proAMT Flyer
Transcrição
proAMT Flyer
2012 Mundorf introduces an all-new line of highly stressable but extremely distortionless ProAMT®tweeter devices. ProAMT®Essentials Air Motion Transformer (AMT®) are line-sources as a matter of principle, thus they are very easy to integrate in any Line Array design without requiring wave-guides and phase-plugs. Regular horn designs are sufficient. Combining various patented and patent pending innovations, these all-new ProAMT®drivers not only match the sensitivity of HQ compression drivers but yet exceed their power handling ability - at a distortion ratio as low as never achieved before with any other tweeter device around. Both their short time peak capability (1000W) and their long time power handling up to 150W (sinus continuous) are remarkable specs, whereas the thermally caused power compression remains very low. Available standard sizes are 2,5“ - 5“ - 6“ - 8“ 10“ - 12“ and, there are 3 design concepts to distinguish. Firstly, planar devices applicable from <1kHz, secondly, ultra flat devices developed for usage from <2kHz up to >18kHz and, thirdly, very compact devices with specially U-shaped pole plates, also usable from 1kHz. Also, compact ProAMT®drivers with a wide vertical dispersion angle are available. In fact, both driver ranges match both the requested dispersion angle and the hight of the line-source, respectively, its requested vertical dispersion angle. A power input dependent and, continuously running ventilation system is available for all models. That way, even extreme power loads can be achieved safely and, at reasonable low costs. Turnkey horn funnels are under construction, data sheets on optimized horn geometries are availble upon request. www.mundorf.com ProAMT® 336PP-12“ Ultra Flat Driver Der ProAMT® 336PP27F-618-109-F wurde als Hochtöner für 3-WegeApplikationen entwickelt. Die hohe obere Grenzfrequenz und die außergewöhnlich niedrigen Verzerrungswerte vereinen Pro-Anforderungen und Hifi-Qualität. 105 100 95 Der dargestellte Treiber steht als Beispiel dieser ultraflachen Bauform, die in verschiedenen Höhen, Impedanzen und mit unterschiedlichen Abstrahlwinkeln zur Verfügung steht, und sowohl mit als auch ohne Zwangskühlung angeboten wird. ProAMT® 336PP-12“ 336PP27F-618-109-F/SPL& Phase 2k 10k 20k ProAMT® 336PP27F-618-109-F was developed as tweeter for 3-way-application. Its high upper frequency limit and its excellent lower distortion value combine pro-audio requirements and hi-fi quality. The presented driver is an example of this ultra flat design, which is available in various heights, impedances and with different radiation angles, and is provided both with and without forced-air cooling. 5,0 5,0 336PP27F-618-109-F/Impedance 2k 10k 20k 114 1,0 0,1 336PP27F-618-109-F Specs 336PP27F Sensitivity 2.83V/m: 105dB SPLmax: >133dB Peak Power Handling: 1000 W Continuous Sinus PH: 150 W FQ Response: 2.5kHz – 18kHz Impedance: 6, 12 and 18 Ohm 2k 10k www.mundorf.com/amtnews ProAMT®197 PP-8“ 105 100 95 4.2 3.8 ProAMT® 197PP-8“ 197PP27R-740-121-F/SPL/SPL Horn Loaded/Impedance 2k 10k 20k 114 1,0 0,1 0,1 197PP27R-740-121-F Horn Loaded 2k 10k 197PP27R-740-121-F 20k Der ProAMT®197 PP 27R740-121-F wurde als ein gemeinsames Projekt mit der FH Düsseldorf, Fachbereich Akustik entwickelt. Patentierte Membran-Technologie und eine ebenfalls zum Patent angemeldete signalgesteuerte Zwangskühlung ermöglichen problemlos Belastbarkeiten, die bisher modernen Kompressionstreibern vorbehalten waren bzw. diese teilweise noch übertreffen! Die Verzerrungen bewegen sich hierbei allerdings auf einem unschlagbar niedrigen Niveau, zumal die THD fast ausschließlich aus eher unkritischen K2 bestehen: Die eigentlich störenden K3, K5 und K7 sind nahezu nicht vorhanden. Der dargestellte Treiber steht als Beispiel dieser Bauform, die in verschiedenen Höhen, Impedanzen und mit unterschiedlichen Abstrahlwinkeln zur Verfügung steht, und sowohl mit als auch ohne Zwangskühlung angeboten wird. ProAMT®197 PP 27R–740-121-F was developed as a collective project with the FH Düsseldorf (University of Applied Sciences). Its patented membrane technology and similarly patent pending signal-controlled forced-air cooling enable load capacities, which until now were reserved for modern compression drivers and, even partly surpass these respectively! Its distortion ratio, however, remains at an unchallenged low level, especially as the THD consist almost merely of rather uncritical K2: the rather disturbing K3, K5 and K7 are virtually non-existent. The presented driver is an example of this special design, which is available in various heights, impedances and with different radiation angles, and is provided both with and without forced-air cooling. 1k 10k Specs 197PP27R Sensitivity 2.83V/m: 104dB SPLmax: >132dB Peakpower Handling: 1000 W Continious Sinus PH: 150 W FQ: 900Hz – 16kHz Impedance: 6, 12 and 18 Ohm ProAMT®168PP-6“ 105 Der ProAMT®168PP27R-628-141 wurde als Beispiel für die Einstiegsklasse der ProAMT® ausgewählt. Aufgrund seines linearen Frequenzganges kann er auch ohne Horn betrieben werden. Sein Maximalpegel von 125 dB und die sehr geringen Verzerrungswerte bilden eine hervorragende Basis für klanglich anspruchsvolle und preisbewusste Projekte. 100 95 4,8 ProAMT® 168PP-6“ Der ProAMT®168PP27R-728-197 ist ein weiteres Beispiel für die Einstiegsklasse. Sein Frequenzgang ist zu den tiefen Frequenzen hin erweitert; er sollte allerdings vorzugsweise mit einem kurzen Horn betrieben werden. 168PP27R-628-141 2k 10k 20k 105 Der dargestellte Treiber steht als Beispiel dieser Bauform, die in verschiedenen Höhen, Impedanzen und mit unterschiedlichen Abstrahlwinkeln zur Verfügung steht, und sowohl mit als auch ohne Zwangskühlung angeboten wird. 100 95 ProAMT®168PP27R-628-141 was chosen as an example for the ProAMT® entry level category. Due to its linear frequency response, it can also be operated without the horn attachment. Its maximum level of 125 dB and its very low distortion ratio provide an excellent basis for demanding but cost-conscious sound projects. 4,9 168 PP-27-R-728-197 2k 10k 20k The ProAMT®168PP27R-728-197 is another example for this entry level category. Its frequency response is extended to the low frequencies, but should be operated primarily with a short horn. The presented drivers are an example of this compact design, which is available in various heights, impedances and with different radiation angles, and is provided both with and without forced-air cooling. Specs 168PP27R-628-141 Sensitivity 2.83V/m: 100dB SPLmax: 125dB Peak Power Handling: 300W Continuous Sinus PH: 40W FQ Response: 1350Hz – 18kHz Impedance: 4.5 and 8 Ohm vs Data 168PP27R-728-197 FQ Response: 800Hz – 16kHz Impedance: 3.5, 6.8, 10 Ohm 114 1,0 0,1 168PP27R-628-141 2k 10k www.mundorf.com/amtnews ProAMT®168PU-6“ 105 100 95 ProAMT® 168PU-6“ 168PU27R-4680-95/Impedance/Phase 5,8 2k 10k 20k 105 100 95 168PU27R-4680-95 SPL Horn Loaded Der ProAMT®168PU27R-4680-95 wurde als kompakter und besonders schmaler Treiber entwickelt. Dies wird durch die patentierte U-förmige Ausführung der Polplatten erreicht. Damit wird der problemlose Einbau zwischen zwei Tief-Mitteltönern ermöglicht. Das untere SPL Diagramm zeigt den Frequenzgang bei Verwendung eines entsprechenden Hornvorsatzes. Der dargestellte Treiber steht als Beispiel der U-Bauform, die in verschiedenen Höhen, Impedanzen und mit unterschiedlichen Abstrahlwinkeln zur Verfügung steht, und sowohl mit als auch ohne Zwangskühlung angeboten wird. The ProAMT®168PU27R-4680-95 was developed as a compact and ultra slim driver. This is achieved through the patented U-shaped design of its pole plates. Thus, its assembly between two mid-woofers is no problem. The lower SPL diagram shows the frequency response when using a corresponding horn attachment. The presented driver is an example of this special U-design, which is available in various heights, impedances and with different radiation angles, and is provided both with and without forced-air cooling. 2k 10k 20k 114 1,0 0,1 168PU27R-4680-95 Distortion 114dB 2k 10k Specs 168PU27R Sensitivity 2.83V/m: 104dB SPLmax: >131dB Peak Power Handling: 600W without/1000W with fan Continuous Sinus PH: 60W without/120W with fan FQ Response: 900Hz – 16kHz Impedance: 3.3, 3.9, 6, 10 Ohm ProAMT®164UM-6“ Der ProAMT®164UM ist ein gezielt entwickelter Monitor-Hochtöner. Hohe Empfindlichkeit, weiter Frequenzbereich und hohe Belastbarkeit vereint er mit hohem Schalldruck in äußerst kompakten Maßen. Damit sind seine Einsatzmöglichkeiten in modernen Abhörlautsprechern nahezu unbegrenzt. Zweifellos setzt dieser Treiber mit seiner ProAudioPerfomance in HighEnd Audio Qualität neue Maßstäbe. 100 95 7,8 ProAMT® 164UM-6“ Der dargestellte Treiber steht als Beispiel dieser kompakten Bauform, die in verschiedenen Höhen, Impedanzen und mit unterschiedlichen Abstrahlwinkeln zur Verfügung steht, und sowohl mit als auch ohne Zwangskühlung angeboten wird. ProAMT®164UM is a specifically developed tweeter for monitor speakers. It combines high sensitivity, wide frequency response and high power handling with equally high SPL. All together in a rather small enclosure. Thus, its application in modern monitors is virtually unlimited. Unquestionably, by its pro-audio performance in high end audio quality this driver sets a new benchmark. The presented driver is an example for compact design, which is available in various heights, impedances and with different radiation angles, and is provided both with and without forced-air cooling. Specs 164UM1.1 Sensitivity 2,83V 1/m: 96dB SPLmax: >125dB Peak Power Handling: 300 W Continious Sinus PH: 30 W FQ Response: 2.5kHz-30kHz Impedance: 8 Ohm Specs 164UM2.1 Sensitivity 2,83V 1/m: 97dB SPLmax: >126dB Peak Power Handling: 300 W Continious Sinus PH: 30 W FQ Response: 1.5kHz-28kHz Impedance: 8 Ohm 164UM1.1 green - 164UM2.1 blue 2k 10k 20k 114 1,0 0,1 164UM1.1 Distortion 114dB 2k 10k 20k 164UM2.1 Waterfall 2k 10k www.mundorf.com/amtnews AMT®2510c HiFi AMT ® 95 7,0 AMT® 2510c AMT 2510c SPL/Impedance/2.83V 2k 10k 20k Der AMT® 2510c ist das Topmodell der Mundorf HiFi Air Motion Transformer, und sicherlich nicht nur messtechnisch einer der absolut besten Hochtöner, die heute für hochwertige HiFi Systeme angeboten werden. Ob in 2- oder 3-Wege-Lautsprechern, ob ganz leise oder richtig laut, seine lebendige Musikwiedergabe ist immer auffallend schön und klar. The AMT® 2510c is Mundorf‘s top model of the HiFi Air Motion Transformer line and certainly not only by its specs one of today‘s absolutly best tweeters available for high performance audio systems. Regardless whether in 2- or 3-way-applications, whether at utmost low volume or really loud, its music performance is always remarkably lovely and clear. 104 AMT 2510c Distortion 104dB 2k 10k 20k AMT 2510c Waterfall 2k 10k Specs AMT®2510c Sensitivity 2,83V 1/m: 94dB SPLmax: >123dB Peak Power Handling: 250 W Continious Sinus PH: 25 W FQ Response: 1.6kHz-23kHz Impedance: 7.8 Ohm AMT®1908c/2109c HiFi AMT ® 95 90 AMT® 1908c/2109c SPL@2,83V red: AMT 2109c/blue: AMT 1908c 2k AMT 1908c Distortion 95dB 2k 10k 20k Der AMT® 1908c/2109c ist ein Mundorf HiFi Air Motion Transformer für hochwertige 3-Wege-Lautsprecher. Der lineare Frequenzgang, die AMT® typische Verzerrungsarmut und die hohe Empfindlichkeit bestimmen seine ausgewogene Musikwiedergabe, über die man hier viele wohlklingende Worte schreiben könnte. Und doch würde der 1908c/2109c ‚life‘ immer noch viel besser klingen. The AMT® 1908c/2109c is a Mundorf HiFi Air Motion Transformer for high quality 3-way systems. Linear frequency response, AMT® typical low distortions and the high sensitivity define its well-balanced music performance, on which one could write many pleasant-sounding words. And yet, ‘in the real world‘ the 1908c/2109 would still sound much better. 10k AMT 2109c Waterfall Specs AMT®1908c Sensitivity 2,83V /1m: 90dB SPLmax: >113dB Peak Power Handling: 160 W Continious Sinus PH: 15 W FQ Response: 2.6kHz-31kHz Impedance: 8.3 Ohm 2k 10k [email protected] Specs AMT®2109c Sensitivity 2,83V /1m: 92dB SPLmax: >115dB Peak Power Handling: 160 W Continious Sinus PH: 15 W FQ Response: 2.1kHz-28kHz Impedance: 4.6 Ohm MUNDORF EB GmbH Liebigstrasse 110 50823 Cologne Germany phone: +49 221 9777050 fax: +49 221 97770599