Zwiebel- und Gemüsehacker Onion and Vegetable Chopper
Transcrição
Zwiebel- und Gemüsehacker Onion and Vegetable Chopper
Zwiebel- und Gemüsehacker Onion and Vegetable Chopper Hachoir à oignons et légumes Uien-groentehakker Tritaverdure D > geeignet zum Zerkleinern von Zwiebeln, Kräutern, Schokolade, Nüssen und vielem mehr > ergonomisch geformter Druckknopf für angenehmes und kraftschonendes Arbeiten > automatische Rotation der Messer für schnelles und effektives Schneideergebnis > einfache Reinigung GB > ideal for chopping onions, herbs, chocolates, nuts and many other foodstuffs > ergonomic press knob for convenient and effortless functionality > automatic rotating blade assembly for quick and efficient cutting results > easy to clean F > Pour hacher les oignons, les fines herbes, le chocolat, les noix, les légumes … > Forme ergonomique du bouton poussoir pour un travail agréable demandant peu d’efforts > Rotation automatique du couteau pour un travail rapide et efficace > Nettoyage et entretien faciles ART. NR. 16271 Sehr geehrter RÖSLE-Kunde, vielen Dank, dass Sie sich für einen hochwertigen Zwiebel- und Gemüsehacker aus unserem Hause entschieden haben. Eine gute Wahl. Und eine Entscheidung für ein langlebiges Qualitätsprodukt. Um Ihnen über viele Jahre Freude zu bereiten, haben wir für Sie die wichtigsten Punkte zum Aufbau, optimalen Nutzung, Pflege und Sicherheitshinweise zusammengestellt. Bitte lesen Sie unbedingt die Bedienungsanleitung vor dem ersten Einsatz. Ihr RÖSLE Zwiebel- und Gemüsehacker besteht aus lediglich 4 Bausteinen (siehe Abbildung): 4 3 2 1 2 3 4 Hackteller Transparentes Kunststoffgehäuse Messerführung Oberteil mit Schneiden am unteren Ende und einem Stößel am oberen Ende 1 Inbetriebnahme Wir empfehlen vor der ersten Nutzung eine Reinigung. Dazu bauen Sie den Zwiebel- und Gemüsehacker mit einigen wenigen Handgriffen auseinander. Folgende Schritte sind dazu erforderlich. Bitte beachten Sie, dass es sich um ein Schneidgerät handelt und es bei unsachgemäßem Gebrauch zu Verletzungen kommen kann. Demontage 1. Zwiebelhacker mit dem Teller auf die Arbeitsplatte stellen. 2. Das Kunststoffgehäuse festhalten und das Oberteil gegen den Uhrzeigersinn bis zum Anschlag drehen. Anschließend nach oben abnehmen. 3. Drehen Sie das Oberteil mit den Messern nach oben. ACHTUNG: Bitte beachten Sie, dass die Messer geschärft sind und einen sorgfältigen Umgang erfordern (Verletzungsgefahr). Messerführung vorsichtig aus dem Oberteil entnehmen. 4. Transparentes Kunststoffgehäuse vom Teller abnehmen. Reinigung Nach der Demontage des Zwiebel- und Gemüsehackers können Sie alle Teile reinigen. Wir empfehlen die Reinigung mit einer geeigneten Bürste unter fließendem Wasser. Bei Bedarf verwenden Sie zusätzlich Reinigungsmittel. Das Oberteil mit den Schneiden säubern Sie mit einer Spülbürste und geeignetem Reinigungsmittel, alle anderen Teile wie Hackteller, Messerführung und Kunststoffgehäuse sind in der Spülmaschine reinigbar. Nach der Reinigung sollte das Oberteil zum Trocknen auf die Schneiden gestellt werden. Bitte die Messer des Zwiebel- und Gemüsehackers nicht manuell mit einem Trockentuch trocknen, da sonst erhöhte Verletzungsgefahr besteht. Zusammenbau Nach der Reinigung können Sie die Einzelteile einfach wieder zusammensetzen. Folgende Schritte sind dazu erforderlich. 1. Den Teller mit der Öffnung nach oben auf die Arbeitsplatte legen. 2. Das transparente Kunststoffgehäuse mit dem kleineren Durchmesser nach unten in den auf der Arbeitsplatte liegenden Teller einstecken. 3. Das Oberteil mit den Messern nach oben halten. ACHTUNG: Bitte beachten Sie, dass die Messer geschärft sind und einen sorgfältigen Umgang erfordern (Verletzungsgefahr). Halten Sie daher die Messerführung nur außen und nicht im Bereich der Klingenaussparungen. Stecken Sie die Messerführung mit dem Abstreifer nach oben über die Messer in das Oberteil bis sie eingerastet ist. (Bitte beachten: zum einfacheren Aufsetzen erst den Bereich der Klingenaussparungen passend zum Messer ausrichten.) 4. Das Oberteil mit der aufgesteckten Messerführung in das transparente Kunststoffgehäuse einsetzen. Nun im Uhrzeigersinn drehen bis das Oberteil in die Aussparungen des Kunststoffgehäuses hineingleitet. Jetzt das Kunststoffgehäuse festhalten und das Oberteil bis zum Anschlag drehen. Jetzt ist der Zwiebel- und Gemüsehacker einsatzbereit. Verwendung 1. Den Teller abnehmen, Zwiebel oder Gemüse auf den Teller legen und Oberteil wieder aufsetzen. 2. Den kompletten Küchenhelfer gerade auf den Tisch bzw. Arbeitsplatte stellen. 3. Mit einer Hand das Gerät festhalten und mit der zweiten Hand gleichmäßig von oben drücken. 4. Der Rückzug des Schneidwerks funktioniert automatisch durch eine integrierte Feder. 5. Während des Rückzuges drehen sich die Messer um 60 Grad weiter. 6. Der Abstreifer löst zusätzlich Zwiebel- und Gemüsereste von der Gehäuseoberfläche. Hinweis: Bei größeren Mengen können Sie anstelle des Tellers auch ein adäquates Schneidbrett benutzen, auf dem Sie die passenden Portionen aufteilen können. RÖSLE empfiehlt das runde Kunststoff-Schneidbrett mit der Artikelnummer 15072. Bitte prüfen Sie, ob andere vorgesehene Unterlagen für den Einsatz geeignet sind. Sie verhindern dadurch mögliche Folgeschäden am Küchenhelfer bzw. der Unterlage. Um eine schnelle und effiziente Reinigung zu erzielen, empfehlen wir unmittelbar nach der Verwendung die Messer zu reinigen. Allgemeine Sicherheitshinweise Der Zwiebel- und Gemüsehacker ist kein Spielzeug und ist mit der notwendigen Sorgfalt zu behandeln. Bitte von Kindern fernhalten. Viel Spaß mit Ihrem neuen Küchenhelfer, der Sie beim Vor- und Zubereiten Ihrer nächsten Rezepte begleitet und unterstützt. Ihr RÖSLE-Team Dear RÖSLE Customers, Thank you for choosing a quality Onion and Vegetable Chopper from our production line. It is a clever choice and the utensil will serve you well for a long time. We draw your attention here to some important aspects for its’ assembly, optimal use and aftercare plus some safety guidelines. Please read these instructions before first use. Your RÖSLE Onion and Vegetable Chopper is comprised of 4 components (see illustration): 4 3 1 2 3 4 Chopping tray Transparent synthetic cover Blade guide Upper assembly housing blades below and press knob on top 2 1 First time use Cleaning is recommended before first time use. For this purpose, please follow the procedure provided below for disassembling the Onion and Vegetable Chopper in a few simple steps. Please remember, you are dealing with a cutting instrument and correct handling is required to avoid injury. Disassembling 1. Stand the Onion and Vegetable Chopper on its chopping tray on a flat surface. 2. Firmly grip the transparent synthetic cover and turn the upper assembly counterclockwise until finished. Lift out the upper assembly. 3. Turn the upper assembly upside down so that the blades point upward. NOTE: Please remember that the blades are sharp and should be handled with caution to avoid injury. Carefully remove the blade guide from the upper assembly. 4. Separate the transparent synthetic cover from the chopping tray. Cleaning Once disassembled, all components of the Onion and Vegetable Chopper can be cleaned. We recommend use of an appropriate brush under running water. Common liquid soap may be used to clean if necessary. The upper assembly with the blades should be cleaned with liquid soap and a brush. All other parts i.e. the chopping tray, blade guide and transparent synthetic cover can go into the dishwasher for cleaning. After cleaning, the upper assembly should be placed upright on the blades for drying. Please do not attempt to dry the blades by hand with a kitchen towel because of risk of injury. Assembling After cleaning the individual parts must be reassembled. Please follow these steps described below. 1. Place the chopping tray on a flat surface with its aperture upwards. 2. Insert the narrow end of the transparent synthetic cover into the chopping tray. 3. Hold the upper assembly with the blades pointing upward. NOTE: Please remember that the blades are sharp and need to be handled with caution to avoid injury, so when handling the blade guide, hold it at its extremity avoiding contact with the blade grooves. Slide the blade guide over the blades in the upper assembly with the wiper pointing upwards until it clicks into position. (Please note: For easy fitting, make sure to first align the blade grooves with the blade). 4. Put the upper assembly with the fitted blade guide into the transparent synthetic cover. Turn clockwise so that the upper assembly slides into the guiding grooves in the cover. Firmly grip the transparent synthetic cover and turn the upper assembly until it locks into place. The Onion and Vegetable Chopper is now ready for use. Use 1. Remove the chopping tray, place onions or vegetables on it and replace the upper assembly. 2. Place the complete utensil upright on a flat surface i.e. kitchen table. 3. Hold the utensil with one hand and use the other to press downward on the knob. 4. The blades retract automatically powered by spring tension. 5. During the retraction movement the blades will turn 60°. 6. The wiper is designed to remove onion or vegetable remnants from the cover surface. Note: For larger quantities, the chopping tray can be replaced with a more adequate chopping board of appropriate portions. RÖSLE recommends the round Chopping Board – Art.-No. 15072. If using other chopping surfaces please check their suitability so as to prevent damage to the utensil or chopping board. For quick and efficient cleaning, blades should be cleaned soon after use. General safety guidelines The Onion and Vegetable Chopper should not be used as a toy and should be handled with caution. Please keep the utensil out of the reach of children. We hope you enjoy the use of this new kitchen friend which will help you in preparing new and delicious culinary treats. Your RÖSLE Team Cher Client RÖSLE Nous vous remercions d’avoir choisi un Hachoir RÖSLE haut de gamme. Le choix d’un produit de qualité. En suivant les quelques conseils d’utilisation, d’entretien et de sécurité suivants, il vous donnera entière satisfaction pendant de longues années. Avant la première utilisation, veuillez lire attentivement les conseils d’utilisation suivants. Votre Hachoir à oignons et légumes RÖSLE est composé de 4 éléments (voir dessin) 4 3 2 1 Soucoupe 2 Fourreau eu plastique transparent 3 Protection du couteau 4 Corps du Hachoir avec couteau et bouton pressoir 1 Mise en service Avant la première utilisation nous vous recommandons de nettoyer le hachoir. Pour cela il suffit de le démonter hachoir. Merci de suivre les étapes indiquées ci-dessous. Attention : il s’agit d’un ustensile coupant qui peut engendrer des blessures par inattention. Démontage 1. Posez le Hachoir avec la soucoupe sur le plan de travail 2. Tenez le fourreau en plastique transparent et tournez dans le sens inverse des aiguilles d’une montre jusqu’à ce qu’il résiste. Ensuite tirez vers le haut. 3. Retournez le corps avec le couteau vers le haut. Attention : les couteaux sont affûtés et doivent être manipulés avec précaution (risque de coupure). Retirez avec prudence la protection du couteau. 4. Retirer le fourreau en plastique de la soucoupe. Nettoyage Après le démontage du Hachoir à oignons et légumes vous pouvez nettoyer tous les éléments. Nous recommandons le nettoyage à l’eau courante avec une brosse à vaisselle. Si besoin est, ajoutez du produit à vaisselle. Le corps avec le couteau et le bouton est à nettoyer à la main avec une brosse. Tous les autres éléments comme la soucoupe, la protection du couteau et le fourreau en plastique peuvent être nettoyés au lave-vaisselle. Après avoir nettoyé le corps du Hachoir, posez celui-ci sur le couteau pour qu’il sèche. Evitez d’essuyer le couteau du Hachoir avec un torchon pour ne pas vous blesser. Assemblage Après le nettoyage il suffit d’assembler les éléments comme suit : 1. Posez la soucoupe sur le plan de travail 2. Insérez le fourreau en plastique transparent avec le plus petit diamètre dans la soucoupe. 3. Tenez le corps avec le couteau vers le haut. Attention : les couteaux sont affûtés et doivent être manipulés avec précaution (risque de coupure). C’est pourquoi vous devez maintenir la protection du couteau sur les bords et non pas sur la partie avec les fentes. Emboîtez la protection (la languette noire se trouve vers le haut), faites attention à ce que le couteau soit en face des fentes et poussez la protection vers le bas jusqu’à ce qu’elle clique. 4. Mettez le corps du hachoir dans le fourreau en plastique transparent. Tournez dans le sens des aiguilles d’une montre jusqu’à ce que le corps du hachoir s’encastre dans le système à baïonnette du fourreau et ensuite résiste. Votre Hachoir à oignons et légumes RÖSLE est maintenant prêt à l’emploi. Utilisation 1. Enlevez la soucoupe, posez les oignons ou légumes sur la soucoupe et remettez le Hachoir sur la soucoupe. 2. Posez le Hachoir à plat sur la table ou un plan de travail. 3. Tenez d’une main le Hachoir et de l’autre poussez sur le bouton. 4. Le bouton remonte automatiquement vers le haut grâce à un système de ressort. 5. Le couteau prend à chaque pression un nouvel angle (60°). 6. La languette racle le bord du fourreau en plastique pour détacher les morceaux d’oignons ou de légumes. Conseil: Pour de plus grandes quantités, vous pouvez utiliser une planche à découper au lieu de la soucoupe, sur laquelle vous pouvez répartir les aliments à hacher en portions. RÖSLE recommande la planche à découper ronde en polyéthylène (art. n° 15072). Si vous utilisez d’autres supports, veillez à ce qu’ils soient adaptés au Hachoir afin d’éviter tout risque de dommages. Afin de nettoyer rapidement et efficacement le Hachoir, nous vous recommandons de nettoyer le couteau directement après utilisation. Recommandations générales de sécurité. Le hachoir à oignons et légumes n’est pas un jouet et doit être utilisé avec précaution. Veuillez le tenir hors de la portée des enfants. Nous vous souhaitons beaucoup de plaisir avec votre nouvel ustensile de cuisine qui vous accompagnera et vous facilitera la tâche lors de vos prochaines préparations culinaires. Votre équipe RÖSLE 08/06 RÖSLE GmbH & Co. KG Johann-Georg-Fendt-Straße 38 | D-87616 Marktoberdorf Telefon +49 8342 912 0 | Telefax +49 8342 912 190 | www.roesle.de