Galea™ Life / Sistena Life Flood detector 7756 77
Transcrição
Galea™ Life / Sistena Life Flood detector 7756 77
Galea™ Life / Sistena Life Flood detector 7756 77 Technical data 100 - 240 V~ 50/60 HZ Ι 230 V~ ST N TE LEAR 1 X 2,5 mm² / 2 X 1,5 mm² 0°C ... + 40°C 10 mA 20 mA 2 A 250 V~ / Pmax. 60 VA IP 30 85 dB (A) à 1 m IK 04 Max length of the sensor < 1 m Media In One by Legrand PLC LE00517AA U Description Buzzer Indicator light detection /fault (red/yellow) Indicator light LEARN (green) LEARN TEST Indicator light power on (green) LEARN key & CONTROL key on the second press TEST button Sensor 2 Installation Connection 1m max. 0 - 5 mm solenoid valve 3 Safety instructions This product should be installed in line with installation rules, preferably by a qualified electrician. Incorrect installation and use can lead to risk of electric shock or fire. Before carrying out the installation, read the instructions and take account of the product’s specific mounting location. Do not open up, dismantle, alter or modify the device except where specifically required to do so by the instructions. All Legrand products must be opened and repaired exclusively by personnel trained and approved by Legrand. Any unauthorised opening or repair completely cancels all liabilities and the rights to replacement and guarantees. Use only Legrand brand accessories. 4 Operation Switch on The green «power on» indicator light lights up. The «detection» indicator light flashes yellow/red for a few seconds and then goes out. Detection of a liquid conductor or short-circuit in the sensor The «detection» indicator light lights up and remains red, The intégral buzzer sounds intermittently, The state of the internal relay changes, An In One scenario control is emitted by powerline carrier (PLC) to the associated In One product(s) during learning TEST mode Pressing the TEST button simulates a flood detection until it is released (the TEST button is accessible only when the cover is removed). - Flood detector Cat. No. 7756 77 is compatible with the scenario controller Cat. No. 7756 19. - It can be linked to In One radio products via the PLC/RF modular interface. Definitions Learning : procedure which enables a scenario to be defined and recorded. Scenario: a set of controls carried out simultaneously on the various receivers which have been linked to the receiver during the learning procedure 5 Installation 2-gang flush-mounting box Finish Mechanism Cover plate White 7810 43 7719 00 Dark bronze 7812 43 7719 10 Soft Aluminium 7813 43 7719 20 Titanium 7814 43 7719 30 Pearl 7815 43 7719 40 ST N TE LEAR Plate 2 x 1 6 Accessory Cat. Nos Cover Legend LEARN key : CONTROL key : LEARN Indicator light The indicator light goes off The indicator light blinks slowly The indicator light blinks quickly The indicator light flashes Learning scenario Transmitter LEARN indicator light 1 Open the scenario 2 7 Receiver(s) LEARN indicator light Learning scenario (continued) Transmitter LEARN indicator light Receiver(s) LEARN indicator light 3 4 To add several products to the scenario, repeat operations 3 and 4 for each receiver. 5 Save the scenario The learning phase is completed. The solenoid valve will be operated and the water circuit will be closed immediately when a leak is detected. 8 Modifying a scenario Transmitter LEARN indicator light Receiver(s) 1 Open the scenario 2 3 4 or to delete the product from the scenario, skip to 6 9 LEARN indicator light Modifying a scenario (continued) Transmitter LEARN indicator light Receiver(s) LEARN indicator light 5 6 Save the scenario Deleting a scenario Delete all the scenarios linked to this product (on the transmitter) 1 2 5s 10 s 10 Troubleshooting Problem Cause Solution The Learn indicator light comes on for 5 seconds. Learning is impossible. Install compatible products. The Learn indicator light comes on for 10 seconds. The number is memorised transmitters is greater than 32 Delete the unused scenarios. The Learn indicator light no longer blinks during learning The learning mode closes after 10 minutes. (with no action) Restart the learning. The programmed function button does not work. After pressing the Learn button once, function key learning must be done within the following minute Restart the learning. When the scenario is saved, the Learn indicator lights of certain receivers do not go out Poor communication between products Check the cabling (connection). Look for a possible interference device(*). Insulate with a filter. * Example of element causing interference: electronic transformer, switch mode power supply, ... ( ) 11 Declaration of conformity DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY Nous déclarons que les produits satisfont aux dispositions de : We declare that the products satisfy the prov isions of : La Directive 1999/5/CE du Parlement européen et du Conseil du 9 mars 1999 "R&TTE" Directive 1999/5/EC of the European Parliament and of the Council of 9 march 1999 "R&TTE" sous réserve d'une utilisation conforme à sa destination et/ou d'une installation conforme aux normes en vigueur et/ou aux recommandations du constructeur on condition that they are used in the manner intended and/or in accordance with the current installation standards and/or with the manufacturer's recommandantions 12 Galea™ Life / Sistena Life Wassermelder 7756 77 Technische Daten U 100 - 240 V~ 50/60 HZ Ι 230 V~ 0°C ... + 40°C 10 mA 20 mA 2 A 250 V~ / Pmax. 60 VA IP 30 85 dB (A) in 1 m IK 04 Max. Länge des Fühlers < 1 m Media In One by Legrand PLC LE00517AA ST N TE LEAR 1 X 2,5 mm² / 2 X 1,5 mm² 13 Beschreibung Warnsumme Leuchtdiode Erkennung / Fehler (rot / gelb) LEARN Leuchtdiode LEARN (grün) Leuchtdiode Spannungsanzeige (grün) TEST TEST-Taste LEARN-Taste & BEDIENTASTE beim zweiten Drücken Fühler 14 Installation Anschluss 1m max. 0 - 5 mm Gasmagnetventil 15 Sicherheitshinweise Dieses Produkt darf nur durch eine Elektro-Fachkraft eingebaut werden. Bei falschem Einbau bzw. Umgang besteht das Risiko eines elektrischen Schlages oder Brandes. Vor der Installation die Anleitung lesen, den produktspezifischen Montageort beachten. Das Gerät vorbehaltlich besonderer, in der Betriebsanleitung angegebener Hinweise nicht öffnen, zerlegen, beschädigen oder abändern. Alle Produkte von Legrand dürfen ausschließlich von durch Legrand geschultes und anerkanntes Personal geöffnet und repariert werden. Durch unbefugte Öffnung oder Reparatur erlöschen alle Haftungs-, Ersatz- und Gewährleistungsansprüche. Ausschliesslich Zubehör der Marke Legrand benutzen. 16 Funktionsweise Inbetriebnahme Erkennung einer leitenden Flüssigkeit oder eines Fühlerkurzschlusses TEST-Modus Die Leuchtdiode «Spannungsanzeige» leuchtet grün auf. Die Leuchtdiode «Erkennung» blinkt einige Sekunden lang gelb / rot auf und erlischt anschließend. Die Leuchtdiode «Erkennung» leuchtet rot auf. Der eingebaute Warnsummer gibt einen Intervallton ab. Das interne Relais ändert den Status. An das/die beim Einlernen verknüpfte(n) In One Gerät(e) wird per Trägerstrom (PLC) ein In One Szenariobefehl abgegeben. Beim Drücken der TEST-Taste wird bis zum Loslassen der Taste eine Über lauferkennung simuliert (die TEST-Taste ist nur mit abgenommener Abdec khaube erreichbar). - Der Wassermelder Art.-Nr. 7756 77 ist mit dem Szenariomanager kompatibel Art.-Nr. 7756 19 - Er kann über die PLC / Funk-Modulschnittstelle mit funkgesteuerten In One Geräten verknüpft werden. Begriffsbestimmungen Einlernen: Ablauf zur Festlegung und Speicherung eines Szenarios. Szenario: Alle Befehle, die gleichzeitig an den verschiedenen beim Einlernen mit dem Sender verknüpften Empfängern ausgeführt werden. 17 Montage Unterputz-dose 2-fach Finish Einsatz Abdeckhaube Abdeckplatte ultraweiß 7810 43 7719 00 Dark bronze 7812 43 7719 10 Soft Aluminium 7813 43 7719 20 Titanium 7814 43 7719 30 Perlmutt 7815 43 7719 40 ST N TE LEAR Abdeckplatte 2 x 1 18 Art.-Nr. Zubehör Abdeckhaube Zeichenerklärung LEARN-Taste : BEDIENTASTE : LEARN Leuchtdiode Die Leuchtdiode erlischt Die Leuchtdiode blinkt langsam Die Leuchtdiode blinkt schnell Die Leuchtdiode leuchtet auf Einlernen des Szenarios Sender LEARN Leuchtdiode 1 Das Szenario öffnen 2 19 Empfänger LEARN Leuchtdiode Einlernen des Szenarios (Fortsetzung) Sender LEARN Leuchtdiode Empfänger LEARN Leuchtdiode 3 4 Um weitere Geräte zu dem Szenario hinzuzufügen, wiederholen Sie bitte für jeden Empfänger die Bedienabläufe 3 und 4 . 5 Das Szenario speichern Der Einlernvorgang ist beendet - das Magnetventil wird angesteuert und der Wasserkreislauf unterbrochen, sobald ein Wasserleck erfasst wird. 20 Ändern eines Szenarios Sender LEARN Leuchtdiode Empfänger 1 Das Szenario öffnen 2 3 4 oder Zum Löschen des Gerätes aus dem Szenario zu 6 übergehen. 21 LEARN Leuchtdiode Ändern eines Szenarios (Fortsetzung) Sender LEARN Leuchtdiode Empfänger LEARN Leuchtdiode 5 6 Das Szenario speichern Löschen eines Szenarios Alle mit diesem Gerät verknüpften Szenarien löschen (am Sender) 1 2 5s 10 s 22 Fehler und Fehlerbehebung Fehler Ursache Fehlerbehebung Die Learn-Leuchtdiode leuchtet für 5 Sekunden auf. Einlernen ist unmöglich. Den Einlernvorgang mit kompatiblen Geräten durchführen. Die Learn-Leuchtdiode leuchtet für 10 Sekunden auf. Die Anzahl gespeicherter Sender liegt bei mehr als 32. Nicht gebrauchte Szenarien löschen. Beim Einlernen blinkt die LearnLeuchtdiode nicht mehr Der Einlernmodus wird 10 Minuten nach dem letzten Eingriff automatisch beendet. Den Einlernvorgang erneut beginnen. Die programmierte Funktionstaste funktioniert nicht. Nach einmaligem Drücken auf die Learn-Taste kann die Funktionstaste innerhalb einer Minute eingelernt werden. Den Einlernvorgang erneut beginnen. Beim Speichern des Szenarios erlöschen die Learn- Leuchtdioden mancher Empfänger nicht. Mangelhafte Kommunikation zwischen Geräten. Verkabelung (Anschluss) prüfen. Nach einem etwaigen Störgerät(*) suchen. Dieses dann gegebenenfalls mit einem Filter isolieren. * Mögliche Störquellen : Elektrischer Trafo, Stromspeisung, usw. ( ) 23 Konformitätserklärung DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY Nous déclarons que les produits satisfont aux dispositions de : We declare that the products satisfy the prov isions of : La Directive 1999/5/CE du Parlement européen et du Conseil du 9 mars 1999 "R&TTE" Directive 1999/5/EC of the European Parliament and of the Council of 9 march 1999 "R&TTE" sous réserve d'une utilisation conforme à sa destination et/ou d'une installation conforme aux normes en vigueur et/ou aux recommandations du constructeur on condition that they are used in the manner intended and/or in accordance with the current installation standards and/or with the manufacturer's recommandantions 24 Galea™ Life / Sistena Life Detector de inundación 7756 77 Caractérística téchnica U 100 - 240 V~ 50/60 HZ Ι 230 V~ 0°C ... + 40°C 10 mA 20 mA 2 A 250 V~ / Pmáx. 60 VA IP 30 85 dB (A) a 1 m IK 04 Longitud máx. de la sonda < 1 m Media In One by Legrand CPL LE00517AA ST N TE LEAR 1 X 2,5 mm² / 2 X 1,5 mm² 25 Descripción Timbre LEARN Indicador lumisimo detección / fallo (rojo / amarillo) Indicador lumisimo LEARN (verde) Indicador lumisimo presencia tensión (verde) TEST Botón TEST Botón LEARN & Botón de ACCIONAMIENTO al pulsar por segunda vez Sonda 26 Instalación Empalme 1m max. 0 - 5 mm electroválvula 27 Consignas de seguridad Este producto debe instalarse conforme a las normas de instalación y preferiblemente por un electricista cualificado. Una instalación y una utilización incorrectas pueden entrañar riesgos de choque eléctrico o de incendio. Antes de efectuar la instalación, leer las instrucciones, tener en cuenta el lugar de montaje específico del producto. No abrir, desmontar, alterar o modificar el aparato salvo que esto se indique específicamente en las instrucciones. Todos los productos Legrand deben ser abiertos y reparados exclusivamente por personal formado y habilitado por Legrand. Cualquier apertura o reparación no autorizada anula la totalidad de las responsabilidades, derechos a sustitución y garantías. Utilizar exclusivamente los accesorios de la marca Legrand. 28 Funcionamiento Puesta en tensión El indicador luminoso «presencia de tensión» se ilumina en verde El indicador luminoso «detección» parpadea en amarillo/rojo durante unos segundos, después se apaga. Detección de un líquido conductor o cortocircuito de la sonda El indicador luminoso «detección» se ilumina en rojo fijo, El timbre integrado emite un sonido intermitente, El relé interno cambia de estado, Un accionamiento de escenario In One se emite mediante corriente portadora (CPL) hacia el/los producto/s In One asociado/s durante el aprendizaje. Modo TEST Si se pulsa el botón TEST se simula una detección de inundación hasta que se suelta el botón. (el botón TEST est accesible únicamente cuando se desmonta el embellecedor) - El detector de inundación ref. 7756 77 es compatible con el gestor de escenarios ref. 7756 19. - Puede asociarse a productos In One radio por medio de la interfaz modular CPL / RF. Definiciones Aprendizaje: procedimiento que permite definir y grabar un escenario. Escenario: conjunto de accionamientos ejecutados simultáneamente en los diferentes receptores asociados al emisor durante el aprendizaje. 29 Montaje Caja de empotrar doble acabado Mecanismo Embellecedor placa Blanco 7810 43 7719 00 Bronze Oscuro 7812 43 7719 10 Aluminio Claro 7813 43 7719 20 Titanio 7814 43 7719 30 Blanco Perla 7815 43 7719 40 ST N TE LEAR Placa 2 x 1 30 Referencias accesorios Embellecedor Leyenda Botón LEARN: Botón de ACCIONAMIENTO : LEARN Indicator lumisimo El indicador luminoso se apaga El indicador luminoso parpadea despacio El indicador luminoso parpadea rápido El indicador luminoso parpadea Aprendizaje del escenario Emisor Piloto LEARN Receptor(es) Piloto 1 Abrir el escenario 2 31 Piloto LEARN Aprendizaje del escenario (continuación) Emisor Piloto LEARN Receptor(es) Piloto Piloto LEARN 3 4 Para añadir varios productos al escenario, repetir para cada receptor las operaciones 3 y 4. 5 Grabar el escenario El aprendizaje se ha terminado: la electroválvula se accionará y el circuito de agua se cerrará en cuanto se detecte una fuga de agua. 32 Modificación de un escenario Emisor Piloto LEARN Receptor(es) Piloto 1 Abrir el escenario 2 3 4 o Para suprimir el producto del escenario, pasar a 6. 33 Piloto LEARN Modificación de un escenario (continuación) Emisor Piloto LEARN Receptor(es) Piloto 5 6 Grabar el escenario Borrado de un escenario Borrar todos los escenarios relacionados con este producto (en el emisor) 1 2 5s 10 s 34 Piloto LEARN Problemas y soluciones Problema Causa Solución El indicador luminoso Learn se enciende durante 5 segundos. El aprendizaje es imposible. Instalar productos compatibles. El indicador luminoso Learn se enciende durante 10 segundos. El número de emisores memorizados es superior a 32. Suprimir los escenarios inutilizados. Durante el aprendizaje el indicador luminoso Learn ya no parpadea. El modo aprendizaje se cierra al cabo de 10 minutos (sin acción). Reiniciar el aprendizaje. La tecla Función programada no funciona. Tras pulsar una vez la tecla Learn, el aprendizaje de la tecla Función se hace en el minuto siguiente. Reiniciar el aprendizaje. Al registrar el escenario, los indicadores luminosos Learn de ciertos receptores no se apagan. Mala comunicación entre los productos. Verificar el cableado (conexión). Buscar si existe un dispositivo perturbador (*). Aislarlo con un filtro. * Ejemplo de un dispositivo perturbador: transformadores electrónicos, alimentación de corte, etc. ( ) 35 Declaración de conformidad DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY Nous déclarons que les produits satisfont aux dispositions de : We declare that the products satisfy the prov isions of : La Directive 1999/5/CE du Parlement européen et du Conseil du 9 mars 1999 "R&TTE" Directive 1999/5/EC of the European Parliament and of the Council of 9 march 1999 "R&TTE" sous réserve d'une utilisation conforme à sa destination et/ou d'une installation conforme aux normes en vigueur et/ou aux recommandations du constructeur on condition that they are used in the manner intended and/or in accordance with the current installation standards and/or with the manufacturer's recommandantions 36 Galea™ Life / Sistena Life Detector de gás inundação 7756 77 características téchnicas U Ι 230 V~ 1 X 2,5 mm² / 2 X 1,5 mm² 0°C ... + 40°C 10 mA 20 mA 2 A 250 V~ / Pmáx. 60 VA IP 30 85 dB (A) a 1 m IK 04 Comprimento máx. da sonda < 1 m Media In One by Legrand PLC LE00517AA ST N TE LEAR 100 - 240 V~ 50/60 HZ 37 Descrição Sinalizador acústico Sinalizador de detecção /defeito (vermelho/amarelo) Sinalizador de LEARN (verde) LEARN TEST Sinalizador de presença de tensão (verde) Botão TEST Botão LEARN & Tecla COMANDO premindo 2vezes Sonda 38 Instalação Esquema de ligações 1m máx. 0 - 5 mm Electroválvula 39 Instruções de segurança Este produto deve ser instalado de acordo com as regras de instalação e de preferência por um electricista qualificado. A instalação e o uso incorrectos podem provocar riscos de choque eléctrico ou de incêndio. Antes de efectuar a instalação, ler as instruções e ter em conta a localização adequada para a montagem do produto. Não abrir, desmontar, alterar ou modificar o aparelho salvo especificação em contrário nas instruções do produto. Todos os produtos Legrand só devem ser abertos e reparados exclusivamente por pessoal formado e autorizado pela Legrand. Qualquer abertura ou reparação não autorizada cancela todas as responsabilidades, direitos de substituição e garantias. Utilizar exclusivamente os acessórios da marca Legrand. 40 Funcionamento Ligação à rede eléctrica O sinalizador de «presença de tensão» acende-se (verde). O sinalizador de «detecção» pisca (amarelo / vermelho) durante vários minutos, apagando-se em seguida. Detecção de um líquido conductor conductor O sinalizador de «detecção» acende-se (vermelho), O sinalizador acústico emite um sinal intermitente, O contacto de saída muda de posição, É enviado um comando de cenário por portadora de corrente (PLC), aos produtos In One associados após o procedimento de memorização. Modo TEST Mantendo premido o botão TEST simula-se uma detecção de inundação (o botão TEST só se encontra acessível após remoção do espelho do produto). - O detector de inundação ref. 7756 77 é compatível com o Controlo de Cenários ref. 7756 19. - Pode comunicar com produtos In One que operam por radiofrequência (RF), através da interface PLC / RF. Definições Memorização: acção que permite definir e memorizar um cenário. Cenário: conjunto de comandos executados simultaneamente por diversos produtos receptores que foram associados a um comando emissor central durante o procedimento de memorização. 41 Montagem Caixa de aparelhagem dupla montagem embebida Mecanismo Acabamento Espelho Quadro Branco 7810 43 7719 00 Dark Bronze 7812 43 7719 10 Soft Alumínio 7813 43 7719 20 Titânio 7814 43 7719 30 Pérola 7815 43 7719 40 ST N TE LEAR Quadro 2 x 1 42 Referências de acessórios Espelho Legenda Botão LEARN: Tecla COMANDO : LEARN Sinalizador luminoso O sinalizador luminoso apaga-se O sinalizador luminoso pisca lentamente O sinalizador luminoso pisca rapidamente O sinalizador luminoso acende-se Memorização do cenário Emissor Sinalizador LEARN 1 Abrir o cenário 2 43 Receptor(es) Sinalizador LEARN Memorização do cenário (continuação) Emissor Sinalizador LEARN Receptor(es) Sinalizador LEARN 3 4 Para associar outros produtos ao cenário, repetir para cada receptor as operações 3 e 4. 5 Gravar o cenário O procedimento de memorização do cenário termina: a electroválvula será comandada e o circuito de água fechado logo que seja detectada uma fuga. 44 Modificação de um cenário Emissor Sinalizador LEARN Receptor(es) 1 Abrir o cenário 2 3 4 ou Para suprimir o produto do cenário voltar à 6. 45 Sinalizador LEARN Modificação de um cenário (continuação) Emissor Sinalizador LEARN Receptor(es) Sinalizador LEARN 5 6 Gravar o cenário Supressão de um cenário Suprimir todos os cenários ligados a este produto (no emissor) 1 2 5s 10 s 46 Problemas e soluções Problema Causa Solução O sinalizador LEARN acende-se durante 5 segundos. Não é possível efectuar o procedimento de memorização. Instalar produtos compatíveis. O sinalizador LEARN acende-se durante 10 segundos. O número de emissores associados é superior a 32. Suprimir os cenários em excesso. Durante o procedimento de memorização o sinalizador LEARN deixa de piscar. O modo de programação termina ao fim de 10 min (se não houver nenhuma acção). Recomeçar o procedimento de memorização. A tecla de comando não funciona. Depois de premido o botão LEARN, o período para efectuar a memorização da tecla de comando dura no máximo 1 min. Recomeçar o procedimento de memorização. Durante o procedimento de memorização de um cenário, o sinalizador LEARN de alguns receptores não se apaga. Comunicação deficiente entre os produtos. Verificar as ligações. Procurar a possível existência de um dispositivo perturbador (*) e isolá-lo através de um filtro. * Exemplo de dispositivos perturbadores : transformadores electrónicos, fontes de alimentação comutadas, etc. ( ) 47 Declaração de Conformidade DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY Nous déclarons que les produits satisfont aux dispositions de : We declare that the products satisfy the prov isions of : La Directive 1999/5/CE du Parlement européen et du Conseil du 9 mars 1999 "R&TTE" Directive 1999/5/EC of the European Parliament and of the Council of 9 march 1999 "R&TTE" sous réserve d'une utilisation conforme à sa destination et/ou d'une installation conforme aux normes en vigueur et/ou aux recommandations du constructeur on condition that they are used in the manner intended and/or in accordance with the current installation standards and/or with the manufacturer's recommandantions 48 Galea™ Life / Sistena Life Czujnik zalania 7756 77 Parametry techniczne U Ι 230 V~ 1 X 2,5 mm² / 2 X 1,5 mm² 0°C ... + 40°C 10 mA 20 mA 2 A 250 V~ / Moc maks 60 VA IP 30 85 dB (A) z odległości 1 m IK 04 Maksymalna długość czujnika < 1 m Media In One by Legrand PLC LE00517AA ST N TE LEAR 100 - 240 V~ 50/60 HZ 49 Część opisowa Brzęczyk LEARN Kontrolka wykrycia zalania (czerwona) Kontrolka LEARN (zielona) Kontrolka obecności napięcia (zielona) TEST Przycisk TEST Przycisk LEARN & Przycisk STEROWANIA uaktywniany przy drugim naciśnięciu Czujnik 50 Przyłączanie 1m maks. elektrozawór gazowy 51 Przepisy bezpieczeństwa Produkt ten powinien być montowany zgodnie z zasadami instalacji, najlepiej przez wykwalifikowanego elektryka. Niepoprawna instalacja lub złe użytkowanie mogą spowodować ryzyko porażenia prądem lub pożaru. Przed przystąpieniem do instalacji, zapoznać się z instrukcją i uwzględnić miejsce montażu urządzenia. Nie otwierać, nie demontować ani nie modyfikować urządzenia, jeśli nie ma na ten temat specjalnej wzmianki w instrukcji. Wszystkie produkty Legrand mogą być otwierane i naprawiane wyłącznie przez pracowników przeszkolonych i upoważnionych przez Legrand. Każde otwarcie lub naprawa dokonane bez odpowiedniego upoważnienia zwalnia Legrand od wszelkiej odpowiedzialności, powoduje utratę prawa do wymiany produktu i wygaśnięcie gwarancji. Używać wyłącznie oryginalnych części marki Legrand. 52 Działanie Podłączenie do prądu Kontrolka «obecności napięcia» zapala się na zielono Kontrolka «wykrycia zalania»" miga na żółto/czerwono przez kilka sekund, a następnie gaśnie Wykrycie płynu przewodzącego Kontrolka «wykrycia zalania» świeci się na czerwono.lub zwarcie czujnika, Wbudowany brzęczyk emituje przerywany dźwięk., Wewnętrzny przekaźnik zmienia stan, Polecenie ze scenariusza In One jest emitowane przez prąd nośny (PLC) do produktu lub produktów In One przypisanych w czasie zapamiętywania. Tryb TEST Poprzez przyciśnięcie przycisku TEST symuluje się wykrycie zalania aż do momentu puszczenia przycisku.(dostęp do przycisku TEST jest możliwy tylko po zdjęciu pokrywy). - Czujnik zalania jest kompatybilny ze sterownikiem scenariuszy symb. 7756 19. - Istnieje możliwość jego połączenia z urządzeniami radiowymi In One radio poprzez modułowy interfejs PLC/RF. Definicje Zapamiętywanie: procedura, która pozwala na zdefiniowanie i zapisanie scenariusza Scenariusz: wszystkie komendy wykonywane równolegle na różnych odbiornikach przypisanych do nadajnika w czasie zapamiętywania. 53 Montaż Puszka ścienna dwupunktowa Wykończenie Mechanizm Pokrywa Quadro Arktic 7810 43 7719 00 Choco 7812 43 7719 10 Metalic 7813 43 7719 20 Tytan 7814 43 7719 30 Opalis 7815 43 7719 40 ST N TE LEAR Płytka 2 x 1 54 Symbole akcesoriów Espelho Legenda Przycisk LEARN: Przycisk STEROWANIA : LEARN Kontrolka Kontrolka gaśnie Kontrolka miga wolno Kontrolka miga szybko ontrolka błyska Zapamiętywanie scenariusza Nadajnik Kontrolka LEARN 1 Otworzy_ scenariusz 2 55 Odbiornik(i) Kontrolka LEARN Zapamiętywanie scenariusza (ciag dalszy) Nadajnik Kontrolka LEARN Odbiornik(i) Kontrolka LEARN 3 4 Aby dodac kilka produktów do scenariusza, dla kaýdego odbiornika powtórzyc operacje 3 i 4. 5 Zapisac scenariusz Zapamietywanie jest zakonczone : elektrozawór bedzie sterowany, a obieg wody zostanie zamkniety w momencie wykrycia wycieku wody. 56 Modyfikacja scenariusza Nadajnik Kontrolka LEARN Odbiornik(i) 1 Otworzy_ scenariusz 2 3 4 lub Aby usunąć produkt ze scenariusza, przejść do 6. 57 Kontrolka LEARN Modyfikacja scenariusza (ciag dalszy) Nadajnik Kontrolka LEARN Odbiornik(i) Kontrolka LEARN 5 6 Zapisac scenariusz Usuwanie scenariusza Usunąć wszystkie scenariusze powiązane z tym produktem (na nadajniku) 1 2 5s 10 s 58 Problemy i ich rozwiązywanie Problem Przyczyna Rozwiązanie Kontrolka Learn świeci się przez 5 sekund. Zapamiętywanie jest niemożliwe. Zainstalować kompatybilne produkty Kontrolka Learn świeci się przez 10 sekund. Liczba zapisanych nadajników jest większa niż 32. Usunąć nieużywane scenariusze. W czasie zapamiętywania kontrolka Learn nie miga. Przy braku czynności, tryb zapamiętywania wyłącza się po 10 minutach. Ponownie rozpocząć zapamiętywanie. Przycisk programowania nie działa. Po wcisnieciu przycisku uczenia, uczenia przycisku funkcyjnego dokonano w nastepnej kolejnosci. Ponownie rozpocząć zapamiętywanie. Przy zapisywaniu scenariusza, kontrolki Learn niektórych odbiorników nie gasną. Zła komunikacja pomiędzy urządzeniami. Sprawdzić kable (podłączenia). Znaleźć urządzenie zakłócające (*). Odizolować je za pomocą filtra. * Przykad urzadzen ulegajacych interferencji : transformator elektroniczny, zasilacz elektroniczny,… ( ) 59 Deklaracja zgodność DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY Nous déclarons que les produits satisfont aux dispositions de : We declare that the products satisfy the prov isions of : La Directive 1999/5/CE du Parlement européen et du Conseil du 9 mars 1999 "R&TTE" Directive 1999/5/EC of the European Parliament and of the Council of 9 march 1999 "R&TTE" sous réserve d'une utilisation conforme à sa destination et/ou d'une installation conforme aux normes en vigueur et/ou aux recommandations du constructeur on condition that they are used in the manner intended and/or in accordance with the current installation standards and/or with the manufacturer's recommandantions 60
Documentos relacionados
Galea™ Life / Sistena Life Methane/butane-propane gas
Szenario: Alle Befehle, die gleichzeitig an den verschiedenen beim Einlernen mit dem Sender verknüpften Empfängern ausgeführt werden.
Leia maisWash cycles
orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the indicator light is switched off, the DOOR LOCKED door may be opened. To start the wash c...
Leia mais