distitron
Transcrição
distitron
T Teecchhnniccaall daattaa shheeett DISTITRON VE 100 First emission Erste Ausgabe 01/05/1996 Resin type Harztype Bisphenol-A Epoxy Resin based vinyl ester Vinylester, basierend auf Bisphenol-A Epoxidharz Special features Besondere Eigenheiten Pure resin Reines Harz Processing Verfahren Cont. mould, fil. winding, pultrusion Handlaminieren, Wickeln, Pultrusion Note Anmerkung Certificate: RINA Zertifikat: RINA Type According to: VE 7A UP 5 1310 EN 13121-1 DIN 18820-1 DIN 16946-2 Delivery specification of the liquid resin Distitron VE100 Lieferspezifikations des flüssigen Harzes Distitron VE100 Properties Value Test method Unit Eigenschaften Einheit Testmethode Wert Viscosity RVF at 25°C, s 2 rpm 20 GM025 mPa.s 380 - 480 Viskosität RVF bei 25°C, s 2 rpm 20 Monomer content RS06C % 42 - 46 Monomergehalt Curing at 25°C with 0.5% Co6% + 1.5% Cumyl hydroperoxide Reaktivität bei 25°C mit Gel time RS08G min.sec 11.00 - 15.00 Gelzeit Curing time RS08G min.sec 19.00 - 28.00 Härtungszeit Maximum temperature °C RS08G 165 - 195 Maximale Temperatur Properties of the liquid resin Distitron VE100 Eigenschaften des flüssigen Harzes Distitron VE100 Appearance - colour Yellow RS13F -----------Aussehen - Farbzahl Gelb Acid number RS02C mg KOH/g 8 Max Säurezahl Stability at 20°C in the dark months RS07G 6 Stabilität bei 20°C im Dunkeln Monate Technical Data Sheet DISTITRONVE 100 Version: n. 20, 06/14/2013 Pag. 01 of 02 Properties of cured unreinforced resin Distitron VE100 Eigenschaften des gehärteten nicht verstärkten Harzes Distitron VE100 Casting preparation: Gießvorbereitung: 50 ppm Ac Acetone Hardner type and amount: Härtertyp u. Menge: 1.5% Cumyl hydroperoxide Promotor type and amount: Beschleunigertyp u. Menge: 0.3% Co6% Curing cycle: Härtungszyklus: 24h at 23°C + 2h at 100°C + 1h at 100°C 24h bei 23°C + 2h bei 100°C + 1h bei 100°C Properties Eigenschaften Tensile strength Zugfestigkeit Tensile modulus Zugmodul Stress at yield Zugfestigkeit Strain at yield Streckdehnung Nominal strain at break Nominale Dehnung bei Bruch Flexural strength Biegefestigkeit Flexural modulus Biegemodul Heat deflection temperature Wärmeverformungstemperatur Glass transition Glasübergangstemperature Overall volume shrinkage Volumenschrumpfung Barcol hardness at 25°C Barcol Härte bei 25°C Test method Testmethode Unit Einheit Typical value Typischer Wert ISO 527-2012 MPa 85 ISO 527-2012 MPa 3200 ISO 527-2012 MPa 85 ISO 527-2012 % 5.0 ISO 527-2012 % 6.6 ISO 178-2010 Method B ISO 178-2010 Method B ISO 75 - 2:2004 Method A MPa 145 MPa 3300 °C 106 °C 114 % 7.3 Unit Einheilt 37 (*) ASTM E 1545-11 (*) ISO 3521-1997 corr. 1:2003 ASTM D 2583-07 (*) by Thermo Mechanical Analisys The information contained in this brochure is correct and accurate and is based on our technical and scientific knowledge at the date of going to press. Such information relates only to use of the products in the pure state and for the purpouses stated herein. Nothing stated here may be taken or construed as implying a breach of any existing patents. Nor is any warranty, whether expressed or implicit, given with regard to the results to be obtained through the use of the aforesaid information. Die in dieser Broschüre enthaltene Information ist korrekt und genau und basiert auf unserer technischen und wissenschaftlichen Kenntnis zum Zeitpunkt des Drucks. Solche Information bazieth sich nur auf den Gebrauch des Produkts in reinen Zustad und für die hierin angegebenen Zwecke. Nichts von dem hier angegebenen darf genommem oder ausgelegt werden als Bainhaltung einen Bruchs jeglicher bestehender Patente. Noch wird jegliche Garantie, ob ausdrücklich oder impliziert, in Hinsicht auf die durch Verwending der zuvor gesagten. Information zu erhaltenden Ergebnisse gegeben. Technical Data Sheet DISTITRONVE 100 Version: n. 20, 06/14/2013 Pag. 02 of 02