OPEN IO Modul CAN-BUS C-AO4H / C
Transcrição
OPEN IO Modul CAN-BUS C-AO4H / C
OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 OPEN IO Modul mit CAN-Bus. Ausführungen mit 4 analogen Spannungsausgängen (0 ... 10 V DC). Das Modul ist mit oder ohne Handbedienebene erhältlich (siehe Tabelle Typenübersicht). OPEN IO module with CAN-Bus. Version with 4 analog voltage outputs (0 ... 10 V DC). The module is available with or without manual control. (see table type overview). © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . DS-C-AO4H DS-C-AO4 Anwendung / Einsatzgebiet Application / Operational area Die OPEN IO Module der Serie DS-C-xxxxx sind mit einer CAN-Bus Schnittstelle ausgerüstet und können an alle OPEN EMS Controller angeschlossen werden. Die Einsatzgebiete der OPEN IO Module sind vielfältig. Insbesondere können die OPEN IO Module in Heizungs-, Lüftungsoder Klimaanlagen der Gebäudeautomation eingesetzt werden. Die OPEN IO Module sind sowohl für den Einbau im Schaltschrank als auch für den dezentralen Einsatz direkt in der Feldebene ausgelegt. Darüber hinaus können sie auch für Licht- und Jalousiesteuerungen verwendet werden. Je nach Typ eines OPEN IO Modules erfassen sie digitale oder analoge Eingangswerte von Ereignissen und Sensoren oder sie steuern über digitale und analoge Ausgänge die Feldebene. The OPEN IO modules of the series DS-C-xxxxx are equipped with a CAN-Bus interface and can be connected to all OPEN EMS controller. Typenübersicht / Bestellhinweise Type overview / order notes The operational areas of the OPEN IO modules are various. In particular the OPEN IO modules can be installed in heating, ventilation and air conditioning systems in the building automation. The OPEN IO modules are designed for the installation in the control panel as well as for the decentralized application directly in the field level. Furthermore they can be used for light- and blind control. Depending on the type of a OPEN IO module they record digital or analog input values of events and sensors or they control via digital and analog outputs the field level. Artikel Typ Article Type DS-390043 DS-C-AO4 CAN-Bus OPEN IO Modul mit 4 anlogen Eingängen. DS-390043 DS-C-AO4 CAN-Bus OPEN IO module with 4 analog inputs. DS-390044 DS-C-AO4H CAN-Bus OPEN IO Modul mit 4 anlogen Eingängen und Handbedienebene (Taster). DS-390044 DS-C-AO4H CAN-Bus OPEN IO module with 4 analog inputs and manual control (taster). Zubehör Accessory Artikel Typ Article Type DS-390024 DS-PKM Koppelmodul mit Abschlusswiderstand DS-390024 DS-PKM Coupler module with terminating resistor DS-390019 DS-BBS 10 Brückenbusstecker für OPEN IO Module (1 VE = 10 Stück) DS-390019 DS-BBS 10 Bridge bus connector for OPEN IO modules (1 PU = 10 pieces) DS-390020 DS-BBS 100 Brückenbusstecker für OPEN IO Module (1 VE = 100 Stück) DS-390020 DS-BBS 100 Bridge bus connector for OPEN IO modules (1 PU = 100 pieces) DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 1 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Sicherheitshinweis Safety guidelines ! Der Umgang mit diesem Gerät darf nur durch entsprechend geschultes Personal erfolgen, das berechtigt ist, Arbeiten an elektrischen Anlagen auszuführen. Die Geräte dürfen nicht in Verbindung mit Geräten benutzt werden, die direkt oder indirekt menschlichen, gesundheits- oder lebenssichernden Zwecken dienen oder durch deren Betrieb Gefahren für Menschen, Tiere oder Sachwerte entstehen können. Das Gerät muss außer Betrieb gesetzt werden, wenn ein gefahrloser Betrieb (z.B. sichtbare Beschädigungen) nicht mehr gewährleistet ist. Der Garantieanspruch erlischt beim Öffnen des Gerätes. Elektrischer Anschluss Die Geräte sind für den Betrieb an Kleinspannung ausgelegt. Beim elektrischen Anschluss der Geräte sind die techn. Daten zu berücksichtigen. Die Geräte müssen bei einer konstanten Betriebsspannung betrieben werden. Strom-/Spannungsspitzen beim Ein-/Ausschalten der Versorgungsspannung müssen bauseits vermieden werden. Die Versorgungs- und Signalleitungen müssen nach dem aktuellen Stand der Technik angeschlossen und verlegt werden. Insbesondere sind bei der Verlegung von Sensorleitungen mögliche Störeinkopplungen durch parallel verlaufende Fremdleitungen zu vermeiden. Für die Verlegung der CAN-Bus Leitungen ist auf die Einhaltung der Spezifikationen für den Aufbau eines CAN-Bus-Systems zu achten. © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Montagehinweise Die Montage ist nach gültigen Installationsstandards durch geschultes Personal auszuführen. Die Montage der Geräte erfolgt auf Standard-(Norm) Hutschiene 35 mm in Schaltschränken. Bei der Festlegung des Montageortes ist zu beachten, dass die Grenzen der Betriebstemperatur nicht überschritten werden. Für die Montage in Zwischendecken sind geeignete Gehäuse vorzusehen. Nötigenfalls sind Revisionsöffnungen einzuplanen. Bei der Montage ist darauf zu achten, dass die offenen Teile des Gerätes frei von Verschmutzungen sind - insbesondere kann das Gerät durch Eindringen von Metallspänen zerstört werden. Hinweis: Bei Verwendung von Schraubklemmen, darf das maximale Anzugsmoment der Schraubklemmen 0,4 Nm nicht übersteigen. Das Überschreiten des max. Anzugsmomentes kann zur Zerstörung der Klemme führen. Dadurch kann der elektrische Kontakt an der Klemme nicht mehr gewährleistet werden. DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ ! Handling with this equipment may take place only through trained personnel, who is entitled to implement work on electrical system. The devices may not be used in connection with devices which serve directly or indirectly human health or life-securing purposes or which can arise danger for humans, animals or material assets. The device must be set out of service, if a safe operation (e.g. visible damages) is no longer possible. With an interference into the equipment the warranty claim expires! Electric connection The devices are appropriate for the operation at low voltage. During the electrical connection of the devices, the technical data of the devices are valid. The devices must be operated during a constant operating voltage. Current/voltage peaks when switching on/off of the supply voltage must be avoided on site. The supply- and signal lines must be connected and laid according the current state of the art. In particular possible interference couplings have to be avoided by parallel running foreign lines with the transfer of sensor lines. For the transfer of the CAN-Bus lines it is important to pay attention to the adherence of the specifications for the structure of a CAN-Bus system. Mounting advices The assembly is to be implemented after installation standards by trained personnel. The assembly of the devices takes place on standard (norm) DIN rail 35 mm in cabinets. When defining the assembly place it should be noted that the limits of the operating temperatures are not exceeded. For the assembly in intermediate ceilings suitable housings have to be planned. If necessary, inspection openings have to be planned. When assembling it is important to be certain, that the open parts of the device are free from pollution - in particular the device can be destroyed by penetratoin of metal chips. Note: By using screw terminals the maximum torque of the screw terminals may not exceed 0.4 Nm. The exceeding of the max. torque can lead to the destruction of the terminal. Thus the electrical contact at the terminal cannot be ensured no more. +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 2 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Inbetriebnahme Commissioning Voraussetzung für die Inbetriebnahme ist die ordnungsgemäße Installation aller elektrischen Versorgungs-, Schalt- und Messleitungen. Vor dem Einschalten der Betriebsspannung ist diese auf richtigen Anschluss zu prüfen. A condition for commissioning is the normal installation of all electrical supply- , switch and measuring lines. Before switching on the operating voltage the correct connection has to be assured. Anschlussmöglichkeiten Connection possibilities Die OPEN IO Module sind für den Einsatz im gebäudetechnischen Umfeld ausgelegt. Die digitalen und analogen Eingänge der OPEN IO Module können mit branchenüblichen Sensoren beschaltet werden. Die Spezifikationen der Sensoren können den jeweiligen Datenblättern entnommen werden. The OPEN IO modules are appropriate for the application in the building technology environment. The digital and analog inputs of the OPEN IO modules can be wired with customary sensors. The specifications of the sensors can be extracted from the respective data sheets. © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . OPEN IO Modul CAN-BUS C-AO4H / C-AO4 DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 3 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Technische Daten Technical data Gehäuse: Housing: •Abmessungen (BxTxH): 54 mm x 60 mm x 90 (98) mm •Material: Kunststoff •Montage: auf Standard-Hutschiene 35 mm •Schutzart: IP 20 •Kühlung: lüfterlos durch Konvektion •Temperaturbereich: 0..50 °C •Anschluss: abziehbare Federzugklemmen Nennquerschnitt 1,5 mm² •Adress-Schalter zur Einstellung der Bus-Adresse •LED zur Betriebsanzeige •LED zur Anzeige des Bus-Zustands •Einbaulage: beliebig •Dimensions (WxDxH): 54 mm x 60 mm x 90 (98) mm •Material: Plastic •Mounting: on Standard mounting rail 35 mm •Protection class: IP 20 •Cooling: no fan ; by convection •Temperature range: 0..50 °C •Connection: removable spring terminals Nominal wire 1,5 mm² •Address-switch for setting the Bus-address •LED for operating display •LED for signalling of the bus status •Mounting position: optional Spannungsversorgung: Power supply: •Eingangsspannung: •Eingangsstrom: •Leistungsaufnahme: •max. Vorsicherung: •Schutzbeschaltung: •Input voltage: •Input current: •Power consumption: •max. back-up fuse: •Protective circuit: U(nenn) = 24 V DC (19 .. 30 V DC) I(nenn) = ca. 100 mA ca. 2,5 W 2A Verpolungsschutz der Eingangsspannung Mikroprozessor und Speicher: •CPU: •Schnittstellen: ARM7 Architektur 1x CAN-Bus © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Kommunikation: •CAN-Bus: CAN 2.0B, galvanisch getrennt ISO 11898 •Übertragungsrate: 10 kbit/s...250 kbit/s, voreingestellt 50 kbit/s •Busleitung: CAN-Bus Leitung, Wellenwiderstand RW = 120 Ohm •Busabschlusswiderstand: RW am Anfang und am Ende des Busses Analog-Ausgänge •4 Analog-Ausgänge •Ausgangssignal: •Auflösung: •max. Last: •DA-Wandler: U(nom) = 24 V DC (19 .. 30 V DC) I(nom) = approx. 100 mA approx. 2,5 W 2A reverse pole protection of the input voltage Micro processor and memory: •CPU: •Interfaces: ARM7 Architecture 1x CAN-Bus Communication: •CAN-Bus: •Transmission rate: •Bus line: •Terminating resistor: CAN 2.0B, galvanically isolated ISO 11898 10 kbit/s...250 kbit/s, default 50 kbit/s CAN-Bus line wave impedance RW = 120 Ohm RW at the beginning and at the end of the bus Analog outputs: 0 .. 10 V DC 100 mV 8 mA je Ausgang Delta-Sigma-Wandler DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ •4 analog outputs •Output signall: •Resolution: •max. load: •DA-converter: 0 .. 10 V DC 100 mV 8 mA per output Delta-Sigma-converter +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 4 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Anzeige- und Bedienelemente Display and control elements 1 Status LED S1 / Status LED S1 2 Anzeige und Bedienelemente / Display and control elements 3 Anschlusskontakte für Brückenbusstecker (CAN-Bus und Spannungsversorgung) contacts for bridge bus connectors (CAN-Bus and Power supply) 4 Adressschalter Low / Address switch Low 5 Adressschalter High / Address switch High 6 Status LED S2 / Status LED S2 Spannungsversorgung / Busanschluss Power supply / Bus connection Die Einspeisung der Versorgungsspannung und des CANBusses für die OPEN IO Module erfolgt in Verbindung mit dem Koppelmodul DS-PKM über einen Brückenbusstecker. The input of the supply voltage and the CAN bus for the OPEN IO modules take place in connection with the coupling module DSPKM via the bridge bus connector. © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Hinweis: Bis zu 15 aufeinanderfolgende Module dürfen über den Busstecker miteinander verbunden werden. Darüber hinaus muss eine weitere externe Einspeisung der Spannungsversorgung erfolgen. Note: Up to 15 successive modules can be connected together via a bus connector. In addition, another external supply voltage input have to take place. * Nicht belegte Klemmen dürfen nicht als Klemmstützpunkt belegt werden. * Unused terminals must not be used as connecting terminals. Klemmenbelegung Spannungsversorgung und CAN-Bus Terminal configuration Power supply and CAN-Bus CAN-Bus für OPEN IO Module CAN-bus for OPEN IO modules Anschlusskontakte für Brückenbusstecker contacts for bridge bus connectors CG H L 0V 3 + 24V PIN / Pin Signal / signal CG CAN-Ground H CAN-High L CAN-Low Spannungsversorgung für OPEN IO Module Power supply for OPEN IO modules Anschlusskontakte für Brückenbusstecker contacts for bridge bus connectors PIN / Pin Signal / signal 0 V Masse / GND +24 V +24 V DC DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 5 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Klemmenbelegung / Terminal configuration C-AO4 © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . C-AO4H 2a Anzeige LEDs und Bedienelemente Analog-Ausgänge AO0 ... AO3 2a Anzeige LEDs Analog-Ausgänge AO0 ... AO3 LED display analog outputs AO0 ... AO3 LED display and control elements analog outputs AO0 ... AO3 Hinweise: Nicht belegte Klemmen dürfen nicht als Klemmstützpunkt belegt werden. Note: Unused terminals may not be used as connecting terminal. Anzugsmoment bei Verwendung von Schraubklemmen - max. 0,4 Nm Tightening torque by using the screw terminals - max. 0,4 Nm DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 6 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Bedien-Funktionselemente Control- Functional elements CAN-Bus Adresse einstellen (High / Low) Configure the CAN-Bus address (High / Low) Über diese Adress-Schalter wird die Adresse des OPEN IO Moduls eingestellt. Über die Adresse wird ein OPEN IO Modul am CAN-Bus eindeutig identifiziert. Für die Adresssierung werden die Schalterstellungen jeweils „0“ bis „9“ verwendet. Dadurch sind Bus Adressen von „01“ bis „99“ einstellbar. Die Adresse „00“ und die jeweiligen Schalterstellungen „A“ bis „F“ werden nicht verwendet. The address of the OPEN IO modules will be adjusted via this address switch. By this address a OPEN IO module will be clearly identified at a CAN-Bus. For the addressing the switching positions are used in each case „0“ to „9“.Therefore Bus addresses are adjustable from „01“ to „99“. The address „00“ and the respective switching positions „A“ to „F“ are unused. Status LED S1 und S2 Status LED S1 and S2 Über die Status LEDs S1 und S2 wird der aktuelle Betriebszustand des OPEN IO Moduls angezeigt: The current operating state of the OPEN IO module is displayed via the status LEDs S1 and S2: S1 S2 © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . grün blinkend Bedeutung S1 Normaler Betriebszustand: Die Bus-Adresse ist auf einen gültigen Bereich eingestellt (01..99). In diesem Betriebszustand wird über die Status LED S2 der Bus-Zustand angezeigt. green flashing aus Das OPEN IO Modul wird von einer OPEN EMS angesprochen. rot blinkend Das Modul erkennt gültige CANTelegramme am Bus. Es wird aber nicht direkt von einer OPEN EMS angesprochen. Die eingestellten Adressen sollten überprüft werden. rot Es werden keine gültigen CANTelegramme am Bus erkannt. gelb Beim Versenden eines CAN-Telegramms ist ein Fehler aufgetreten. Es wurden keine weiteren CAN-Teilnehmer am Bus erkannt. gelb blinkend Eine ungültige Adresse ist eingestellt. grün/ gelb blinkend Das OPEN IO Modul befindet sich im Service-Betrieb. gelb gelb grün schnell blinkend Wenn beide LEDs gelb leuchten, wurde direkt zuvor ein Adressschalter verdreht. Nach einigen Sekunden übernimmt das Modul die neue Bus-Adresse. Interner Hardware Konfigurationsfehler. rot schnell blinkend Interner Hardware Konfigurationsfehler. DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ S2 Description Normal operating state: The Bus-address is set on a valid range (01..99). . In this operating state the Bus status is displayed via the status LED S2. off The OPEN IO module is connected to the OPEN EMS. red flashing The module recognizes valid CANtelegrams at the Bus. But the module is not directly addressed by a OPEN EMS. The set addresses should be checked. red No valid CAN-telegram is recognized on the Bus. yellow By sending a CAN-telegram an error occured. No further CAN-devices were recognized at the Bus. yellow flashing An invalid address is set. green/ yellow flashing The OPEN IO module is in the service-mode. yellow yellow green fast flashing If both LEDs shine yellow, an address switch was twisted directly before. After some seconds the module accepts the new Bus-address. Internal hardware configuration fault. red fast flashing Internal hardware configuration fault. +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 7 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Bedeutung der LED Anzeigen Function of the LED indicators Analog-Ausgänge OPEN IO Module AI8AO4 / AI8AO4H / AO4 / AO4H Analog-Outputs OPEN IO modules AI8AO4 / AI8AO4H / AO4 / AO4H LED Bedeutung LED Function Impulse (gelb) Die Anzahl der Impulse (Zustands-Blinken) gibt den Wert des Ausgangs an. Jeder Impuls entspricht ca. 10% (1 Volt) des Spannungsbereiches. Befindet sich ein Ausgang im Automatikbetrieb erfolgt vor jedem Zustands-Blinken eine kurze Pause, im Hand-Betrieb erfolgt vor jedem Zustands-Blinken eine Folge sehr kurzer Blink-Impulse. Pulses (yellow) The number of pulses (flashing status) indicates the value of the output. Each pulse corresponds to about 10% (1 volt) of the voltage range. If an output is in the automatic mode a brief pause takes place before each state-flashing. In the handmode a series of very short flash pulses take place before any state-flashing. © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Funktionsweise der Handbedienung bei OPEN IO Modulen mit Handtastern Functionality of the manual control concerning OPEN IO modules with buttons Bedienung der Hand-Ebene Operation of the manual control IO Modul AI8AO4H / AO4H Funktion IO module AI8AO4H / AO4H Function Handmodus aktivieren á (3 sek) Drücken Sie den Taster nach oben und halten ihn 3 Sekunden um den Handmodus zu aktivieren. activate manual mode á (3 sec.) Press the button upwards and hold it 3 seconds to activate the manual mode. Ausgangswert erhöhen á kurz tasten Drücken Sie den Taster kurz nach oben um den Ausgangswert um + 10% (+1 V) zu erhöhen. Press the button shortly upwards to increase the initial value to + 10% (+1 V). Ausgangswert verringern â kurz tasten Drücken Sie den Taster kurz nach unten um den Ausgangswert um - 10% (-1 V) zu verringen. Increase initial value á push up shortly Press the button shortly down to reduce the initial value to - 10% (-1 V). Handmodus deaktivieren â (3 sek) Drücken Sie den Taster nach unten und halten ihn 3 Sekunden um den Handmodus zu verlassen und zum Automatik-Betrieb zurückzukehren. Reduce initial value â push down shortly manual mode off â (3 sec) Press the button down and hold it three seconds to exit the manual mode and return to automatic mode. DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 8 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Anschlussschemen / Connection schemes Anschluss Versorgungsspannung Connection power supply +24V + - 0V 24V DC Analog-Ausgänge / Analog outputs Anschluss 0 ... 10 V (AO) bei angeschlossenen Geräten mit eigener Spannungsversorgung Connection 0 ... 10 V (AO) at connected devices with own power supply © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Anschluss 0 ... 10 V (AO) Connection 0 ... 10 V (AO) DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 9 OPEN IO Modul CAN-BUS C-AO4H / C-AO4 OPEN IO module CAN-BUS C-AO4H / C-AO4 Datenblatt - Stand: 18.05.2015 Data sheet - Issue date: 18.05.2015 Maßzeichnung Dimensions 45 T (D) mm 60 mm 27 ,5 mm 35 98 90 mm mm mm 27 ,5 H (H) mm 54 mm B (W) 54 mm x 60 mm x 90 (98) mm Dimensions (WxDxH): 54 mm x 60 mm x 90 (98) mm © DEOS control systems GmbH 2015. Technische Änderungen und Irrtümer vorbehalten / Errors and changes excepted . Abmessungen (BxTxH): Hinweise: •Maß für Handschalter nur bei IOModulen mit Handbedienebene •Maß für LED nur bei IO-Modulen mit LED Anzeigen Note: •Measure for manual switch only for IO modules with manual control •Measure for LED only for IO modules with LED displays DEOS control systems GmbH Birkenallee 76 ▪ 48432 Rheine ▪ Germany ▪ +49 5971 91133-20 ▪ +49 5971 91133-2995 ▪ [email protected] ▪ www.deos-ag.com 10