Accreditation - MPA Braunschweig
Transcrição
Accreditation - MPA Braunschweig
Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-ZE-11267-01-00 according to DIN EN ISO/IEC 17065:2013 Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 Holder of certificate: Materialprüfanstalt für das Bauwesen, Braunschweig Beethovenstraße 52, 38106 Braunschweig Certification of products in the fields: Construction products for fire prevention (reaction to fire, resistance to fire, external fire performance), products for fire resistance and smoke control (smoke and heat exhaust ventilators, smoke control dampers and fire dampers plus coatings, penetration seals and joint seals, formation of fire section, cable and lines); construction products for the building shell (gypsum products, timber, wood-based panels, hydraulic binder and building limes, thermal insulation composite system, structural steel, products for masonry, floor coverings, shuttering kits, post tensioning kits, aggregates and filler for concrete and mortar, thermal insulation products, light composite wood-based beams and columns, precast concrete elements for load-bearing applications, kits for prefabricated timber frame building and log building, fibres for cement and mortar, kits for watertight floor- and wall coverings for wet rooms); construction products for the extension including additional requirements on the safety of use and usage (walling coverings discharge channel for traffic areas Mechanically fastened roof membranes, partition walls, roofing and accessories, wall cladding and ceiling coverings, liquid applied roof waterproofing kits, prefabricated stairs, sealing sheets, doors, windows, gates, building hardware); construction products for the strengthening and redevelopment of structures (surface protection systems for concrete elements and concrete substitute systems, injection materials, construction adhesives) Certification of construction products (systems of assessment and verification of constancy of performance 1 and 1+) and factory production control (system 2+) in accordance with the Construction Products Regulation (EU) No 305/2011 to defined harmonised conditions for the marketing of construction products (Construction Products Regulation - CPR) Abbreviations used: see last page This document is a translation. The definitive version is the original German annex to the accreditation certificate. Seite 1 von 39 Annex to the Accreditation Certificate D-ZE-11267-01-00 1 Construction products for fire protection Certification scheme MPA-BS 003 ,Products for fire resistance and smoke control‘ DIN EN 12101-1 2006-06 EN 12101-1 2005 +A1:2006 Rauch- und Wärmefreihaltung - Teil 1: Bestimmungen für Rauchschürzen Smoke and heat control systems - Part 1: Specification for smoke barriers DIN EN 12101-02 2003-09 EN 12101-2 2003 Rauch- und Wärmefreihaltung - Teil 2: Festlegungen für natürliche Rauch- und Wärmeabzugsgeräte Smoke and heat control systems - Part 2: Specification for natural smoke and heat exhaust ventilators DIN EN 12101-3 2015-12 EN 12101-3 2015 Rauch- und Wärmefreihaltung - Teil 3: Bestimmungen für maschinelle Rauch- und Wärmeabzugsgeräte Smoke and heat control systems - Part 3: Specification for powered smoke and heat exhaust ventilators DIN EN 12101-6 2005-09 EN 12101-6 2005 Rauch- und Wärmefreihaltung - Teil 6: Festlegungen für Differenzdrucksysteme, Bausätze Smoke and heat control systems - Part 6: Specification for pressure differential systems, Kits DIN EN 12101-7 2011-08 EN 12101-7 2011 Rauch- und Wärmefreihaltung - Teil 7: Entrauchungsleitungen Smoke and heat control systems - Part 7: Smoke duct sections DIN EN 12101-8 2011-08 EN 12101-8 2011 Rauch- und Wärmefreihaltung - Teil 8: Entrauchungsklappen Smoke and heat control systems - Part 8: Smoke control dampers DIN EN 15650 2010-09 EN 15650 2010 Lüftung von Gebäuden - Brandschutzklappen Ventilation for buildings - Fire dampers DIN EN 15871 2008-10 prEN 15871 2008 Lüftung von Gebäuden - Feuerwiderstandsfähige Leitungen Ventilation for buildings - Fire resisting duct sections Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 2/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 ISO 21927-1 2008-01 Rauch- und Wärmefreihaltung - Teil 1: Bestimmungen für Rauchschürzen Smoke and heat control systems - Part 1: Specification for smoke barriers ISO 21927-2 2006-11 ISO 21927-2 AMD 1 2010-06 Rauch- und Wärmefreihaltung - Teil 2: Festlegungen für natürliche Rauch- und Wärmeabzugsgeräte Smoke and heat control systems - Part 2: Specification for natural smoke and heat exhaust ventilators ISO 21927-3 2006-11 ISO 21927-3 AMD 1 2010-06 Rauch- und Wärmefreihaltung - Teil 3: Bestimmungen für maschinelle Rauch- und Wärmeabzugsgeräte Smoke and heat control systems - Part 3: Specification for powered smoke and heat exhaust ventilators in conjunction with: DIN EN 13501-3 2010-02 EN 13501-3 2005 +A1:2009 Klassifizierung von Bauprodukten und Bauarten zu ihrem Brandverhalten - Teil 3: Klassifizierung mit den Ergebnissen aus den Feuerwiderstandsprüfungen an Bauteilen von haustechnischen Anlagen - Feuerwiderstandsfähige Leitungen und Brandschutzklappen Fire classification of construction products and building elements - Part 3: Classification using data from fire resistance tests on products and elements used in building service installations: fire resisting ducts and fire dampers DIN EN 13501-4 2010-01 EN 13501-4 2007 +A1:2009 Klassifizierung von Bauprodukten und Bauarten zu ihrem Brandverhalten - Teil 4: Klassifizierung mit den Ergebnissen aus den Feuerwiderstandsprüfungen von Anlagen zur Rauchfreihaltung Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 3/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Certification scheme MPA-BS 027 ,fire protective products‘ ETAG 018-1 2004 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte (Brandschutzbekleidungen und Brandschutzbeschichtungen) - Teil 1: Allgemeines Guideline for European Technical Approval of fire protective products - Part 1: General ETAG 018-2 2006 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte (Brandschutzbekleidungen und Brandschutzbeschichtungen) - Teil 2: Reaktive Brandschutzbeschichtungen auf Stahlbauteilen Guideline for European Technical Approval of fire protective products - Part 2: Reactive Coatings for Fire Protection of Steel Elements ETAG 018-3 2006 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte (Brandschutzbekleidungen und Brandschutzbeschichtungen) - Teil 3: Brandschutzputzbekleidungen mit und ohne Putzträger und Bausätze für Brandschutzbekleidungen zur Verwendung als Brandschutzprodukt Guideline for European Technical Approval of fire protective products Part 3: Renderings and Rendering Kits intended for Fire Resisting Applications ETAG 018-4 2004 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte (Brandschutzbekleidungen und Brandschutzbeschichtungen) - Teil 4: Produkte und Bausätze aus verformbaren und nicht verformbaren Brandschutzplatten und aus Brandschutzmatten Guideline for European Technical Approval of fire protective products - Part 4: Fire protective board, slab and mat products and kits ETAG 026-1 2008 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte zum Abdichten und Verschließen von Fugen und Öffnungen und zum Aufhalten von Feuer im Brandfall - Teil 1: Allgemeines Guideline for European Technical Approval of fire stopping and fire sealing products - Part 1: General Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 4/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 ETAG 026-2 2008 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte zum Abdichten und Verschließen von Fugen und Öffnungen und zum Aufhalten von Feuer im Brandfall - Teil 2: Abschottungen Guideline for European Technical Approval of fire stopping and fire sealing products - Part 2: Penetration Seals ETAG 026-3 2008 Leitlinie für die Europäische Technische Zulassung für Brandschutzprodukte zum Abdichten und Verschließen von Fugen und Öffnungen und zum Aufhalten von Feuer im Brandfall - Teil 3: Linienförmige Fugenabdichtungen und Brandsperren Guideline for European Technical Approval of fire stopping and fire sealing products - Part 3: Linear Joint and Gap Seals DIN EN 50575 2015-04 EN 50575 2014 Starkstromkabel und –leitungen, Steuer- und Kommunikationskabel – Kabel und Leitungen für allgemeine Anwendungen in Bauwerken in Bezug auf die Anforderungen an das Brandverhalten Power, control and communication cables - Cables for general applications in construction works subject to reaction to fire requirements EAD 3500005-00-1104 Intumescent products for fire sealing and fire stopping in conjunction with: DIN EN 13501-1 2010-01 EN 13501-1 2007 +A1:2009 Klassifizierung von Bauprodukten und Bauarten zu ihrem Brandverhalten - Teil 1: Klassifizierung mit den Ergebnissen aus den Prüfungen zum Brandverhalten von Bauprodukten Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests DIN EN 13501-2 2010-02 EN 13501-2 2007 +A1:2009 Klassifizierung von Bauprodukten und Bauarten zu ihrem Brandverhalten - Teil 2: Klassifizierung mit den Ergebnissen aus den Feuerwiderstandsprüfungen, mit Ausnahme von Lüftungsanlagen Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 5/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Bauprodukte für den Rohbau Zertifizierungsprogramm MPA-BS 001 ,Gipsprodukte‘ DIN EN 520 2009-12 EN 520 2004 +A1:2009 Gipsplatten - Begriffe, Anforderungen und Prüfverfahren – Gypsum plasterboards - Definitions, requirements and test methods EN 12859 2011-05 EN 12859 2011 Gips-Wandbauplatten - Begriffe, Anforderungen und Prüfverfahren Gypsum blocks - Definitions, requirements and test methods DIN EN 12860 2002-07 EN 12860 2001 +AC:2002 Gipskleber für Gips-Wandbauplatten - Begriffe, Anforderungen und Prüfverfahren Gypsum based adhesives for gypsum blocks - Definitions, requirements and test methods DIN EN 13815 2006-12 EN 13815 2006 Formteile aus faserverstärktem Gips - Begriffe, Anforderungen und Prüfverfahren Fibrous gypsum plaster casts - Definitions, requirements and test methods DIN EN 13915 2007-11 EN 13915 2007 Gipsplatten-Wandbaufertigtafeln mit einem Kartonwabenkern Begriffe, Anforderungen und Prüfverfahren Prefabricated gypsum plasterboard panels with a cellular paperboard core - Definitions, requirements and test methods DIN EN 13950 2006-02 EN 13950 2005 Gips-Verbundplatten zur Wärme- und Schalldämmung - Begriffe, Anforderungen und Prüfverfahren Gypsum plasterboard thermal/acoustic insulation composite panels - Definitions, requirements and test methods DIN EN 13963 2006-11 EN 13963 2005/AC:2006 Materialien für das Verspachteln von GipsplattenFugen - Begriffe, Anforderungen und Prüfverfahren Jointing materials for gypsum plasterboards - Definitions, requirements and test methods DIN EN 14190 2005-11 EN 14190 2005 Gipsplattenprodukte aus der Weiterverarbeitung - Begriffe, Anforderungen und Prüfverfahren Gypsum plasterboard products from reprocessing - Definitions, requirements and test methods Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 6/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14209 2006-02 EN 14209 2005 Hohlkehlleisten aus kartonummanteltem Gips - Begriffe, Anforderungen und Prüfverfahren Preformed plasterboard cornices - Definitions, requirements and test methods version DIN EN 14246 2006-09 EN 14246 2006 Gipselemente für Unterdecken (abgehängte Decken) - Begriffe, Anforderungen und Prüfverfahren Gypsum elements for suspended ceilings - Definitions, requirements and test methods DIN EN 14496 2006-02 EN 14496 2005 Kleber auf Gipsbasis für Verbundplatten zur Wärme- und Schalldämmung und Gipsplatten - Begriffe, Anforderungen und Prüfverfahren Gypsum based adhesives for thermal/acoustic insulation composite panels and plasterboards - Definitions, requirements and test methods EN 15283-1 2009-12 EN 15283-1 2008 +A1:2009 Faserverstärkte Gipsplatten - Begriffe, Anforderungen und Prüfverfahren - Teil 1: Gipsplatten mit Vliesarmierung Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement EN 15283-2 2009-12 EN 15283-2 2008 +A1:2009 Faserverstärkte Gipsplatten - Begriffe, Anforderungen und Prüfverfahren - Teil 2: Gipsfaserplatten Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 2: Gypsum fibre boards EAD 070001-00-0504 Gypsum plasterboard for load bearing applications Certification scheme MPA-BS 005 ,Timber for load-bearing purposes ‘ DIN EN 14080 2013-09 EN 14080 2013 Holzbauwerke - Brettschichtholz - Anforderungen Timber structures - Glued laminated timber and glued solid timber Requirements DIN EN 14081-1 2011-05 EN 14081-1 2005 +A1:2011 Holzbauwerke - Nach Festigkeit sortiertes Bauholz für tragende Zwecke mit rechteckigem Querschnitt - Teil 1: Allgemeine Anforderungen Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 7/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14250 2010-05 EN 14250 2010 Holzbauwerke - Produktanforderungen an vorgefertigte tragende Bauteile mit Nagelplattenverbindungen Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners Certification scheme MPA-BS 006 ,Wood-based panels‘ DIN EN 13986 2015-06 EN 13986 2004+A1:2015 Holzwerkstoffe zur Verwendung im Bauwesen - Eigenschaften, Bewertung der Konformität und Kennzeichnung Wood-based panels for use in construction - Characteristics, evaluation of conformity and marking Certification scheme MPA-BS 008 ,Hydraulic binder and building limes‘ DIN EN 197-1 2011-11 EN 197-1 2011 Zement - Teil 1: Zusammensetzung, Anforderungen und Konformitätskriterien von Normalzement Cement - Part 1: Composition, specifications and conformity criteria for common cements DIN EN 197-4 2004-08 EN 197-4 2004 Zement - Teil 4: Zusammensetzung, Anforderungen und Konformitätskriterien von Hochofenzement mit niedriger Anfangsfestigkeit Cement - Part 4: Composition, specifications and conformity criteria for low early strength blastfurnace cements DIN EN 413-1 2011-07 EN 413-1 2011 Putz- und Mauerbinder - Teil 1: Zusammensetzung, Anforderungen und Konformitätskriterien Masonry cement - Part 1: Composition, specifications and conformity criteria DIN EN 450-1 2012-10 EN 450-1 2012 Flugasche für Beton - Teil 1: Definition, Anforderungen und Konformitätskriterien Fly ash concrete - Part 1: Definition, specifications and conformity criteria DIN EN 459-1 2010-12 EN 459-1 2010 Baukalk - Teil 1: Begriffe, Anforderungen und Konformitätskriterien Building lime - Part 1: Definitions, specifications and conformity criteria DIN EN 14216 2004-08 EN 14216 2004 Zement - Zusammensetzung, Anforderungen und Konformitätskriterien von Sonderzement mit sehr niedriger Hydratationswärme Cement - Composition, specifications and conformity criteria for very low heat special cements Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 8/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14647 2006-01 EN 14647 2005 Tonerdezement - Zusammensetzung, Anforderungen und Konformitätskriterien Calcium aluminate cement - Composition, specifications and conformity criteria DIN EN 15167-1 2006-12 EN 15167-1 2006 Hüttensandmehl zur Verwendung in Beton, Mörtel und Einpressmörtel - Teil 1: Definitionen, Anforderungen und Konformitätskriterien Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria Certification scheme MPA-BS 009 ,Thermal insulation composite systems with rendering‘ ETAG 004 2000 Leitlinie für Europäische Technische Zulassungen für außenseitige Wärmedämm-Verbundsysteme mit Putzschicht Guideline for European Technical Approval of external thermal insulation composite systems with rendering Certification scheme MPA-BS 010 , Structural steel ‘ DIN EN 10025-1 2005-2 EN 10025-1 2004 Warmgewalzte Erzeugnisse aus Baustählen - Teil 1: Allgemeine technische Lieferbedingungen Hot rolled products of structural steels - Part 1: General technical delivery conditions DIN EN 10088-5 2009-07 EN 10088-5 2009 Nichtrostende Stähle - Teil 5: Technische Lieferbedingungen für Stäbe, Walzdraht, gezogenen Draht, Profile und Blankstahlerzeugnisse aus korrosionsbeständigen Stählen für das Bauwesen Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes Certification scheme MPA-BS 011 ,Products for masonry‘ DIN EN 771-1 2011-07 EN 771-1 2011 Festlegungen für Mauersteine - Teil 1: Mauerziegel Specification for masonry units - Part 1: Clay masonry units DIN EN 771-2 2011-07 EN 771-2 2011 Festlegungen für Mauersteine - Teil 2: Kalksandsteine Specification for masonry units - Part 2: Calcium silicate masonry units Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 9/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 771-3 2011-07 EN 771-3 2011 Festlegungen für Mauersteine - Teil 3: Mauersteine aus Beton (mit dichten und porigen Zuschlägen) Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates) DIN EN 771-4 2011-07 EN 771-4 2011 Festlegungen für Mauersteine - Teil 4: Porenbetonsteine Specification for masonry units - Part 4: Autoclaved aerated concrete masonry units DIN EN 771-5 2011-07 EN 771-5 2011 Festlegungen für Mauersteine - Teil 5: Betonwerksteine Specification for masonry units - Part 5: Manufactured stone masonry units DIN EN 771-6 2011-07 EN 771-6 2011 Festlegungen für Mauersteine - Teil 6: Natursteine Specification for masonry units - Part 6: Natural stone masonry units DIN EN 845-1 2008-06 EN 845-1 2003 +A1:2008 Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 1: Maueranker, Zugbänder, Auflager und Konsolen Specification for ancillary components for masonry - Part 1: Ties, tension straps, hangers and brackets DIN EN 845-2 2003-08 EN 845-2 2003 Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 2: Stürze Specification for ancillary components for masonry - Part 2: Lintels DIN EN 845-3 2008-06 EN 845-3 2003 +A1:2008 Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 3: Lagerfugenbewehrung aus Stahl Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork DIN EN 998-1 2010-12 EN 998-1 2010 Festlegungen für Mörtel im Mauerwerksbau - Teil 1: Putzmörtel Specification for mortar for masonry - Part 1: Rendering and plastering mortar DIN EN 998-2 2010-12 EN 998-2 2010 Festlegungen für Mörtel im Mauerwerksbau - Teil 2: Mauermörtel Specification for mortar for masonry - Part 2: Masonry mortar Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 10/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Certification scheme MPA-BS 012 ,Floor coverings‘ DIN EN 13454-1 2005-01 EN 13454-1 2004 Calciumsulfat-Binder, Calciumsulfat-Compositbinder und Calciumsulfat-Werkmörtel für Estriche - Teil 1: Begriffe und Anforderungen Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate - Part 1: Definitions and requirements DIN EN 13813 2003-01 EN 13813 2002 Estrichmörtel, Estrichmassen und Estriche - Estrichmörtel und Estrichmassen - Eigenschaften und Anforderungen Screed material and floor screeds - Screed materials - Properties and requirements Certification scheme MPA-BS 015 ,Shuttering kits‘ ETAG 009 2002 Leitlinie für nicht lasttragende verlorene Schalungsbausätze/ -systeme bestehend aus Schalungs-/Mantelsteinen oder -elementen aus Wärmedämmstoffen und - mitunter - aus Beton Guideline for European Technical Approval of non load-bearing permanent shuttering kits/systems based on hollow blocks or panels of insulating materials and sometimes concrete Certification scheme MPA-BS 018 ,Post tensioning kits‘ ETAG 013 2002 Leitlinie für die Europäische Technische Zulassung für Bausätze zur Vorspannung von Tragwerken Guideline for European Technical Approval of post tensioning kits for prestressing of structures Certification scheme MPA-BS 019 ,Aggregates and filler for concrete and mortar‘ DIN EN 12620 2008-07 EN 12620 2002 +A1:2008 Gesteinskörnungen für Beton Aggregates for concrete DIN EN 13043 2002-12 + Berichtigung 1 2004-12 EN 13043 2002 Gesteinskörnungen für Asphalt und Oberflächenbehandlungen für Straßen, Flugplätze und andere Verkehrsflächen Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 11/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 13055-1 2002-08 + Berichtigung 1 2004-12 EN 13055-1 2002 Leichte Gesteinskörnungen - Teil 1: Leichte Gesteinskörnungen für Beton, Mörtel und Einpressmörtel Lightweight aggregates - Part 1: Lightweight aggregates for concrete, mortar and grout DIN EN 13055-2 2004-09 EN 13055-2 2004 Leichte Gesteinskörnungen - Teil 2: Leichte Gesteinskörnungen für Asphalte und Oberflächenbehandlungen sowie für ungebundene und gebundene Verwendung Lightweight aggregates - Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications DIN EN 13139 2002-08 + Berichtigung 1 2004-12 EN 13139 2002 Gesteinskörnungen für Mörtel Aggregates for mortar EN 13242 2008-03 EN 13242 2002 +A1:2007 Gesteinskörnungen für ungebundene und hydraulisch gebundene Gemische für den Ingenieur- und Straßenbau Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction Certification scheme MPA-BS 023 ,Thermal insulation products‘ DIN EN 13162 2015-04 EN 13162 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Mineralwolle (MW) - Spezifikation Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification DIN EN 13163 2015-04 EN 13163 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation Thermal insulation products for buildings - Factory made products of expanded polystyrene (EPS) – Specification DIN EN 13164 2015-04 EN 13164 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) - Specification Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 12/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 13165 2015-04 EN 13165 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PUR) - Spezifikation Thermal insulation products for buildings - Factory made rigid polyurethane foam (PUR) products – Specification DIN EN 13166 2015-04 EN 13166 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Phenolharzschaum (PF) - Spezifikation Thermal insulation products for buildings - Factory made products of phenolic foam (PF) – Specification DIN EN 13167 2015-04 EN 13167 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Schaumglas (CG) - Spezifikation Thermal insulation products for buildings - Factory made cellular glass (CG) products – Specification DIN EN 13168 2015-04 EN 13168 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Holzwolle (WW) - Spezifikation Thermal insulation products for buildings - Factory made wood wool (WW) products – Specification DIN EN 13169 2015-04 EN 13169 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Blähperlit (EPB) - Spezifikation Thermal insulation products for buildings - Factory made products of expanded perlite (EPB) - Specification DIN EN 13170 2015-04 EN 13170 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Kork (ICB) - Spezifikation Thermal insulation products for buildings - Factory made products of expanded cork (ICB) – Specification DIN EN 13171 2015-04 EN 13171 2012+A1:2015 Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Holzfasern (WF) - Spezifikation Thermal insulating products for buildings - Factory made wood fibre (WF) products - Specification DIN EN 14303 2013-04 EN 14303 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Mineralwolle (MW) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products Specification Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 13/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14304 2013-04 EN 14304 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus flexiblem Elastomerschaum (FEF) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products; Specification DIN EN 14305 2013-04 EN 14305 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Schaumglas (CG) - Spezifikation Thermal insulation products for building equipment and industrial installlations - Factory made cellular glass (CG) products – Specification DIN EN 14306 2013-04 EN 14306 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Calciumsilikat (CS) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products – Specification DIN EN 14307 2013-04 EN 14307 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products – Specification DIN EN 14308 2013-04 EN 14308 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PUR) und Polyisocyanurat-Schaum (PIR) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products – Specification DIN EN 14309 2013-04 EN 14309 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 14/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14313 2013-04 EN 14313 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Polyethylenschaum (PEF) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products Specification DIN EN 14314 2013-04 EN 14314 2009 +A1:2013 Wärmedämmstoffe für die technische Gebäudeausrüstsung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Phenolharzschaum (PF) - Spezifikation Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification DIN EN 14316-1 2004-11 EN 14316-1 2004 Wärmedämmstoffe für Gebäude - An der Verwendungsstelle hergestellte Wärmedämmung aus Produkten mit expandiertem Perlite (EP) - Teil 1: Spezifikation für gebundene und Schüttdämmstoffe vor dem Einbau Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation DIN EN 14317-1 2004-11 EN 14317-1 2004 Wärmedämmstoffe für Gebäude; an der Verwendungsstelle hergestellte Wärmedämmung mit Produkten aus expandiertem Vermiculite (EV) - Teil 1: Spezifikation für gebundene und Schüttdämmstoffe vor dem Einbau Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation DIN EN 14933 2007-12 EN 14933 2007 Wärmedämmung und leichte Füllprodukte für Anwendungen im Tiefbau - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation Thermal insulation and light weigth fill products for civil engineering applications - Factory made products of expanded polystyrene (EPS) – Specification DIN EN 14934 2007-12 EN 14934 2007 Wärmedämmung und leichte Füllprodukte für Anwendungen im Tiefbau - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 15/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 15599-1 2010-12 EN 15599-1 2010 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - An der Verwendungsstelle hergestellte Wärmedämmung mit Produkten aus expandiertem Perlit (EP) - Teil 1: Spezifikation für gebundene und Schüttprodukte vor dem Einbau Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation DIN EN 15600-1 2010-12 EN 15600-1 2010 Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - An der Verwendungsstelle hergestellte Wärmedämmung mit Produkten aus expandiertem Vermiculit (EV) - Teil 1: Spezifikation für gebundene und Schüttprodukte vor dem Einbau Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation Certification scheme MPA-BS 024 ,Light composite wood-based beams and columns‘ ETAG 011 2011 Leitlinie für die Europäische Technische Zulassung für leichte Holzbauträger und -stützen Guideline for European Technical Approval of light composite woodbased beams and columns Certification scheme MPA-BS 026 ,Precast concrete products for load-bearing applications‘ DIN EN 1168 2011-12 EN 1168 2005 +A3:2011 Betonfertigteile - Hohlplatten Precast concrete products - Hollow core slabs DIN EN 1520 2011-06 EN 1520 2011 Vorgefertigte bewehrte Bauteile aus haufwerksporigem Leichtbeton Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement DIN EN 12737 2008-02 EN 12737 2004 +A1:2007 Betonfertigteile - Spaltenböden für die Tierhaltung Precast concrete products - Floor slats for livestock Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 16/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 12794 2009-04 EN 12794 2005 +A1:2007/AC:2008 Betonfertigteile - Gründungspfähle Precast concrete products - Foundation piles DIN EN 12843 2004-11 EN 12843 2004 Betonfertigteile - Maste Precast concrete products - Masts and poles DIN EN 13224 2012-01 EN 13224 2011 Betonfertigteile - Deckenplatten mit Stegen Precast concrete products - Ribbed floor elements DIN EN 13225 2013-06 EN 13225 2013 Betonfertigteile - Stabförmige tragende Bauteile Precast concrete products - Linear structural elements DIN EN 13693 2009-10 EN 13693 2004 +A1:2009 Betonfertigteile - Besondere Fertigteile für Dächer Precast concrete products - Special roof elements DIN EN 13747 2010-08 EN 13747 2005 +A2:010 Betonfertigteile - Deckenplatten mit Ortbetonergänzung Precast concrete products - Floor plates for floor systems DIN EN 13978-1 2005-07 EN 13978-1 2005 Betonfertigteile - Betonfertiggaragen - Teil 1: Anforderungen an monolithische oder aus raumgroßen Einzelteilen bestehende Stahlbetongaragen Precast concrete products - Precast concrete garages - Part 1: Requirements for reinforced garages monolithic or consisting of single sections with room dimensions DIN EN 14843 2007-07 EN 14843 2007 Betonfertigteile - Treppen Precast concrete products - Stairs DIN EN 14844 2012-02 EN 14844 2006 +A2:2011 Betonfertigteile - Hohlkastenelemente Precast concrete products - Box culverts Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 17/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14991 2007-07 EN 14991 2007 Betonfertigteile - Gründungselemente Precast concrete products - Foundation elements DIN EN 14992 2012-09 EN 14992 2007 +A1:2012 Betonfertigteile - Wandelemente Precast concrete products - Wall elements DIN EN 15037-1 2008-07 EN 15037-1 2008 Betonfertigteile - Balkendecken mit Zwischenbauteilen - Teil 1: Balken Precast concrete products - Beam-and-block floor systems - Part 1: Beams DIN EN 15037-2 2011-07 EN 15037-2 2009 +A1:2011 Betonfertigteile - Balkendecken mit Zwischenbauteilen - Teil 2: Zwischenbauteile aus Beton Precast concrete products - Beam-and-block floor systems - Part 2: Concrete blocks DIN EN 15037-4 2010-05 EN 15037-4 2010 Betonfertigteile - Balkendecken mit Zwischenbauteilen - Teil 4: Zwischenbauteile aus Polystyrolhartschaum Precast concrete products - Beam-and-block floor systems - Part 4: Expanded polystyrene blocks DIN EN 15050 2012-06 EN 15050 2007 +A1:2012 Betonfertigteile - Fertigteile für Brücken Precast concrete products - Bridge elements DIN EN 15258 2009-05 EN 15258 2008 Betonfertigteile - Stützwandelemente Precast concrete products - Retaining wall elements Certification scheme MPA-BS 028 ,Kits for prefabricated timber frame building and log building‘ ETAG 007 2001 Leitlinie für die Europäische Technische Zulassung für Bausätze für den Holzrahmenbau Guideline for European Technical Approval of Timber Frame Building Kits ETAG 012 2002 Leitlinie für die Europäische Technische Zulassung für Bausätze für Blockhäuser Guideline for European Technical Approval of Log Building Kits Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 18/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Certification scheme MPA-BS 029 , Fibres for concrete and mortar‘ EN 14889-1 2006-11 EN 14889-1 2006 Fasern für Beton - Teil 1: Stahlfasern - Begriffe, Festlegungen und Konformität Fibres for concrete - Part 1: Steel fibres - Definitions, specifications and conformity DIN EN 14889-2 2006-11 EN 14889-2 2006 Fasern für Beton - Teil 2: Polymerfasern - Begriffe, Festlegungen und Konformität Fibres for concrete - Part 2: Polymer fibres - Definitions, specifications and conformity Certification scheme MPA-BS 032 ,Kits for watertight floor- and wall coverings for wet rooms‘ ETAG 022-1 2007 Leitlinie für die Europäische Technische Zulassung für Abdichtungen für Wände und Böden in Nassräumen - Teil 1: Flüssig aufzubringende Abdichtungen mit oder ohne Nutzschicht – Guideline for European Technical Approval of watertight covering kits for wetroom floors and/or walls - Part 1: Liquid applied coverings with or without wearing surface ETAG 022-2 2011 Leitlinie für die Europäische Technische Zulassung für Abdichtungen für Wände und Böden in Nassräumen - Teil 2: Bausätze mit Abdichtungsbahnen Guideline for European Technical Approval of watertight covering kits for wetroom floors and/or walls - Part 2: Kits based on flexible sheets ETAG 022-3 2011 Leitlinie für die Europäische Technische Zulassung für Abdichtungen für Wände und Böden in Nassräumen - Teil 3: Bausätze mit wasserdichten Platten Guideline for European Technical Approval of watertight covering kits for wetroom floors and/or walls - Part 3: Kits based on inherently watertight boards Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 19/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 2 Construction products for the extension including additional requirements on the safety of use and usage Certification scheme MPA-BS 004 ,Walling coverings‘ DIN EN 13830 2003-11 EN 13830 2003 Vorhangfassaden - Produktnorm Curtain walling - Product standard Certification scheme MPA-BS 007 ,Discharge channel for traffic areas‘ DIN EN 1433 2005-09 EN 1433 2002 +AC:2004 +A1:2005 Entwässerungsrinnen für Verkehrsflächen - Klassifizierung, Bau- und Prüfgrundsätze, Kennzeichnung und Beurteilung der Konformität Drainage channels for vehicular and pedestrian areas Classification, design and testing requirements, marking and evaluation of conformity Certification scheme MPA-BS 013 ,Mechanically fastened roof membranes ‘ ETAG 006 2000 Leitlinie für Europäische Technische Zulassungen von mechanisch befestigten Dachabdichtungen Guideline for European Technical Approval of systems of mechanically fastened flexible roof Waterproofing membranes Certification scheme MPA-BS 014 ‚Partition walls‘ ETAG 003 1999 Leitlinie für die Europäische Technische Zulassung für Bausätze für innere Trennwände zur Verwendung als nichttragende Wände Guideline for European Technical Approval of internal partition kits for use as non-loadbearing walls Certification scheme MPA-BS 016 ‚Roofing and accessories‘ DIN EN 490 2012-01 EN 490 2011 Dach- und Formsteine aus Beton für Dächer und Wandbekleidungen; Produktanforderungen Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 20/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 492 2012-12 EN 492 2012 Faserzement-Dachplatten und dazugehörige Formteile - Produktspezifikation und Prüfverfahren – Fibre cement slates and fittings - Product specification and test methods DIN EN 494 2013-01 EN 494 2012 Faserzement-Wellplatten und dazugehörige Formteile - Produktspezifikation und Prüfverfahren - Fibre-cement profiled sheets and fittings - Product specification and test methods DIN EN 1304 2008-07 EN 1304 2005 Dachziegel und Formziegel - Begriffe und Produktanforderungen Clay roofing tiles and fittings - Product definitions and specifications Certification scheme MPA-BS 017 ‚Wall cladding and ceiling coverings‘ DIN EN 490 2012-01 EN 490 2011 Dach- und Formsteine aus Beton für Dächer und Wandbekleidungen - Produktanforderungen Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications DIN EN 492 2012-12 EN 492 2012 Faserzement-Dachplatten und dazugehörige Formteile - Produktspezifikation und Prüfverfahren Fibre cement slates and fittings - Product specification and test methods DIN EN 494 2013-01 EN 494 2012 Faserzement-Wellplatten und dazugehörige Formteile - Produktspezifikation und Prüfverfahren - Fibre-cement profiled sheets and fittings - Product specification and test methods DIN EN 1304 2008-07 EN 1304 2005 Dachziegel und Formziegel - Begriffe und Produktanforderungen Clay roofing tiles and fittings - Product definitions and specifications DIN EN 12467 2012-12 EN 12467 2012 Faserzement-Tafeln - Produktspezifikation und Prüfverfahren Fibre cement flat sheets - Product specification and test methods DIN EN 13964 2014-08 EN 13964 2014 Unterdecken - Anforderungen und Prüfverfahren Suspended ceilings - Requirements and test methods Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 21/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 14509 2013-12 EN 14509 2013 Selbsttragende Sandwich-Elemente mit beidseitigen Metalldeckschichten - Werkmäßig hergestellte Produkte – Spezifikationen Self-supporting double skin metal faced insulating panels - Factory made products - Specification DIN EN 14716 2005-03 EN 14716 2004 Spanndecken - Anforderungen und Prüfverfahren Stretched ceilings - Requirements and tests methods Certification scheme MPA-BS 020 ‚Liquid applied roof waterproofing kits‘ ETAG 005 2005 Leitlinie für die Europäische Technische Zulassung für flüssig aufzubringende Dachabdichtungen Guideline for European Technical Approval of liquid applied roof waterproofing kit Certification scheme MPA-BS 021 ‚Prefabricated stair‘ ETAG 008 2002 Leitlinie für Europäische Technische Zulassungen für vorgefertigte Treppenbausätze - Vorgefertigte Treppenbausätze im Allgemeinen (mit Ausnahme von erschwerenden klimatischen Beanspruchungen) Guideline for European Technical Approval of prefabricated stair kits - Prefabricated stair kits in general (excluding severe climatic conditions) Certification scheme MPA-BS 022 ‚Sealing sheets‘ DIN EN 13707 2009-10 EN 13707 2004 +A2:2009 Abdichtungsbahnen - Bitumenbahnen mit Trägereinlage für Dachabdichtungen - Definitionen und Eigenschaften Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics DIN EN 13859-1 2010-11 EN 13859-1 2010 Abdichtungsbahnen - Definitionen und Eigenschaften von Unterdeck- und Unterspannbahnen - Teil 1: Unterdeck- und Unterspannbahnen für Dachdeckungen Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 1: Underlays for discontinuous roofing Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 22/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 13859-2 2010-11 EN 13859-2 2010 Abdichtungsbahnen - Definitionen und Eigenschaften von Unterdeck- und Unterspannbahnen - Teil 2: Unterdeck- und Unterspannbahnen für Wände Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 2: Underlays for walls DIN EN 13956 2013-03 EN 13956 2012 Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für Dachabdichtungen - Definitionen und Eigenschaften Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics DIN EN 13967 2012-07 EN 13967 2012 Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für die Bauwerksabdichtung gegen Bodenfeuchte und Wasser - Definitionen und Eigenschaften Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet Definitions and characteristics DIN EN 13969 2007-03 EN 13969 2004 +A1:2006 Abdichtungsbahnen - Bitumenbahnen für die Bauwerksabdichtung gegen Bodenfeuchte und Wasser - Definitionen und Eigenschaften Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics DIN EN 13970 2007-02 EN 13970 2004/A1:2006 Abdichtungsbahnen - Bitumen-Dampfsperrbahnen - Definitionen und Eigenschaften Flexible sheets for waterproofing - Bitumen water vapour control layers - Definitions and characteristics DIN EN 13984 2013-05 EN 13984 2013 Abdichtungsbahnen - Kunststoff- und Elastomer-Dampfsperrbahnen Definitionen und Eigenschaften Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics DIN EN 14909 2012-07 EN 14909 2012 Abdichtungsbahnen - Kunststoff- und Elastomer-Mauersperrbahnen Definitionen und Eigenschaften Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics DIN EN 14967 2006-08 EN 14967 2006 Abdichtungsbahnen - Bitumen-Mauersperrbahnen - Definitionen und Eigenschaften – Flexible sheets for waterproofing - Bitumen damp proof courses Definitions and characteristics Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 23/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Certification scheme MPA-BS 025 ‚Doors, windows, gates and hardware‘ DIN EN 179 2008-04 EN 179 2008 Schlösser und Baubeschläge - Notausgangsverschlüsse mit Drücker oder Stoßplatte für Türen in Rettungswegen - Anforderungen und Prüfverfahren Building hardware - Emergency exit devices operated by a lever handle or push pad, for use on escape routes - Requirements and test methods DIN EN 1125 2008-04 EN 1125 2008 Schlösser und Baubeschläge - Paniktürverschlüsse mit horizontaler Betätigungsstange für Türen in Rettungswegen - Anforderungen und Prüfverfahren Building hardware - Panic exit devices operated by a horizontal bar, for use on escape routes - Requirements and test methods DIN EN 1154 2003-04 EN 1158 1997 +A1:2002 Schlösser und Baubeschläge - Türschließmittel mit kontrolliertem Schließablauf - Anforderungen und Prüfverfahren Building hardware - Door coordinator devices - Requirements and test methods DIN EN 1935 2002-05 EN 1935 2002 Baubeschläge - Einachsige Tür- und Fensterbänder - Anforderungen und Prüfverfahren Building hardware - Single-axis hinges - Requirements and test methods DIN EN 12209 2006-06 EN 12209 2003/AC:2005 Schlösser und Baubeschläge - Schlösser - Mechanisch betätigte Schlösser und Schließbleche - Anforderungen und Prüfverfahren Building hardware - Locks and latches - Mechanically operated locks, latches and locking plates - Requirements and test methods DIN EN 13241-1 2011-06 EN 13241-1 2003 +A1:2011 Tore - Produktnorm - Teil 1: Produkte ohne Feuer- und Rauchschutzeigenschaften Industrial, commercial and garage doors and gates - Product standard - Part 1: Products without fire resistance or smoke control characteristics DIN EN 14351-1 2010-08 EN 14351-1 2006 +A1:2010 Fenster und Türen - Produktnorm, Leistungseigenschaften - Teil 1: Fenster und Außentüren ohne Eigenschaften bezüglich Feuerschutz und/oder Rauchdichtheit Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 24/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 16034 2014-12 EN 16034 2014 3 Türe, Tore und Fenster - Produktnorm, Leistungseigenschaften Feuer- und/oder Rauchschutzeigenschaften Pedestrian doorsets, industrial, commercial, garage doors and openable windows - Product standard, performance characteristics Fire resistance and/or smoke control characteristics Construction products for strengthening and redevelopment Certification scheme MPA-BS 030 ‚Surface protection systems for concrete and concrete substitute systems‘ DIN EN 1504-2 2005-01 EN 1504-2 2004 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete DIN EN 1504-3 2006-03 EN 1504-3 2005 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 3: Statisch und nicht statisch relevante Instandsetzung Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 3: Structural and non-structural repair DIN EN 1504-4 2005-02 EN 1504-4 2004 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 4: Kleber für Bauzwecke Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 4: Structural bonding DIN EN 1504-5 2013-06 EN 1504-5 2013 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 5: Injektion von Betonbauteilen - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 25/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 1504-6 2006-11 EN 1504-6 2006 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 6: Verankerung von Bewehrungsstäben Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 6: Anchoring of reinforcing steel bar DIN EN 1504-7 2006-11 EN 1504-7 2006 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 7: Korrosionsschutz der Bewehrung Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 7: Reinforcement corrosion protection in conjunction with: DIN EN 1504-1 2005-10 EN 1504-1 2005 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken Definitionen, Anforderungen, Güteüberwachung und Beurteilung der Konformität Teil 1: Definitionen Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions DIN EN 1504-8 2005-02 EN 1504-8 2004 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 8: Qualitätsüberwachung und Beurteilung der Konformität Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity - Part 8: Quality control and evaluation of conformity Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 26/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 DIN EN 1504-9 2008-11 EN 1504-9 2008 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 9: Allgemeine Grundsätze für die Anwendung von Produkten und Systemen Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity - Part 9: General principles for the use of products and systems DIN EN 1504-10 2006-10 EN 1504-10 2003/AC:2005 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 10: Anwendung von Stoffen und Systemen auf der Baustelle, Qualitätsüberwachung der Ausführung Products and systems for the protection and repair of concrete structures Definitions, Requirements, Quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works Certification scheme MPA-BS 031 ‚Construction adhesives‘ DIN EN 12004 2013-07 EN 12004 2007+A1:2012 Mörtel und Klebstoffe für Fliesen und Platten - Anforderungen, Konformitätsbewertung, Klassifizierung und Bezeichnung Adhesives for tiles - Requirements, evaluation of conformity, classification and designation DIN EN 15274 2015-06 EN 15274 2015 Klebstoffe für allgemeine Anwendungen in strukturellen Klebverbunden - Anforderungen und Prüfverfahren General purpose adhesives for structural assembly - Requirements and test methods Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 27/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 5 Certification of construction products (systems of assessment and verification of constancy of performance 1 and 1+) and factory production control (system 2+) in accordance with the Construction Products Regulation (EU) No 305/2011 to defined harmonised conditions for the marketing of construction products (Construction Products Regulation - CPR) Decision / System 1) Technical specification resolution of the Commission 1995/467/EC Gypsum products 1 1996/577/EC 2002/592/EC Fire alarm/detection, fixed fire-fighting, fire and smoke controland explosion suppression products 1 EN 13815:2006 Fibrous gypsum plaster casts - Definitions, requirements and test methods EAD 070001-00-0504 Gypsum plasterboard for load bearing applications EN 12101-1:2005+A1:2006 Smoke and heat control systems - Part 1: Specification for smoke barriers EN 12101-2:2003 Smoke and heat control systems - Part 2: Specification for natural smoke and heat exhaust ventilators EN 12101-03:2015 Smoke and heat control systems - Part 3: Specification for powered smoke and heat exhaust ventilators EN 12101-6:2005 Smoke and heat control systems - Part 6: Specification for pressure differential systems, Kits EN 12101-7:2011 Smoke and heat control systems - Part 7: Smoke duct sections EN 12101-8:2011 Smoke and heat control systems - Part 8: Smoke control dampers EN 15650:2010 Ventilation for buildings - Fire dampers 1996/590/EC Curtain wallings 1997/176/EC Structural timber products 1) 1 1 / 2+ EN 13830:2003 Curtain walling - Product standard EN 14250:2010 Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 28/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1 1997/176/EC Structural timber products 2+ 1997/462/EC Wood-based panels 1997/555/EC Cements, building limes and other hydraulic binders / Common cements 1997/556/EC External thermal insulation composite systems/kits with rendering 1997/740/EC Masonry and related products 1) 1 / 2+ 1+ 2+ 1 / 2+ 2+ EN 14080:2013 Glued laminated timber and glued solid timber Requirements EN 14081-1:2005+A1:2011 Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements EN 13986:2004+A1:2015 Wood-based panels for use in construction Characteristics, evaluation of conformity and marking EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements EN 459-1:2010 Building lime - Part 1: Definitions, specifications and conformity criteria ETAG 004:Version 08/2011 Guideline for European Technical Approval of external thermal insulation composite systems with rendering EN 771-1:2011 Specification for masonry units - Part 1: Clay masonry units EN 771-2:2011 Specification for masonry units - Part 2: Calcium silicate masonry units EN 771-3:2011 Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates) EN 771-4:2011 Specification for masonry units - Part 4: Autoclaved aerated concrete masonry units EN 771-5:2011 Specification for masonry units - Part 5: Manufactured stone masonry units EN 998-2:2010 Specification for mortar for masonry - Part 2: Masonry mortar System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 29/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1997/808/EC Floorings 1 1998/143/EC Systems of mechanically fastened flexible roof waterproofing membranes 2+ 1998/213/EC Internal partition kits 1 1998/214/EC Structural metallic products and ancillaries 2+ 1998/279/EC Non load bearing permanent shutterings: kits/systems 1 / 2+ based on hollow blocks or panels of insulating materials and,sometimes, concrete 1998/436/EC Roof coverings, rooflights, roof windows and ancillary 1 products (for uses subject to resistance to fire regulations) 1) 1998/437/EC Internal and external wall and ceiling finishes 1 1998/456/EC Post-tensioning kits for the prestressing of structures 1+ EN 13813:2002 Screed material and floor screeds - Screed materials Properties and requirements ETAG 006:2000 Guideline for European Technical Approval of systems of mechanically fastened flexible roof Waterproofing membranes ETAG 003:1999 Guideline for European Technical Approval of internal partition kits for use as non-loadbearing walls EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10088-5:2009 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes ETAG 009:2002 Guideline for European Technical Approval of non load-bearing permanent shuttering kits/systems based on hollow blocks or panels of insulating materials and sometimes concrete EN 490:2011 Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications EN 12467:2012 Fibre cement flat sheets - Product specification and test methods EN 13964:2014 Suspended ceilings - Requirements and test methods EN 14509:2013 Self-supporting double skin metal faced insulating panels - Factory made products - Specification EN 14716:2004 Stretched ceilings - Requirements and tests methods ETAG 013:2002 Guideline for European Technical Approval of post tensioning kits for prestressing of structures System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 30/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1998/598/EC 2002/592/EC Aggregates for uses with high safety requirements 2+ 1998/599/EC Kits for liquid applied roof waterproofing 1 1999/89/EC Prefabricated stair kits 1999/90/EC Waterproof sheeting - flexible sheeting for waterproofing steam barriers 1999/90/EC Waterproof sheeting roof sheeting 1) 2) 1 / 2+ 1 1 / 2+ EN 12620:2002+A1:2008 Aggregates for concrete EN 13055-1:2002+AC:2004 Lightweight aggregates - Part 1: Lightweight aggregates for concrete, mortar and grout EN 13139:2002+AC:2004 Aggregates for mortar ETAG 005:2005 Guideline for European Technical Approval of liquid applied roof waterproofing kit ETAG 008:2002 Guideline for European Technical Approval of prefabricated stair kits - Prefabricated stair kits in general (excluding severe climatic conditions) 2) EN 13859-1:2010 Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 1: Underlays for discontinuous roofing EN 13859-2:2010 Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 2: Underlays for walls EN 13970:2004+A1:2006 Flexible sheets for waterproofing - Bitumen water vapour control layers - Definitions and characteristics EN 13984:2013 Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics EN 13707:2004+A2:2009 Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics EN 13956:2012 Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics System for the assessment and verification of constancy of performance Excluding severe climatic conditions Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 31/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1999/90/EC Waterproof sheeting Barrier layers in buildings 1999/90/EC Waterproof sheeting Moisture barriers 1 / 2+ EN 13967:2012 Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics EN 13969:2004+A1:2006 Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - Definitions and characteristics 1 EN 14909:2012 Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics EN 14967:2006 Flexible sheets for waterproofing - Bitumen damp proof courses - Definitions and characteristics EN 13162:2012+A1:2015 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification EN 13163:2012+A1:2015 Thermal insulation products for buildings - Factory made products of expanded polystyrene (EPS) Specification 1999/91/EC Thermal insulation products 1 EN 13164:2012+A1:2015 Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) Specification EN 13165:2012+A1:2015 Thermal insulation products for buildings - Factory made rigid polyurethane foam (PUR) products Specification EN 13166:2012+A1:2015 Thermal insulation products for buildings - Factory made products of phenolic foam (PF) - Specification EN 13167:2012+A1:2015 Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification 1) System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 32/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission EN 13168:2012+A1:2015 Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification EN 13169:2012+A1:2015 Thermal insulation products for buildings - Factory made products of expanded perlite (EPB) – Specification EN 13170:2012+A1:2015 Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification EN 13171:2012+A1:2015 Thermal insulating products for buildings - Factory made wood fibre (WF) products - Specification EN 14303:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification 1999/91/EC Thermal insulation products 1 EN 14304:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification EN 14305:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification EN 14306:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification EN 14307:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification EN 14308:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification 1) System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 33/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission EN 14309:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification EN 14313:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification EN 14314:2009+A1:2013 Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification EN 14316-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loosefill products before installation 1999/91/EC Thermal insulation products 1 EN 14317-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation EN 14933:2007 Thermal insulation and light weight fill products for civil engineering applications - Factory made products of expanded polystyrene (EPS) - Specification EN 14934:2007 Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification EN 15599-1:2010 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation 1) System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 34/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1999/91/EC Thermal insulation products 1 1999/92/EC Light composite wood-based beams and columns 1 1999/93/EC Doors, windows, shutters, blinds, gates and related building hardware 1 1999/94/EC Precastnormal/lightweight/ autoclaved aerated concrete products 1) 2+ EN 15600-1:2010 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculite (EV) products Part 1: Specification for bonded and loose-fill products before installation ETAG 011:2011 Guideline for European Technical Approval of light composite wood-based beams and columns EN 14351-1:2006+A1:2010 Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian door sets without resistance to fire and/or smoke leakage characteristics EN 16034:2014 Pedestrian doorsets, industrial, commercial, garage doors and openable windows - Product standard, performance characteristics - Fire resistance and/or smoke control characteristics EN 1168:2005+A3:2011 Precast concrete products - Hollow core slabs EN 12737:2004+A1:2007 Precast concrete products - Floor slats for livestock EN 12794:2005+A1:2007+AC:2008 Precast concrete products - Foundation piles EN 12843:2004 Precast concrete products - Masts and poles EN 13224:2011 Precast concrete products - Ribbed floor elements EN 13225:2013 Precast concrete products - Linear structural elements EN 13693:2004+A1:2009 Precast concrete products - Special roof elements EN 13747:2005+A2:2010 Precast concrete products - Floor plates for floor systems EN 13978-1:2005 Precast concrete garages - Part 1: Requirements for reinforced garages monolithic or consisting of single sections with room dimensions EN 14843:2007 Precast concrete products - Stairs System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 35/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1) 1999/94/EC Precast normal/lightweight/ autoclaved aerated concrete products 2+ 1999/454/EC Fire stopping, fire sealing and fire protection products 1 EN 14844:2006+A2:2011 Precast concrete products - Box culverts EN 14991:2007 Precast concrete products - Foundation elements EN 14992:2007+A1:2012 Precast concrete products - Wall elements EN 15037-1:2008 Precast concrete products - Beam-and-block floor systems - Part 1: Beams EN 15037-2:2009+A1:2011 Precast concrete products - Beam-and-block floor systems - Part 2: Concrete blocks EN 15037-4:2010 Precast concrete products - Beam-and-block floor systems - Part 4: Expanded polystyrene blocks EN 15050:2007+A1:2012 Precast concrete products - Bridge elements EN 1520:2011 Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement EN 15258:2008 Precast concrete products - Retaining wall elements ETAG 018-1:2004 Guideline for European Technical Approval of fire protective products- Part 1: General ETAG 018-2:2006 Guideline for European Technical approval of fire protective products - Part 2: Reactive Coatings for Fire Protection of Steel Elements ETAG 018-3:2006 Guideline for European Technical Approval of fire protective products Part 3: Renderings and Rendering Kits intended for Fire Resisting Applications ETAG 018-4:2004 Guideline for European Technical Approval of fire protective products - Part 4: Fire protective board, slab and mat products and kits System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 36/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1999/454/EC Fire stopping, fire sealing and fire protection products 1999/455/EC Timber frame and log prefabricated building kits 1 1 ETAG 026-1:2008 Guideline for European Technical Approval of fire stopping and fire sealing products - Part 1: General ETAG 026-2:2008 Guideline for European Technical Approval of fire stopping and fire sealing products - Part 2: Penetration Seals ETAG 026-3:2008 Guideline for European Technical Approval of fire stopping and fire sealing products Part 3: Linear Joint and Gap Seals EAD 3500005-00-1104 Intumescent products for fire sealing ETAG 007:2001 Guideline for European Technical Approval of Timber Frame Building Kits EN 1504-2:2004 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete 1999/469/EC Products related to concrete, mortar and grout 1) 1 / 2+ EN 1504-3:2005 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 3: Structural and non-structural repair EN 1504-4:2004 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 4: Structural bonding EN 1504-5:2004 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 37/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 Decision / System 1) Technical specification resolution of the Commission 1999/469/EC Products related to concrete, mortar and grout 1 / 2+ 1999/469/EC Products related to concrete, mortar and grout 1 1999/470/EC Construction adhesives 2+ 2003/655/EC Watertight coverings kits for wetroom floors and walls 2011/284/EU Power, control and communication cables 1) 1 / 2+ 1+ EN 1504-6:2013 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 6: Anchoring of reinforcing steel bar EN 1504-7:2006 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 7: Reinforcement corrosion protection EN 14889-1:2006 Fibres for concrete - Part 1: Steel fibres - Definitions, specifications and conformity EN 14889-2:2006 Fibres for concrete - Part 2: Polymer fibres Definitions, specifications and conformity ETAG 012:2002 Guideline for European Technical Approval of Log Building Kits EN 15274:2015 General purpose adhesives for structural assembly Requirements and test methods ETAG 022-1:2007 Guideline for European technical approval of watertight covering kits for wet room floors and/or walls - Part 1: Liquid applied coverings with or without wearing surface ETAG 022-2:2011 Guideline for European Technical Approval of watertight covering kits for wet room floors and/or walls - Part 2: Kits based on flexible sheets ETAG 022-3:2011 Guideline for European Technical Approval of watertight covering kits for wet room floors and/or walls - Part 3: Kits based on inherently watertight boards EN 50575:2014 Power, control and communication cables - Cables for general applications in construction works subject to reaction to fire requirements System for the assessment and verification of constancy of performance Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 38/39 Annex to the Accreditation Certificate D-ZE-11267-01-00 The requirements for a certification body for products and for a certification body for factory production control according to Annex V of the Construction Products Regulation are fulfilled according to article 43 of the Construction Products Regulation. Required tasks which the holder of the certificate cannot perform are described in the list of subcontractors. Without prior approval by the DAkkS German Accreditation Body, the certification body is permitted to use new revisions of product standards in certification schemes. Without prior approval by the DAkkS German Accreditation Body, the certification body is permitted to use certification schemes of the following product groups to new products within the product family. Masonry and related products Building bricks category I in walls, columns and partions System 2+ Aggregates for uses with high safety requirements Aggregates System 2+ Precast normal,lightweight and autoclaved aerated concrete products for loadbearing apllications Group A and Group B System 2+ Abbreviations used: AGI ASTM DIN EN ETA ETAG ISO MPA-BS xxx prEN Q Arbeitsgemeinschaft Industriebau (Industrial Construction Working Group) American Society for Testing and Materials Deutsches Institut für Normung e. V. (the German Institute for Standardization) Europäische Standard European Technical Approval Guideline for European Technical Approval International Standardization Organization Certification scheme of the MPA Braunschweig Draft of a European standard Spreadsheets of the Arbeitsgemeinschaft Industriebau (AGI), row Q Period of validity: 06.06.2016 to 01.11.2017 Date of issue: 01.08.2016 - Translation - 39/39