-9
E-6
D-8
ST-S5
SCHEMATIC DIAGRAM – DSP Board (1/2) –
• See page 20 for Waveforms.
• See page 20 for IC Block Diagram.
1
2
R666 100
4
E2
R665 100 E1
3
C657
1000p
C656
220
10V
C655
0.1
R664
100
CN602
21P
A+5V
FB608
A-GND
R680
3.3k
FB607
DIGITAL
D+5V
FILTER,
D-GND
R630
100
F3
R629 100
R633 100
R628 100
C616
220
10V
6
IC603
TC74HCT7007AF
FB605
0
C648
220
10V
R614 100
R615 100
C649
0.1
R652
470
R651
470
R661
330
7
C652
0.1
R649
470
R650
470
D604
1SS355
C637 0.01
C638 0.01
C639 0.01
C642
0.001
C640 0.01
8
R643 330
C606
0.1
TP623
PAGE1
TP621
PAGE0
C647
220
10V
R663
470
C650
220
10V
C641 0.01
C607
0.1
C738
0.001
A1
R620
100
A2
R618
100
R616 100
R619
100
R617 100
D-OUT
+3.3V
REGULATOR
N9
C1
N8
E1
FB604
0
D-GND
D-GND
JR603
0
Q602
2SC1623
DSP-CS
DSP-DECODE
R660
330
R662
100
C615
0.1
B3
C654
0.01
R659 100
N7
AMP-DATA
C653
0.1
R658 100
D4
N10
C2
R657 100
TP619
R644 330
DSP-ACK
H2
N6
B2
H7
E2
AMP-CLK
H3
C3
F1
R645 330
CODEC-SMUTE
F2
R646 330
C2
B1
R656
10k
N5
E2
C3
AMP-LAT
R655
10k
C6
R647 330
DIG-Tx
DIR-Rx
R632 100
C5
R648 330
C4
C4
C651 0.1
C5
DIR-XSTATE
SWITCH
N4
DSP-Rx
5
CONTROL
N3
C1
DIR-CS
JR621
0
IC606
PCM1748E/2K
MUTING
LEVEL SHIFT
N2
E1
R631
100
N1
C6
DIG-CLK
(Page 12)
D/A CONVERTER
Q612
FN1F4M
DIR-UNLOCK
C636
0.01
C643
0.001
R613
100
G2
R611 100
G3
R610
100
A4
A5
R621
100
H6
R607 100
H5
R606 100
H4
R755
100
D0
A6
R605 100
H2
A7
R604 100
H1
D1
C644
0.1
9
IC605
AK4527
C635
0.1
R603
100
A9
C604
0.1
C646
0.01
SIGNAL PROCESSOR
A10
R654
10k
IC601
CXD9617R
A11
R602
1k
A12
C721
220
10V
R642
100
R653
10k
A/D,D/A CONVERTER
AUDIO DIGITAL
(Page 12)
(Page
17)
C645
220
10V
H3
A8
R754
100
C658
0.1
G1
C608
0.1
CN601
4P
D605
1SS355
H7
R608 100
JR622 0
G6
G4
R612 100
A3
A13
C603
0.1
C609
0.1
A14
G5
A15
TP622
PLOCK
A17
S-RAM
C736
0.1
C602
0.01
A16
C601
0.1
TP601 TDO
R640 100
R639 100
C740
0.1
R638 100
R601
100
TP605 TDI
R641
100
R635
100
R623
10k
TP604 TCK
R637 100
TP603
XTRST
R636 100
A14
A15
A16
A17
A1
A18
A13
A12
A11
C613
0.1
A10
A9
A8
A7
A6
A5
A2
A4
A3
A19
TP602 MS
TP614 BCK
TP615 LRCK
IC602
IS61LV6416-15T
TP618 D2
TP616
DOUT
TP617 D3
H1
H6
H5
H4
H2
BCK
H3
TP611
Q613
FA1A4M
RESET
10
SWITCH
11
R634 100
12
13
C612
0.1
C739
0.001
C742
0.001
R771
10k
14
C610
0.1
C611
0.1
FB601
0
A34
A33
A32
A31
A30
A29
A28
A27
A26
A25
A24
A23
A22
A21
A20
A19
A18
A23
A22
A21
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A20
C614
0.1
A34
5-6.
C659
220
10V
+2.6V REGULATOR
15
G
O
IC610
NJM2391DL1-26TE1
I
16
17
EP604
C735
GND
0.1
18
(CHASSIS)
19
16
16
ST-S5
5-7.
SCHEMATIC DIAGRAM – DSP Board (2/2) –
• See page 20 for Waveforms.
• See page 20 for IC Block Diagram.
1
K3
R767 1k
K1
K2
R768 10k
K8
J3
R763 1k
R765 1k
J1
R766 1k
R769 1k
R775
10k
R773 1k
R777
10k
R774 1k
C691
0.1
J2
R778
1k
J4
R776
10k
(E,AUS)
C690
220
10V
R770 1k
4
R772 1k
REGULATOR
K7
Q603
2SC1623
K9
+5V
3
K6
Q603
2
R762
1k
FB606
47
C689
100
16V
INPUT SELECT SWITCH,
GRAPHIC
EQUALIZER CONTROL,
ELECTRICAL VOLUME
IC607
M61512FP
5
R761
1k
K4
R760 1k
JR601
0
C667
10 50V
R759 1k
C668
10 50V
R758 1k
N1
C669
10 50V
N2
C670
10 50V
N3
C671
10 50V
N4
C672
10 50V
N5
C673
10 50V
C687 100 16V
N6
C674
10 50V
C686 100 16V
J5
K5
J6
N8
C676 1 50V
C728 0.1
C722
0.1
C678
N10
C692 0.1
8
C685
10
50V
R693
100
B2
R694 100
B1
R695 100
R698
470k
R703
1M
C618
0.01
D607
RB501V
M1
M2
R676 100
M3
+3.3V
R681
33k
9
R692
100
C662
0.1
C660
220
10V
C666
220
10V
C664
0.1
C661
220
10V
C620
0.1
C665
0.1
D601
RD3.9SB2
R682
100
C621
0.01
C622
0.1
C680
10 50V
R706
47k
TUNER R-IN
K9
MIC-IN
R709 D606
0
0
D608
RB501V
D610
RB501V
C730
10
50V
C681
1 50V
L1
C682
1 50V
A-GND
R715
1k
L2
L3
G3
R686 100
G4
R687 100
G5
I3
TP608 SL
LS-OUT
I4
TP609 SR
RS-OUT
I5
TP610 C
(Page 12)
S-GND
R719
1k
C-OUT
DBFB FEEDBACK
I6
R721
1k
JR620
0
TP624
A.GND
MUTING
I3
C702
1
50V
R723
1k
R725
1k
J1
Q609
2SC3624
R724
47k
L1
MUTING
I5
R727
1k
J2
R729
1k
C704
2.2
50V
R728
47k
J3
R731
4.7k
R733
1k
Q611
2SC3624
R730
22k
DIGITAL AUDIO
INVERTER
INTERFACE RECEIVER
IC608
SN74LVU04APWR
R671
100
E1
J5
R756
47k
R757
47k
M3
C716
220p
R746
10k
C715 220p
R743
10k
J601
6P
R751 47k
L
VIDEO
R742
15k
C708
10
50V
(AUDIO)
R750 12k
C714 220p
R739
15k
C707
10
50V
IN
R
L
R749 12k
IN
C713 220p
R
R738
1k
C706
10
50V
MD
R748 100k
L
C712 470p
OUT
R735
1k
R
C711 470p
J6
M2
C709
10
50V
R752
47k
MUTING
M1
R690
1M
C710
10
50V
MUTING
J4
R673
100
R691
0
10
FR-OUT
MUTING
L3
R672
100
G6
TP607 FR
C-GND
R720
47k
R674 100
IC604
LC89056W-E
R667
100
I2
Q608
2SC3624
R688 100
R689
1k
FL-OUT
LINE-MUTE
C617
0.1
C624
0.1
TP606 FL
A-GND
I4
C701
1
50V
L4
I1
F-GND
C731
0.1
L4
C683
1 50V
TP612
LRCK
TP613
DATA
TP620
BCK
R685 100
A+10V
I6
I1
C700
10
50V
(CHASSIS)
TC R-IN
VCD R5-IN
K8
Q610
2SC3624
G2
TC REC R-OUT
FEED BACK SWITCH
C703
1
50V
R684 100
K5
K7
L2
G1
TC REC L-OUT
Q604,605
R696
1.8k
R675
100
R683 100
C623
220
10V
TC L-IN
K4
(E,AUS)
C619
0.1
REGULATOR
K3
K6
R716
47k
R679
4.7k
FB603
VCD L-IN
R707
47k
Q605
2SC1623
R677
5.6k
Q601
2SD1387
TUNER L-IN
K2
A-GND
Q607
2SC3624
D609
RB501V
K1
DBFB CONTROL/
C695
0.1
EP602
GND
CN603
23P
Q606
R713
2SC3624
1k
MUTING
R712
47k
Q604
2SC1623
R701 10k
C684 10 50V
C679
0.1
R700
10k
R702
1M
R699
470k
C741
0.1
(Page
16)
C733
0.1
I2
C693
0.1
C694
0.1
FB602
0
C727
10
50V
C699 R711
10
1k
50V
10 50V
B3
C725 C726
10
0.1
50V
C724
0.1
R697 1.8k
C677 1 50V
N9
C723
10
50V
R717 1k
N7
C675 1 50V
C729
7
10 50V
6
R781
47k
R780
47k
R779
47k
C631
0.01
C705
10
50V
J602
1P
R747
100k
R734
1k
SUB
WOOFER
D1
OUT
C720
220p
C717
0.1
D0
C719
0.1
C718
NO MT
C630
0.01
EP603
GND
11
X601
13.5MHz
12
(CHASSIS)
C732
0.1
R678
10k
13
C625
10p
C626
10p
OPTICAL
C628
0.1
TRANSCEIVER
IC609
TOTX178A
14
C629
0.1
R668
100
F1
F3
C627
0.1
R669
100
C632
0.1
C633
220
10V
D.GND
OPTICAL
VCC
R670
100
15
D.OUT
F2
E2
16
17
C634
0.1
18
19
17
17
OUT
ST-S5
5-8.
PRINTED WIRING BOARDS – PANEL Section –
1
2
• See page 20 for Circuit Boards Location.
3
4
5
6
7
8
9
10
PANEL BOARD
A
C610
JW24
R603
FL601
FLUORESCENT
INDICATOR
TUBE
C601
C653
C651
C655
C657
C659
C661
C649
S611
C664
JW1
C666
STEREO/MONO
R623
R624
R625
R626
S607
S608
ENTER
S609
–
R622
PRESET
S610
TUNER MEMORY
+
R636
R637
R634
R635
R632
R633
R630
R631
R628
R620
R621
R601 R602
R639
R638
C652
C663
–
TUNING
+
TUNER/BAND
R604
C658
C660
C662
JW31
JW33
C101
CLOCK/TIMER
C614
C615
JW10
IC101
JW114
C608
C607
R677
3
JW3
JW601
JW602
JW8
S604
C656
S602
D601
S605
C654
C603
C
S606
R616
JW36
R605
R629
SIRCS
BOARD
DISPLAY
IC601
X601
JW5
JW6
B
S601
C665
C650
JW57
JW11
R617
R618
JW4
C605
S603
1
TIMER SELECT
R607
R102
R627 R619
C606
C669
(AEP, UK)
(AEP, UK)
R606
CN602
R608
JW45
S612
D
PTY
S601 – 612
D
• Semiconductor
Location
Location
D601
C-5
IC101
IC601
C-10
B-5
1
1
3
3
1-680-696-
MAIN BOARD
CN502
(Page 14)
Ref. No.
NO101
NO601
18
18
R101
1-680-697-
11
11
(11)
(11)
ST-S5
SCHEMATIC DIAGRAM – PANEL Section –
• See page 20 for Waveform.
FL601
96
101
97
98
99
1
100
2
3
4
5
6
7
8
10
9
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
43
44
45
46
47
FLUORESCENT INDICATOR TUBE
100p
100p
100p
C657
C658
C659
100p
100p
C656
C662
100p
C655
100p
100p
C654
C661
100p
C653
100p
100p
C652
C660
100p
C651
1
2
3
4
5
6
7
8
9
10
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
12
C610
10
50V
R616
100k
(AEP,UK)
S612
CN602
19P
PTY
R627
5.6k
A23
32
S611
A24
STEREO/
33
VF
VF
G7
-VP
100
G7
A25
MONO
G6
G5
G4
G3
G2
G1
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
VSS FOR IO
31
A15
A16
A17
A18
A19
A20
A21
A22
VDD FOR VFT
DISP/STANDBY KEY
D-GND
A26
S610
B2
97
B3
96
B4
JOG2-A
JOG1-B
G10
A27
JOG1-A
G11
A28
37
101
B5
VOLA
G12
A29
S609
98
JOG2-B
36
TUNER MEMORY
B1
G9
35
R626
3.9k
99
G8
34
38
R625
2.7k
B6
A30
G12
A31
G12
VOLB
39
+
RESET
40
A32
PRESET
S608
IIC-DATA
41
R624
2.2k
B8
DISPLAY CONTROLLER
A33
IIC-CLK
B9
IC601
MB90M407PF-G-102
-BND
VSS FOR IO
43
KEY1
A34
S607
D+3.3V
44
R623
1.5k
A35
D-GND
45
ENTER
S604
X601
4MHz
XOUT
RESET
C608
0.1
C664
0.1
R603
10k
NO101
3P
GND
+5V
+5V
OUT
OUT
C615 220p
B8 R605 100
C101
47
16V
IC101
GP1U28X
R101
47
R102
47
REMOTE CONTROL
B9
RECEIVER
C667
0.1
19
R608
10k
R607
10k
R606
10k
R628 10k
B6
R629
1k
B7 R604 100
C614
220p
R630 10k
R631 1k
B5
R632 10k
R633 1k
R634 10k
B4
TP607
TP606
R635 1k
B3
TP605
R637 1k
TP604
B2
R636 10k
R617
270
R638 10k
C666
47
50V
NO601
3P
GND
TP608
R639 1k
C665
47
50V
TP603
C650
10000p
B1
CLOCK/TIMER
R618
470
R677
1k
DISPLAY
TIMER SELECT
S602
SIRCS
S601
C663
10000p
R619
560
EVER+5V(SIRCS)
XIN
TUNER/BAND
S603
C669
0.1
VSS FOR CPU
KEY1
I2C DATA
I2C CLK
VOLB
VOLA
JOG1A
JOG1B
R602
10k
R620
820
JOG2A
MODE1
JOG2B
+
TP602
R601
10k
MODE2
R621
1k
C649
10000p
MODE0
S605
VCC FOR CPU
KEY0
VKK FOR VFT
TP601
TUNING
AVCC FOR ANALOG
A38
-
AVSS FOR ANALOG
A37
47
R622
1.2k
D601
1SS133T-72
A36
46
S606
(Page 13)
B7
C601
10000p
5-9.
C668
0.1
C605
10000p
19
C603
0.1
C607
100
6.3V
C606
10
50V
ST-S5
• IC Block Diagrams
– DSP Board –
1 IC601 9 (MCLK1), IC604 w; (XMCK),
wa (XOUT)
IC604
5 IC601 ws (KFSIO), IC604 qd (CKOUT)
LC89056W-E
VF
F2
F1
F0
CSFLAG
1 IC501 qa (XCOUT)
XSEL
– DSP Board –
DI
DO
ERROR
BPSYNC
ERR9P
DGND
• Waveforms
– MAIN Board –
36 35 34 33 32 31
30
29 28 27 26 25
4.4 Vp-p
2.6 Vp-p
4 Vp-p
C BIT
DETECT
CE 37
CL 38
XSEL 39
MODE0 40
74.1 ns
6 IC601 wk (LRCKI2), IC604 qg (LRCK)
DOSEL0 44
DOSEL1 45
XMODE 48
1
2 3
4
5
DOUT
DINO
DINI
DIN2
22.7 µs
3 IC601 ql (LRCKO), IC605 5 (LRCK),
IC606 3 (LRCK (I))
PLL
INPUT
CIRCUIT
DISEL
3.9 Vp-p
74.1 ns
62.5 ns
TIMING
CKSEL0 46
CKSEL1 47
4.6 Vp-p
2.7 Vp-p
DATA
DEMODULATOR
6 7
8 9 10
11 12
AVDD
AGND
2 IC601 qf (SCKOUT)
7 IC601 wl (BCKI2), IC604 qf (BCK)
IC605
AK4527
LOOP1
LOOP0/SDA/CDTI
DIF1/SCL/CCLK
DIF0/CSN
P/SN
MCLK
DZF1
AVSS
AVDD
VREFH
VCOM
4 Vp-p
3.8 Vp-p
44 43 42 41 40 39 38 37 36 35 34
354 ns
– PANEL Board –
22.7 µs
4 IC601 w; (BCKO), IC605 4 (BCK),
IC606 1 (BCK (I))
1 IC601 id (XOUT)
SDOS
I2C
SMUTE
BICK
LRCK
SDTI1
SDTI2
SDTI3
8 IC606 qh (MCLK (I))
3.7 Vp-p
3.5 Vp-p
3.6 Vp-p
INPUT
CIRCUIT
1
2
3
4
5
6
7
8
AUDIO
INTERFACE
OUTPUT
CIRCUIT
SDTO 9
DAUX 10
DFS 11
FORMAT
CONVERTER
DEM1
DEM0
TVDD
DVDD
DVSS
PDN
ICKS2
ICKS1
ICKS0
CAD1
CAD0
12 13 14 15 16 17 18 19 20 21 22
74.1 ns
250 ns
22
21
20
19
18
17
16
15
14
13
X’ TAL
R
VIN
LPF
2 IC501 qd (XOUT)
LOCK
DETECT
DGND
DVDD
30.5 µs
SAMPLING
FREQUENCY
MICROCOMPUTER
INTERFACE
MODE1 41
DGND 42
DVDD 43
88.6 ns
24 AUDIO
23 EMPHA
PA/PB
DETECT
354 ns
20
20
33
32
31
30
29
28
27
26
25
24
23
DZF2
RIN+
RIN–
LIN+
LIN–
ROUT1
LOUT1
ROUT2
LOUT2
ROUT3
LOUT3
XIN
XOUT
XMCK
DVDD
DGND
XSTATE
DATAO
LRCK
BCK
CKOUT
ST-S5
5-10.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 M30622MGA-A39FP (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
AMP-DATA
O
Serial data output to the M61512FP (IC607)
2
AMP-CLK
O
Serial data transfer clock signal output to the M61512FP (IC607)
3
AMP-LAT
O
Serial data latch pulse signal output to the M61512FP (IC607)
4
SIRCS
I
Remote control signal input from the remote control receiver (IC101)
5
DIG-TX
O
Serial data output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital
filter (IC606)
6
DSP-RX
I
Serial data input from the digital audio interface receiver (IC604)
7
DIG-CLK
O
Serial data transfer clock signal output to the CXD9617R (IC601), digital audio interface receiver
(IC604) and digital filter (IC606)
8
GND
—
Ground terminal
9
CNVSS
—
Not used
10
XCIN
I
Sub system clock input terminal (32.768 kHz)
11
XCOUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC551) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
XOUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
XIN
I
16
VCC
—
17
NMI
I
Non-maskable interrupt input terminal Fixed at “H” in this set
18
RDS-INT
I
Serial data transfer clock signal from the RDS decoder on the FM/AM tuner unit
19
—
—
20
RDS-DATA
I
Serial data input from the RDS decoder on the FM/AM tuner unit
21
ST-MUTE
O
Tuner muting on/off control signal output to the FM/AM tuner unit “L”: muting on
22
ST-CE
O
Chip enable signal output to the FM/AM tuner unit
23
ST-DOUT
O
Serial data output to the FM/AM tuner unit
24
—
—
Not used (open)
25
ST-DIN
I
26
—
—
Not used (open)
27
ST-CLK
O
Serial data transfer clock signal output to the FM/AM tuner unit
28
—
—
Not used (open)
29
IIC CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the display
controller (IC601) and CDP-S3
Main system clock input terminal (16 MHz)
Power supply terminal (+5V)
Not used (open)
Serial data input from the FM/AM tuner unit
30
IIC DATA
I/O
Communication data bus with the display controller (IC601) and CDP-S3
31 to 34
NO-USE
—
Not used
35 to 40
—
—
Not used (open)
41
M-RESET
O
Reset signal output to the display controller (IC601) “L”: reset
42 to 50
—
—
Not used (open)
51
NO-USE
—
Not used
52 to 57
—
—
Not used (open)
58
EXP-IN DATA
I
Serial data input from the I/O expander in the TA-S7AV
59
EXP-OUT DATA
O
Serial data output to the I/O expander in the TA-S7AV
60
EXP-LAT
O
Serial data latch pulse signal output to the I/O expander in the TA-S7AV
61
EXP-CLK
O
Serial data transfer clock signal output to the I/O expander in the TA-S7AV
62
VCC
—
63
SOFT-TEST
I
Power supply terminal (+5V)
Soft test output terminal Not used (open)
21
ST-S5
Pin No.
Pin Name
I/O
Description
64
VSS
—
Ground terminal
65 to 70
—
—
Not used (open)
71
LINE-MUTE
O
Audio line muting on/off control signal output to the audio line circuit “L”: muting on
72
—
—
Not used (open)
73
DISPLAY KEY
I
DISPLAY switch (S601) input terminal
74
POWER KEY
I
Power on/off switch in the TA-S7AV input terminal
75
DIR-UNLOCK
I
PLL lock error and data error flag input from the digital audio interface receiver (IC604)
76
DIR-CS
O
Chip enable signal output to the digital audio interface receiver (IC604)
77
DIR-XSTATE
I
Source clock switching monitor input from the digital audio interface receiver (IC604)
78
DIR-RX
I
Read data input from the digital audio interface receiver (IC604)
79
CODEC-SMUTE
O
Soft muting on/off control signal output to the A/D, D/A converter (IC605) “L”: muting on
80
DSP-ACK
I
Acknowledge signal input from the CXD9617R (IC601)
81
DSP-CS
O
Chip select signal output to the CXD9617R (IC601)
82
DSP-DECODE
O
Decode signal input from the CXD9617R (IC601)
83 to 86
—
—
Not used (open)
87
STEREO
I
FM stereo detection signal input from the FM/AM tuner unit “L”: stereo
Tuning detection signal input from the FM/AM tuner unit “L”: tuned
88
TUNED
I
89 to 91
—
—
92
MODEL-IN
I
Model setting terminal
93
SPEC-IN
I
Specification setting terminal
94
—
—
Not used (open)
95
V-MUTE
O
Video muting on/off control signal output terminal “L”: muting on Not used (open)
96
AVSS
—
Ground terminal
97
—
—
Not used (open)
98
VREF
I
99
AVCC
—
100
AC-CUT
I
22
Not used (open)
Reference voltage (+5V) input terminal
Power supply terminal (+5V)
AC cut on/off detection signal input from the reset signal generator (IC551)
“L”: AC cut on, “H”: AC cut off or checked
ST-S5
• DSP BOARD IC601 CXD9617R (AUDIO DIGITAL SIGNAL PROCESSOR)
Pin No.
Pin Name
I/O
Description
1
VSS
—
2
XRST
I
Reset signal input from the M61512FP (IC607) “L”: reset
3
EXTIN
I
Master clock signal input terminal
4
FS2
I
Sampling frequency selection signal input terminal
5
VDDI
—
Ground terminal
Not used (fixed at “L”)
Not used (fixed at “L”)
Power supply terminal (+2.6V)
6
FS1
I
Sampling frequency selection signal input terminal
7
PLOCK
O
Internal PLL lock signal output terminal
8
VSS
—
Ground terminal
9
MCLK1
I
10
VDDI
—
Power supply terminal (+2.6V)
11
VSS
—
Ground terminal
12
MCLK2
O
Oscillation clock signal output terminal
Not used (fixed at “L”)
Not used (open)
Oscillation clock signal input from the digital audio interface receiver (IC604)
Not used (open)
13
MS
I
Master/slave selection signal input terminal “L”: slave, “H”: master (fixed at “L” in this set)
14
SCKOUT
O
Internal system clock signal output to the digital filter (IC606)
15
LRCKI1
I
L/R sampling clock signal (44.1 kHz) input terminal
16
VDDE
—
Not used (open)
Power supply terminal (+3.3V)
17
BCKI1
I
Bit clock signal (2.8224 MHz) input terminal
18
SDI1
I
Audio serial data input from the D/A, A/D converter (IC605)
19
LRCKO
O
L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter
(IC606)
20
BCKO
O
Bit clock signal (2.8224 MHz) output to the D/A, A/D converter (IC605) and digital filter (IC606)
Not used (open)
21
VSS
—
22
KFSIO
I
Audio clock signal input from the digital audio interface receiver (IC604)
23 to 25
SDO1 to SDO3
O
Audio serial data output to the A/D, D/A converter (IC604)
26
SDO4
O
Audio serial data output to the digital filter (IC606)
Ground terminal
27
SPDIF
O
S/PIDF signal output terminal
28
LRCKI2
I
L/R sampling clock signal (44.1 kHz) input from the digital audio interface receiver (IC604)
29
BCKI2
I
Bit clock signal (2.8224 MHz) input from the digital audio interface receiver (IC604)
30
SDI2
I
Audio serial data input from the digital audio interface receiver (IC604)
31
VSS
—
Ground terminal
32
HACN
O
Acknowledge signal output to the system controller (IC501)
33
HDIN
I
Write data input from the system controller (IC501)
Not used (open)
34
HCLK
I
Clock signal input from the system controller (IC501)
35
HDOUT
O
Read data output to the system controller (IC501)
36
HCS
I
Chip select signal input from the system controller (IC501)
37
SDCLK
O
Clock signal output terminal
38
CLKEN
O
Clock enable signal output terminal
39
RAS
O
Row address strobe signal input terminal
40
VDDI
—
Power supply terminal (+2.6V)
Not used (open)
Not used (open)
Not used (open)
41
VSS
—
Ground terminal
42
CAS
O
Column address strobe signal output terminal
43
DQM
O
Output terminal of data input/output mask
Chip select signal output to the S-RAM (IC602)
Not used (open)
Not used (open)
44
CS0
O
45
WE0
O
Write enable signal output to the S-RAM (IC602)
46
VDDE
—
Power supply terminal (+3.3V)
47
WMD1
I
S-RAM wait mode setting terminal
Fixed at “H” in this set
23
ST-S5
Pin No.
Pin Name
I/O
Description
48
VSS
—
49
WMD0
I
S-RAM wait mode setting terminal Fixed at “L” in this set
50
PAGE2
O
Page selection signal output terminal Not used (open)
51
VSS
—
Ground terminal
52, 53
PAGE1, PAGE0
O
Page selection signal output terminal Not used (open)
54
BOOT
I
Boot mode control signal output terminal Not used (fixed at “L”)
55
BTACT
I
Boot mode state display signal output terminal Not used (open)
Ground terminal
56
BST
I
Boot trap signal input from the M61512FP (IC607)
57
MOD1
I
PLL input frequency select terminal
58
MOD0
I
Mode setting terminal
59
EXLOCK
I
PLL lock error and data error flag input from the digital audio interface receiver (IC604)
“L”: 384fs, “H”: 256fs (fixed at “H” in this set)
“L”: single chip mode, “H”: use prohibition (fixed at “L” in this set)
60
VDDI
—
Power supply terminal (+2.6V)
61
VSS
—
Ground terminal
62, 63
A17, A16
O
Address signal output terminal Not used (open)
64 to 66
A15 to A13
O
Address signal output to the S-RAM (IC602)
67
GP10
O
L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter
(IC606)
68
DECODE
O
Decode signal output to the system controller (IC501)
69
AUDIO
I
Bit 1 input terminal of channel status from the digital audio interface receiver (IC604)
70
VDDI
—
Power supply terminal (+2.6V)
71
VSS
—
Ground terminal
72 to 75
D15 to D12
I/O
Two-way data bus with the S-RAM (IC602)
76
VDDE
—
Power supply terminal (+3.3V)
77 to 80
D11 to D8
I/O
Two-way data bus with the S-RAM (IC602)
81
VSS
—
Ground terminal
82 to 85
A9, A12 to A10
O
Address signal output to the S-RAM (IC602)
86
TDO
O
Simple emulation data output terminal Not used (open)
87
TMS
I
Simple emulation data input start/end detection signal input terminal Not used (open)
88
XTRST
I
Simple emulation asychronous break input terminal Not used (open)
89
TCK
I
Simple emulation clock signal input terminal Not used (open)
90
TDI
I
Simple emulation data input terminal Not used (open)
91
VSS
—
Ground terminal
92 to 97
A8 to A3
O
Address signal output to the S-RAM (IC602)
98, 99
D7, D6
I/O
Two-way data bus with the S-RAM (IC602)
100
VDDI
—
Power supply terminal (+2.6V)
101
VSS
—
Ground terminal
102 to 105
D5 to D2
I/O
Two-way data bus with the S-RAM (IC602)
106
VDDE
—
Power supply terminal (+3.3V)
107, 108
D1, D0
I/O
Two-way data bus with the S-RAM (IC602)
109, 110
A2, A1
O
Address signal output to the S-RAM (IC602)
111
VSS
—
Ground terminal
112
A0
O
Address signal output to the S-RAM (IC602)
113
PM
I
PLL reset signal input from the M61512FP (IC607) “L”: reset
114, 115
SDI3, SDI4
I
Audio serial data input terminal Not used (fixed at “L”)
116
SYNC
I
Synchronous/asychronous selection signal input terminal
“L”: Synchronous, “H”: asynchronous (fixed at “H” in this set)
117 to 119
VSS
—
Ground terminal
120
VDDI
—
Power supply terminal (+2.6V)
24
ST-S5
• DSP BOARD IC604 LC89056W-E (DIGITAL AUDIO INTERFACE RECEIVER)
Pin No.
Pin Name
I/O
Description
1
DISEL
I
Selection terminal of data input terminal Fixed at “L” in this set
2
DOUT
O
Digital data output to the optical transceiver (IC609)
3
DIN0
I
Digital data input from the optical receiver (IC952) (for CDP-S3)
4
DIN1
I
Digital data input from the optical receiver (IC951) (for external input)
5
DIN2
I
Digital data input terminal Not used (fixed at “L”)
6
DGND
—
Ground terminal (digital system)
7
DVDD
—
Power supply terminal (+3.3V) (digital system)
8
R
I
VCO gain control input terminal
9
VIN
I
VCO free run frequency setting input terminal
10
LPF
O
PLL loop filter setting output terminal
11
AVDD
—
Power supply terminal (+3.3V) (analog system)
12
AGND
—
Ground terminal (analog system)
13
CKOUT
O
Audio clock signal output to the CXD9617R (IC601)
14
BCK
O
Bit clock signal (2.8224 MHz) output to the CXD9617R (IC601)
15
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the CXD9617R (IC601)
16
DATAO
O
Audio serial data output to the CXD9617R (IC601)
17
XSTATE
O
Source clock switching monitor output to the system controller (IC501)
18
DGND
—
Ground terminal (digital system)
19
DVDD
—
Power supply terminal (+3.3V) (digital system)
20
XMCK
O
Oscillation clock signal output to the CXD9617R (IC601)
21
XOUT
O
System clock output terminal (13.5 MHz)
System clock input terminal (13.5 MHz)
22
XIN
I
23
EMPHA
O
Emphasis information of channel status output terminal Not used (open)
24
AUDIO
O
Bit 1 output terminal of channel status to the CXD9617R (IC601)
25
CSFLAG
O
Top 40 bit renovation flag output terminal of channel status Not used (open)
26 to 28
F0 to F2
O
Input frequency calculation result output terminal Not used (open)
29
VF
O
Validity flag output terminal Not used (open)
30
DVDD
—
Power supply terminal (+3.3V) (digital system)
31
DGND
—
Ground terminal (digital system)
32
ERR9P
O
Nine times continuance data transmission error flag output terminal Not used (open)
33
BPSYNC
O
Non-PCM burst and preamble sync signal output terminal Not used (open)
34
ERROR
O
PLL lock error and data error flag output to the system controller (IC501)
35
DO
O
Read data output to the system controller (IC501)
36
DI
I
Write data input from the system controller (IC501)
37
CE
I
Chip enable signal input from the system controller (IC501)
38
CL
I
Clock signal input from the system controller (IC501)
39
XSEL
I
Selection input terminal of vibrator frequency terminal Fixed at “H” in this set
40
MODE0
I
Mode setting input terminal Fixed at “H” in this set
41
MODE1
I
Mode setting input terminal Fixed at “H” in this set
42
DGND
—
Ground terminal (digital system)
43
DVDD
—
Power supply terminal (+3.3V) (digital system)
44
DOSEL0
I
Output data format selection signal input terminal Fixed at “L” in this set
45
DOSEL1
I
Output data format selection signal input terminal Fixed at “L” in this set
46
CKSEL0
I
Output clock selection signal input terminal Fixed at “L” in this set
47
CKSEL1
I
Output clock selection signal input terminal Fixed at “L” in this set
48
XMODE
I
System reset signal input from the M61512FP (IC607)
25
ST-S5
• DSP BOARD IC605 AK4527 (A/D, D/A CONVERTER)
Pin No.
Pin Name
I/O
Description
1
SDOS
I
Audio serial data source selection signal input terminal
“L”: internal ADC output, “H”: DAUX input (fixed at “L” in this set)
2
I2C
I
Serial control mode selection signal input terminal “L”: 3-wire serial, “H”: I2C bus
3
SMUTE
I
Soft muting on/off signal input from the system controller (IC501) “L”: muting on
4
BICK
I
Bit clock signal (2.8224 MHz) input from the CXD9617R (IC601)
5
LRCK
I
L/R sampling clock (44.1 kHz) signal input from the CXD9617R (IC601)
6 to 8
SDTI1 to SDIT3
I
Audio serial data input from the CXD9617R (IC601)
9
SDTO
O
Audio serial data output to the CXD9617R (IC601)
10
DAUX
I
Audio serial data input terminal Not used (fixed at “L”)
11
DFS
I
Double speed sampling mode signal input terminal
“L”: normal speed, “H”: double speed (fixed at “L” in this set)
12
DEM1
I
De-emphasis signal input terminal Fixed at “L” in this set
De-emphasis signal input terminal Fixed at “H” in this set
13
DEM0
I
14
TVDD
—
Power supply terminal (+5V) (for output buffer )
15
DVDD
—
Power supply terminal (+5V) (digital system)
16
DVSS
—
Ground terminal (digital system)
17
PDN
I
Power down and reset signal input from the M61512FP (IC607) “L”: power down and reset
I
Input clock signal selection terminal Fixed at “L” in this set
Chip address signal input terminal Not used (fixed at “L”)
18 to 20 ICKS2 to ICKS0
21, 22
CAD1, CAD0
I
23
LOUT3
O
Analog signal output for center to the M61512FP (IC607)
24
ROUT3
O
Analog signal output for sub woofer to the M61512FP (IC607)
25
LOUT2
O
Analog signal output for surround L-ch to the M61512FP (IC607)
26
ROUT2
O
Analog signal output for surround R-ch to the M61512FP (IC607)
27
LOUT1
O
Analog signal output for front L-ch to the M61512FP (IC607)
28
ROUT1
O
Analog signal output for front R-ch to the M61512FP (IC607)
29
LIN–
I
L-ch analog signal negative input from the M61512FP (IC607)
30
LIN+
I
L-ch analog signal positive input from the M61512FP (IC607)
31
RIN–
I
R-ch analog signal negative input from the M61512FP (IC607)
32
RIN+
I
R-ch analog signal positive input from the M61512FP (IC607)
33
DZF2
O
Zero input detection terminal
34
VCOM
O
Common voltage output terminal
Large external capacitor is used to reduce power supply noise
35
VREFH
I
Reference voltage (+5V) input terminal
36
AVDD
—
Power supply terminal (+5V) (analog system)
37
AVSS
—
Ground terminal (analog system)
38
DZF1
O
Zero input detection terminal
39
MCLK
I
Master clock signal input from the CXD9617R (IC601)
40
P/S
I
Parallel/serial selection signal input terminal
“L”: serial control mode, “H”: parallel control mode (fixed at “H” in this set)
41
DIF0
I
Audio data interface format terminal Fixed at “L” in this set
42
DIF1
I
Audio data interface format terminal Fixed at “H” in this set
43, 44
LOOP0, LOOP1
I
Loop back mode setting terminal Fixed at “L” in this set
26
Not used (open)
Not used (open)
ST-S5
• PANEL BOARD IC601 MB90M407PF-G-102-BND (DISPLAY CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 6
G6 to G1
O
Grid drive signal output to the fluorescent indicator tube (FL601)
7 to 10
A1 to A4
O
Segment drive signal output to the fluorescent indicator tube (FL601)
11
VSS FOR IO
—
Ground terminal (for I/O)
12 to 22
A5 to A15
O
Segment drive signal output to the fluorescent indicator tube (FL601)
23
VDD FOR VFT
—
Power supply terminal (+3.3V) (for VFT)
24 to 41
A16 to A33
O
Segment drive signal output to the fluorescent indicator tube (FL601)
42
VSS FOR IO
—
Ground terminal (for I/O)
43 to 47
A34 toA38
O
Segment drive signal output to the fluorescent indicator tube (FL601)
48
VKK FOR VFT
—
Power supply terminal (–28V) (for VFT)
49
MODE0
—
Chip mode selection terminal
Not used (fixed at “H”)
50
MODE1
—
Chip mode selection terminal
Not used (fixed at “H”)
51
MODE2
—
Chip mode selection terminal
Not used (fixed at “L”)
52
JOG2B
I
Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (B phase input)
53
JOG2A
I
Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (A phase input)
54
JOG1B
I
Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (B phase input)
55
JOG1A
I
Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (A phase input)
56
VOLA
I
Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (A phase input)
57
VOLB
I
Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (B phase input)
58, 59
—
—
Not used (open)
60
I2C DATA
I/O
Communication data bus with the system controller (IC501) and CDP-S3
61
I2C CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the system
controller (IC501) and CDP-S3
62
AVCC FOR
ANALOG
—
Power supply terminal (+3.3V) (for analog)
63
AVSS FOR
ANALOG
—
Ground terminal (for analog)
64
KEY0
I
Key input terminal (A/D input) CLOCK/TIMER, TIMER SELECT, TUNER/BAND, TUNING
+/–, ENTER, PRESET +/–, TUNER MEMORY, STEREO/MONO, PTY (S602 to S612) keys
input PTY (S612) key: Used for the AEP and UK models only
65
KEY1
I
Key input terminal for TA-S7AV (A/D input)
66 to 76
—
—
77
RESET
I
Not used (open)
Reset signal input from the system controller (IC501) “L”: reset
78 to 80
—
—
Not used (open)
81
VSS FOR CPU
—
Ground terminal (for CPU)
82
XIN
I
System clock input terminal (4 MHz)
83
XOUT
O
System clock output terminal (4 MHz)
84
VCC FOR CPU
—
Power supply terminal (+3.3V)
85 to 91
—
—
Not used (open)
92 to 94
G12
O
Grid drive signal output to the fluorescent indicator tube (FL601)
95 to 98
G11 to G8
O
Grid drive signal output to the fluorescent indicator tube (FL601)
99, 100
G7
O
Grid drive signal output to the fluorescent indicator tube (FL601)
27
ST-S5
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Abbreviation
AUS : Australian model
KR : Korean model
MX : Mexican model
6-1. COVER, FRONT PANEL SECTION
8
#2
7
5
4
1
6
5
7
3
AEP, UK
5
2
#1
Ref. No.
Part No.
Description
1
1
2
3
4
X-4953-451-1
X-4953-452-1
1-773-114-11
4-232-351-01
1-680-697-11
PANEL ASSY (ST), FRONT (AEP, UK)
PANEL ASSY (ST), FRONT (KR, MX, AUS)
WIRE (FLAT TYPE) (19 CORE)
FILTER (FL)
SIRCS BOARD
5
4-951-620-01 SCREW (2.6X8), +BVTP
28
Remark
Ref. No.
Part No.
Description
Remark
6
6
7
8
#1
A-4476-267-A
A-4476-269-A
3-363-099-21
4-233-134-31
7-685-646-79
PANEL BOARD, COMPLETE (AEP, UK)
PANEL BOARD, COMPLETE (KR, MX, AUS)
SCREW (CASE 3 TP2)
COVER
SCREW +BVTP 3X8 TYPE2 N-S
#2
7-685-871-01 SCREW +BVTT 3X6 (S)
ST-S5
6-2. CHASSIS SECTION
56
55
54
#1
57
#1
#1
#1
53
63
#1
58
52
#1
(Including
not supplied
A)
#1
#1
A
59
61
60
51
62
not supplied
not supplied
Ref. No.
Part No.
Description
* 51
52
52
52
53
4-924-098-01
A-2007-939-A
A-4476-193-A
A-4476-203-A
A-4476-199-A
HOLDER, PC BOARD
MAIN BOARD, COMPLETE (MX)
MAIN BOARD, COMPLETE (AEP, UK)
MAIN BOARD, COMPLETE (KR, AUS)
DSP BOARD, COMPLETE (AEP, UK)
53
53
54
55
56
A-4476-646-A
A-4726-352-A
1-757-599-11
1-757-600-11
1-757-629-11
DSP BOARD, COMPLETE (MX)
DSP BOARD, COMPLETE (KR, AUS)
WIRE (FLAT TYPE) (21 CORE)
WIRE (FLAT TYPE) (23 CORE)
CORD (WITH CONNECTOR) 5P
57
58
1-757-631-11 CORD (WITH CONNECTOR) 20P
1-757-630-11 CORD (WITH CONNECTOR) 19P
Remark
Ref. No.
Part No.
Description
Remark
59
59
59
59
60
4-232-327-01
4-232-327-11
4-232-327-41
4-232-327-91
1-769-940-11
PANEL (ST), BACK (AEP, UK)
PANEL (ST), BACK (AUS)
PANEL (ST), BACK (MX)
PANEL (ST), BACK (KR)
WIRE (FLAT TYPE) (11 CORE) (KR, MX, AUS)
60
61
61
61
62
1-773-004-11
1-693-529-11
1-693-531-71
1-693-538-11
4-965-822-01
WIRE (FLAT TYPE) (15 CORE) (AEP, UK)
TUNER PACK (FM/AM) (AEP, UK)
TUNER PACK (FM/AM) (MX, AUS)
TUNER PACK (FM/AM) (KR)
FOOT
63
#1
3-970-608-01 SUMITITE (B3), +BV
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
29
ST-S5
SECTION 7
ELECTRICAL PARTS LIST
DSP
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
AUS : Australian model
KR : Korean model
MX : Mexican model
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
A-4476-199-A DSP BOARD, COMPLETE (AEP, UK)
A-4476-646-A DSP BOARD, COMPLETE (MX)
A-4726-352-A DSP BOARD, COMPLETE (KR, AUS)
********************
< CAPACITOR >
C601
C602
C603
C604
C606
1-164-156-11
1-162-970-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
0.1uF
0.1uF
C607
C608
C609
C610
C611
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C612
C613
C614
C615
C616
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.1uF
0.1uF
0.1uF
220uF
25V
25V
25V
25V
10V
C617
C618
C619
C620
C621
1-164-156-11
1-162-970-11
1-164-156-11
1-164-156-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
0.1uF
0.01uF
C622
C623
C624
C625
C626
1-164-156-11
1-126-934-11
1-164-156-11
1-162-915-11
1-162-915-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220uF
0.1uF
10PF
10PF
C627
C628
C629
C630
C631
1-164-156-11
1-164-156-11
1-164-156-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.01uF
C632
C633
C634
C635
C636
1-164-156-11
1-126-934-11
1-164-156-11
1-164-156-11
1-162-970-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220uF
0.1uF
0.1uF
0.01uF
C637
C638
C639
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF
0.01uF
0.01uF
30
10%
20%
10%
10%
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
0.5PF
0.5PF
25V
10V
25V
50V
50V
10%
10%
25V
25V
25V
25V
25V
20%
10%
25V
10V
25V
25V
25V
10%
10%
10%
25V
25V
25V
20%
Ref. No.
Part No.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Description
Remark
C640
C641
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF
0.01uF
10%
10%
25V
25V
C642
C643
C644
C645
C646
1-162-971-11
1-162-971-11
1-164-156-11
1-126-934-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001uF
0.001uF
0.1uF
220uF
0.01uF
10%
10%
50V
50V
25V
10V
25V
C647
C648
C649
C650
C651
1-126-934-11
1-126-934-11
1-164-360-11
1-126-934-11
1-164-360-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
220uF
220uF
0.1uF
220uF
0.1uF
20%
20%
C652
C653
C654
C655
C656
1-164-360-11
1-162-970-11
1-162-970-11
1-164-360-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.01uF
0.01uF
0.1uF
220uF
C657
C658
C659
C660
C661
1-162-971-11
1-164-156-11
1-126-934-11
1-126-934-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.001uF
0.1uF
220uF
220uF
220uF
C662
C664
C665
C666
C667
1-164-156-11
1-164-156-11
1-164-156-11
1-126-934-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
C668
C669
C670
C671
C672
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
C673
C674
C675
C676
C677
20%
10%
20%
10%
10%
20%
10%
10V
10V
16V
10V
16V
16V
25V
25V
16V
10V
20%
20%
20%
50V
25V
10V
10V
10V
0.1uF
0.1uF
0.1uF
220uF
10uF
20%
20%
25V
25V
25V
10V
50V
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
10uF
10uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
1-126-964-11
1-126-964-11
1-126-193-11
1-126-193-11
1-126-193-11
ELECT
ELECT
ELECT CHIP
ELECT CHIP
ELECT CHIP
10uF
10uF
1uF
1uF
1uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C678
C679
C680
C681
C682
1-126-964-11
1-164-156-11
1-126-964-11
1-126-193-11
1-126-193-11
ELECT
CERAMIC CHIP
ELECT
ELECT CHIP
ELECT CHIP
10uF
0.1uF
10uF
1uF
1uF
20%
20%
20%
20%
50V
25V
50V
50V
50V
C683
1-126-193-11 ELECT CHIP
1uF
20%
50V
ST-S5
DSP
Ref. No.
Part No.
Description
C684
C685
C686
C687
1-126-964-11
1-126-964-11
1-126-933-11
1-126-933-11
ELECT
ELECT
ELECT
ELECT
10uF
10uF
100uF
100uF
20%
20%
20%
20%
50V
50V
16V
16V
Remark
C689
C690
C691
C692
C693
1-126-933-11
1-126-934-11
1-164-156-11
1-136-165-00
1-136-165-00
ELECT
ELECT
CERAMIC CHIP
MYLAR
MYLAR
100uF
220uF
0.1uF
0.1uF
0.1uF
20%
20%
5%
5%
16V
10V
25V
50V
50V
C694
C695
C699
C700
C701
1-136-165-00
1-136-165-00
1-126-964-11
1-126-964-11
1-126-193-11
MYLAR
MYLAR
ELECT
ELECT
ELECT CHIP
0.1uF
0.1uF
10uF
10uF
1uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
C702
C703
C704
C705
C706
1-126-960-11
1-126-960-11
1-126-961-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
1uF
1uF
2.2uF
10uF
10uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C707
C708
C709
C710
C711
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
1-162-962-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
10uF
10uF
10uF
10uF
470PF
20%
20%
20%
20%
10%
50V
50V
50V
50V
50V
C712
C713
C714
C715
C716
1-162-962-11
1-162-957-11
1-162-957-11
1-162-957-11
1-162-957-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
220PF
220PF
220PF
220PF
10%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C717
C719
C720
C721
C722
1-164-156-11
1-164-156-11
1-162-957-11
1-126-934-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.1uF
220PF
220uF
0.1uF
C723
C724
C725
C726
C727
1-126-964-11
1-164-156-11
1-126-964-11
1-164-156-11
1-126-964-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
10uF
0.1uF
10uF
0.1uF
10uF
C728
C729
C730
C731
C732
1-164-156-11
1-126-964-11
1-126-964-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.1uF
0.1uF
C733
C735
C736
C738
C739
1-164-156-11
1-164-156-11
1-164-156-11
1-164-357-11
1-164-357-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.001uF
0.001uF
C740
C741
C742
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-164-357-11 CERAMIC CHIP
0.1uF
0.1uF
0.001uF
5%
20%
20%
20%
20%
20%
20%
25V
25V
50V
10V
25V
50V
25V
50V
25V
50V
25V
50V
50V
25V
25V
5%
5%
25V
25V
25V
50V
50V
5%
25V
25V
50V
< CONNECTOR >
CN601
CN602
CN603
1-506-469-11 PIN, CONNECTOR 4P
1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P
1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
Ref. No.
Part No.
Description
Remark
< DIODE/RESISTOR >
D601
D604
D605
D606
D607
8-719-158-02
8-719-988-61
8-719-988-61
1-216-864-11
8-719-058-24
DIODE RD3.9SB2
DIODE 1SS355TE-17
DIODE 1SS355TE-17
METAL CHIP
0
5%
DIODE RB501V-40TE-17 (E, AUS)
D608
D609
D610
8-719-058-24 DIODE RB501V-40TE-17 (E, AUS)
8-719-058-24 DIODE RB501V-40TE-17 (E, AUS)
8-719-058-24 DIODE RB501V-40TE-17 (E, AUS)
1/16W
< GROUND TERMINAL >
* EP602
* EP603
* EP604
1-537-738-21 TERMINAL, EARTH
1-537-738-21 TERMINAL, EARTH
1-537-738-21 TERMINAL, EARTH
< FERRITE BEAD/RESISTOR >
FB601
FB602
FB603
FB604
FB605
1-216-864-11
1-216-864-11
1-500-445-21
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
FERRITE
METAL CHIP
METAL CHIP
0
0
0uH
0
0
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
FB606
FB607
FB608
1-216-805-11 METAL CHIP
1-500-445-21 FERRITE
1-500-445-21 FERRITE
47
0uH
0uH
5%
1/16W
< IC >
IC601
IC602
IC603
IC604
IC605
8-759-698-76
8-759-827-81
8-759-238-47
8-759-825-15
8-759-657-47
IC
IC
IC
IC
IC
CXD9617R
IS61LV6416-15T (T&R)
TC74HCT7007AF (EL)
LC89056W-E
AK4527
IC606
IC607
IC608
IC609
IC610
8-759-825-13
8-749-018-85
8-759-549-25
8-749-923-04
8-759-835-63
IC
IC
IC
IC
IC
PCM1748E/2K
M61512FP
SN74LVU04APWR
TOTX178A (OPTICAL OUT)
NJM2391DL1-26-TE1
< JACK >
J601
J602
1-774-411-11 JACK, PIN 6P (VIDEO (AUDIO) IN, MD IN/OUT)
1-774-785-11 JACK, PIN 1P (SUB WOOFER OUT)
< JUNPER RESISTOR >
JR601
JR603
JR620
JR621
JR622
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< TRANSISTOR >
Q601
Q602
Q603
Q604
Q605
8-729-801-93
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1387
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
Q606
Q607
Q608
Q609
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
31
ST-S5
DSP
Ref. No.
Part No.
Description
Remark
Q610
8-729-141-73 TRANSISTOR
2SC3624A-T1L15L16
Q611
Q612
Q613
8-729-141-73 TRANSISTOR
8-729-113-69 TRANSISTOR
8-729-113-14 TRANSISTOR
2SC3624A-T1L15L16
FN1F4M-M32
FA1A4M-T1L33
< RESISTOR >
R601
R602
R603
R604
R605
1-216-809-11
1-216-821-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R606
R607
R608
R610
R611
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R612
R613
R614
R615
R616
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R617
R618
R619
R620
R621
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R623
R628
R629
R630
R631
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R632
R633
R634
R635
R636
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R637
R638
R639
R640
R641
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R642
R643
R644
R645
R646
1-216-809-11
1-216-815-11
1-216-815-11
1-216-815-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
330
330
330
330
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R647
R648
R649
R650
R651
1-216-815-11
1-216-815-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
330
470
470
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R652
R653
R654
R655
R656
1-216-817-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R657
1-216-809-11 METAL CHIP
100
5%
1/16W
32
Ref. No.
Part No.
Description
R658
R659
R660
R661
1-216-809-11
1-216-809-11
1-216-815-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
330
330
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
Remark
R662
R663
R664
R665
R666
1-216-809-11
1-216-817-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
470
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R667
R668
R669
R670
R671
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R672
R673
R674
R675
R676
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R677
R678
R679
R680
R681
1-216-830-11
1-216-833-11
1-216-829-11
1-216-827-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5.6K
10K
4.7K
3.3K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R682
R683
R684
R685
R686
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R687
R688
R689
R690
R691
1-216-809-11
1-216-809-11
1-216-821-11
1-216-857-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
1K
1M
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R692
R693
R694
R695
R696
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-824-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
1.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R697
R698
R699
R700
R701
1-216-824-11
1-216-853-11
1-216-853-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.8K
470K
470K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R702
R703
R706
R707
R709
1-216-857-11
1-216-857-11
1-216-841-11
1-216-841-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
1M
47K
47K
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R711
R712
R713
R715
R716
1-216-821-11
1-216-841-11
1-216-821-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
1K
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R717
R719
R720
R721
1-216-821-11
1-216-821-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
47K
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
ST-S5
DSP
Ref. No.
Part No.
Description
Remark
R723
1-216-821-11 METAL CHIP
1K
5%
1/16W
R724
R725
R727
R728
R729
1-216-841-11
1-216-821-11
1-216-821-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
1K
47K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R730
R731
R733
R734
R735
1-216-837-11
1-216-829-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
4.7K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R738
R739
R742
R743
R746
1-216-821-11
1-216-835-11
1-216-835-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
15K
15K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R747
R748
R749
R750
R751
1-216-845-11
1-216-845-11
1-216-834-11
1-216-834-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
12K
12K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R752
R754
R755
R756
R757
1-216-841-11
1-216-809-11
1-216-809-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100
100
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R758
R759
R760
R761
R762
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R763
R765
R766
R767
R768
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R769
R770
R771
R772
R773
1-216-821-11
1-216-821-11
1-216-833-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R774
R775
R776
R777
R778
1-216-821-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
(E, AUS)
Ref. No.
Part No.
MAIN
Description
Remark
A-2007-939-A MAIN BOARD, COMPLETE (MX)
A-4476-193-A MAIN BOARD, COMPLETE (AEP, UK)
A-4476-203-A MAIN BOARD, COMPLETE (KR, AUS)
*********************
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR >
R779
R780
R781
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
47K
47K
47K
5%
5%
5%
1/16W
1/16W
1/16W
< VIBRATOR >
X601
1-579-993-21 VIBRATOR, CERAMIC (13.5MHz)
**************************************************************
C501
C502
C503
C504
C505
1-162-205-31
1-162-203-31
1-164-159-11
1-164-159-11
1-126-916-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
18PF
15PF
0.1uF
0.1uF
1000uF
5%
5%
C506
C508
C509
C510
C519
1-126-963-11
1-126-964-11
1-164-159-11
1-126-963-11
1-162-282-31
ELECT
ELECT
CERAMIC
ELECT
CERAMIC
4.7uF
10uF
0.1uF
4.7uF
100PF
C520
C551
C552
C553
C561
1-162-282-31
1-126-964-11
1-164-159-11
1-164-159-11
1-164-159-11
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
100PF
10uF
0.1uF
0.1uF
0.1uF
10%
20%
50V
50V
50V
50V
50V
C562
C902
C903
C904
C905
1-162-306-11
1-126-935-11
1-126-964-11
1-126-936-11
1-126-935-11
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.01uF
470uF
10uF
3300uF
470uF
30%
20%
20%
20%
20%
16V
10V
50V
16V
16V
C906
C907
C909
C910
C915
1-164-159-11
1-126-934-11
1-126-968-11
1-126-964-11
1-126-948-11
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.1uF
220uF
100uF
10uF
100uF
20%
20%
20%
20%
50V
10V
50V
50V
35V
C916
C918
C927
C928
C937
1-162-306-11
1-126-935-11
1-164-159-11
1-164-159-11
1-164-159-11
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.01uF
470uF
0.1uF
0.1uF
0.1uF
30%
20%
16V
10V
50V
50V
50V
C941
C942
C943
C952
C953
1-126-964-11
1-126-935-11
1-164-159-11
1-128-548-11
1-164-159-11
ELECT
ELECT
CERAMIC
ELECT
CERAMIC
10uF
470uF
0.1uF
4700uF
0.1uF
20%
20%
50V
6.3V
50V
25V
50V
C955
C956
C957
C961
C962
1-162-306-11
1-126-964-11
1-162-306-11
1-164-159-11
1-126-964-11
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
0.01uF
10uF
0.01uF
0.1uF
10uF
30%
20%
30%
20%
16V
50V
16V
50V
50V
C964
C966
C968
C970
C971
1-162-306-11
1-162-306-11
1-162-306-11
1-162-306-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
30%
30%
30%
30%
30%
16V
16V
16V
16V
16V
C972
C977
C978
C991
C992
1-164-159-11
1-126-964-11
1-126-964-11
1-164-159-11
1-164-159-11
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
0.1uF
10uF
10uF
0.1uF
0.1uF
20%
20%
20%
20%
10%
20%
20%
20%
50V
50V
50V
50V
6.3V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
33
ST-S5
MAIN
Ref. No.
Part No.
Description
Remark
CN502
* CN505
Ref. No.
Q902
< CONNECTOR >
CN506
CN506
CN508
1-784-780-11 CONNECTOR, FFC 19P
1-569-624-11 SOCKET, CONNECTOR 17P
(SYSTEM CONTROL 3)
1-568-830-11 CONNECTOR, FFC 11P (E, AUS)
1-784-776-11 CONNECTOR, FFC 15P (AEP, UK)
1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CN509
CN510
CN5031
CN5032
CN5041
1-779-289-11
1-794-569-11
1-794-569-11
1-691-907-11
1-580-176-11
CONNECTOR, FFC (LIF (NON-ZIF)) 21P
PIN, CONNECTOR 5P
PIN, CONNECTOR 5P
PIN, CONNECTOR 15P
PIN, CONNECTOR 10P
Part No.
Description
8-729-011-92 TRANSISTOR
Remark
2SC2001TP-K1K2
< RESISTOR >
R501
R502
R503
R504
R505
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R506
R507
R508
R509
R510
1-247-807-31
1-247-807-31
1-249-429-11
1-247-891-00
1-249-411-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
10K
330K
330
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R511
R512
R513
R514
R515
1-249-429-11
1-247-807-31
1-247-807-31
1-247-807-31
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
100
100
100
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R516
R517
R518
R519
R520
1-247-807-31
1-247-807-31
1-247-807-31
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R521
R522
R523
R524
R525
1-247-807-31
1-249-429-11
1-247-807-31
1-249-437-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
10K
100
47K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R526
R527
R528
R529
R530
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R531
R532
R533
R534
R535
1-247-807-31
1-249-437-11
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
47K
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R536
R537
R538
R539
R540
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R541
R542
R543
R544
R545
1-249-437-11
1-249-437-11
1-249-407-11
1-249-425-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
150
4.7K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
(MX)
R545
1-249-425-11 CARBON
4.7K
5%
R545
1-249-429-11 CARBON
10K
5%
R546
1-249-407-11 CARBON
150
5%
R546
1-249-425-11 CARBON
4.7K
5%
R548
1-249-425-11 CARBON
4.7K
5%
1/4W
(KR, AUS)
1/4W
(AEP, UK)
1/4W
(KR, AUS)
1/4W
(MX)
1/4W
* CN5042 1-568-419-11 PIN, CONNECTOR 9P
< DIODE >
D551
D552
D901
D902
D903
8-719-911-19
8-719-911-19
8-719-500-56
8-719-024-99
8-719-024-99
DIODE
DIODE
DIODE
DIODE
DIODE
1SS199-25
1SS199-25
D3SBA20
11ES2-NTA2B (AEP, UK)
11ES2-NTA2B
D904
D911
D912
D913
D920
8-719-024-99
8-719-024-99
8-719-110-72
8-719-109-89
8-719-024-99
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2-NTA2B
11ES2-NTA2B
RD30ESB2
RD5.6ESB2
11ES2-NTA2B
D921
D922
D923
D941
D942
8-719-911-19
8-719-024-99
8-719-024-99
8-719-911-19
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
1SS199-25
11ES2-NTA2B
11ES2-NTA2B
1SS199-25
1SS199-25
D943
D944
D945
8-719-911-19 DIODE 1SS199-25
8-719-911-19 DIODE 1SS199-25
8-719-911-19 DIODE 1SS199-25
< GROUND TERMINAL >
EPT901 1-537-770-21 TERMINAL BOARD, GROUND
EPT902 1-537-770-21 TERMINAL BOARD, GROUND
< IC >
IC501
IC551
IC901
IC903
IC904
8-759-827-45
8-759-635-63
8-759-158-62
8-759-656-35
8-759-039-69
IC
IC
IC
IC
IC
M30622MGA-A39FP
M51943BSL
TA78057S
NJM7810FA
uPC7805AHF
IC951
IC952
IC991
8-749-923-05 IC TORX178B (OPTICAL IN)
8-749-923-05 IC TORX178B (OPTICAL IN)
8-759-982-15 IC RC7815FA
< COIL >
L951
L955
1-414-193-41 INDUCTOR
1-410-682-31 INDUCTOR
220uH
470uH
< TRANSISTOR >
Q502
Q503
Q551
Q901
34
8-729-422-57
8-729-422-57
8-729-620-05
8-729-140-97
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN4111
UN4111
2SC2603-EF
2SB734-34
ST-S5
MAIN
Ref. No.
Part No.
Description
R549
R550
R551
R552
R553
1-247-843-11
1-249-441-11
1-249-413-11
1-249-429-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
100K
470
10K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
Remark
R554
R555
R556
R557
R558
1-249-437-11
1-249-407-11
1-249-437-11
1-249-433-11
1-247-903-00
CARBON
CARBON
CARBON
CARBON
CARBON
47K
4.7K
47K
22K
1M
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
0 R903
R904
R905
R906
R908
1-219-153-11
1-249-429-11
1-247-807-31
1-247-807-31
1-249-417-11
FUSIBLE
CARBON
CARBON
CARBON
CARBON
10
10K
100
100
1K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
R911
R912
R941
R942
R943
1-249-409-11
1-249-442-11
1-249-417-11
1-249-417-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
510
1K
1K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R951
R952
R956
R957
R958
1-249-413-11
1-249-413-11
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
470
470
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R959
R961
R962
R963
R964
1-247-807-31
1-249-421-11
1-249-421-11
1-249-426-11
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
2.2K
2.2K
5.6K
5.6K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R965
R966
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
1/4W
1/4W
Ref. No.
Part No.
PANEL
Description
Remark
C653
C654
1-162-282-31 CERAMIC
1-162-282-31 CERAMIC
100PF
100PF
10%
10%
50V
50V
C655
C656
C657
C658
C659
1-162-282-31
1-162-282-31
1-162-282-31
1-162-282-31
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100PF
100PF
100PF
100PF
100PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C660
C661
C662
C663
C664
1-162-282-31
1-162-282-31
1-162-282-31
1-162-306-11
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100PF
100PF
100PF
0.01uF
0.1uF
10%
10%
10%
30%
50V
50V
50V
16V
50V
C665
C666
C667
C668
C669
1-126-963-11
1-126-963-11
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
4.7uF
4.7uF
0.1uF
0.1uF
0.1uF
20%
20%
50V
50V
50V
50V
50V
< CONNECTOR >
CN602
1-784-741-11 CONNECTOR, FFC 19P
< DIODE >
D601
8-719-911-19 DIODE 1SS199-25
< FLUORESCENT INDICATOR TUBE >
FL601
< IC >
IC601
< VIBRATOR >
X501
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
X502
1-781-107-21 VIBRATOR, CERAMIC (16MHz)
**************************************************************
A-4476-267-A PANEL BOARD, COMPLETE (AEP, UK)
A-4476-269-A PANEL BOARD, COMPLETE (KR, MX, AUS)
**********************
4-232-328-01 HOLDER, FL TUBE
4-949-935-41 CUSHION (FL)
< CAPACITOR >
C601
C603
C605
C606
C607
1-162-306-11
1-164-159-11
1-162-306-11
1-124-261-00
1-126-382-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
0.01uF
0.1uF
0.01uF
10uF
100uF
C608
C610
C614
C615
C649
1-164-159-11
1-124-261-00
1-162-286-31
1-162-286-31
1-162-306-11
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
C650
C651
C652
1-162-306-11 CERAMIC
1-162-282-31 CERAMIC
1-162-282-31 CERAMIC
30%
20%
20%
16V
50V
16V
50V
16V
0.1uF
10uF
220PF
220PF
0.01uF
20%
10%
10%
30%
50V
50V
50V
50V
16V
0.01uF
100PF
100PF
30%
10%
10%
16V
50V
50V
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
30%
1-518-744-11 TUBE, FLUORESCENT INDICATOR
8-759-828-68 IC MB90M407PF-G-102-BND
< RESISTOR >
R601
R602
R603
R604
R605
1-249-429-11
1-249-429-11
1-249-429-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R606
R607
R608
R616
R617
1-249-429-11
1-249-429-11
1-249-429-11
1-249-441-11
1-249-410-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
100K
270
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R618
R619
R620
R621
R622
1-249-413-11
1-249-414-11
1-249-416-11
1-249-417-11
1-249-418-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
560
820
1K
1.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R623
R624
R625
R626
R627
1-249-419-11
1-249-421-11
1-249-422-11
1-249-424-11
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
2.2K
2.7K
3.9K
5.6K
5%
5%
5%
5%
5%
R628
R629
R630
R631
R632
1-249-429-11
1-249-417-11
1-249-429-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1K
10K
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
(AEP, UK)
1/4W
1/4W
1/4W
1/4W
1/4W
35
ST-S5
PANEL
Ref. No.
SIRCS
Part No.
Description
Remark
R633
R634
R635
R636
R637
1-249-417-11
1-249-429-11
1-249-417-11
1-249-429-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
10K
1K
10K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R638
R639
R677
1-249-429-11 CARBON
1-249-417-11 CARBON
1-249-417-11 CARBON
10K
1K
1K
5%
5%
5%
1/4W
1/4W
1/4W
< SWITCH >
S601
S602
S603
S604
S605
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
SWITCH, TACTILE (DISPLAY)
SWITCH, TACTILE (CLOCK/TIMER)
SWITCH, TACTILE (TIMER SELECT)
SWITCH, TACTILE (TUNER/BAND)
SWITCH, TACTILE (TUNING +)
S606
S607
S608
S609
S610
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
SWITCH, TACTILE (TUMIMG –)
SWITCH, TACTILE (ENTER)
SWITCH, TACTILE (PRESET –)
SWITCH, TACTILE (PRESET +)
SWITCH, TACTILE (TUNER MEMORY)
S611
S612
1-771-410-21 SWITCH, TACTILE (STEREO/MONO)
1-771-410-21 SWITCH, TACTILE (PTY) (AEP, UK)
< VIBRATOR >
X601
1-577-358-21 VIBRATOR, CERAMIC (4MHz)
**************************************************************
1-680-697-11 SIRCS BOARD
************
< CAPACITOR >
C101
1-124-589-11 ELECT
47uF
20%
16V
< IC >
IC101
8-749-011-05 IC GP1U28X (REMOTE CONTROL RECEIVER)
< RESISTOR >
R101
1-249-401-11 CARBON
47
5%
1/4W
R102
1-249-401-11 CARBON
47
5%
1/4W
***********************************************************
MISCELLANEOUS
**************
2
54
55
56
57
1-773-114-11
1-757-599-11
1-757-600-11
1-757-629-11
1-757-631-11
WIRE (FLAT TYPE) (19 CORE)
WIRE (FLAT TYPE) (21 CORE)
WIRE (FLAT TYPE) (23 CORE)
CORD (WITH CONNECTOR) 5P
CORD (WITH CONNECTOR) 20P
58
60
60
61
61
1-757-630-11
1-769-940-11
1-773-004-11
1-693-529-11
1-693-531-71
CORD (WITH CONNECTOR) 19P
WIRE (FLAT TYPE) (11 CORE) (KR, MX, AUS)
WIRE (FLAT TYPE) (15 CORE) (AEP, UK)
TUNER PACK (FM/AM) (AEP, UK)
TUNER PACK (FM/AM) (MX, AUS)
61
1-693-538-11 TUNER PACK (FM/AM) (KR)
36
Ref. No.
Part No.
Description
Remark
ST-S5
MEMO
37
ST-S5
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.0
Date
2001.04
Description of Revision
New

Documentos relacionados

mhc-gt111/gt222

mhc-gt111/gt222 O diodo laser da unidade óptica é sensível a descargas eletroestáticas podendo vir a ser danificado por descargas causadas por roupas ou mesmo pelo corpo humano. Durante o reparo tenha cuidado para...

Leia mais