Excite F5D

STRATAIR - Modelltechnik GmbH, Stierberg 11, A-4153 Peilstein
Excite F5D
Thank you for choosing the Excite F5D, one of our
high performance models.
The Excite F5D is the result of a lot competition
experience and developing. Out of the kit you will be
able to win F5D contests. With the three different removable noses you can use direct drive motors or geardrives or use the
Excite F5D as a glider. The model is also usable for extreme DS (dynamic soaring). The wing is produced out of full carbon
and the fuse out of aramid with unidirectional carbon. The is nearly ready to fly. Never the less we recommend to read the
instruction very carefully.
ATTENTION:
The Excite F5D can reach extreme high speeds. Be aware that this is not just a toy! It is a toy for big boys
Finally STRATAIR wishes you a lot of fun in building and flying the Excite F5D
1. Fuselage:
Pushrod for elevator: take some 0,8mm steel wire and connect it to the servohorn. Move the servo incl. 0,8mm steel into the
fuse just behind end of wing. Now cut the steel wire 2cm after top-end of vertical stabilizer. Take a plastic tube (1mm inner
diameter), cut it 8cm shorter than the steel wire and put it together. Glue a rudder horn into the elevator. Move the servo now
again into the fuse and glue it. Then bend the steel wire to 90 degrees exactelly at the hole of the rudder horn. The rudder horn
can be connected to the steel wire. Check neutral position of the servo. It is important that you fix the plastic tube with the fuse.
Otherwise there will be tolerance in the elevator. Reveiver and receiver-accu should be placed also behind the wing or as far as
possible in the aft section.
Depending on motorweight use long or short nose. For the glidernose you need some weight in the front.
3. Wing:
With a knife cut out of the wing the servocover. Install the servocables and glue the servo into the wing. Best is when the servo
has contact to upper and bottom side of the wing. Glue the rudder horn in the aileron and make the pushrod to the servo. For the
servolever some openings are necessary.
4. General:
If there is some tolerance on elevator or aileron trop some second glue between rudder connector and steel wire. Let it harden.
Thereafter “brake” the glueing via moving the steel wire.
5. Movements:
Elevator: + 3/–2mm
Aileron: +7/–5mm
CQ: 40-45mm behind leadingedge
Recommended components:
Motor:
Accu:
Receiver:
Servos:
From 100g-200g brushless, or also Speed 600
7xGP3300 or 3S Lipos
MZK QUATRA, Schulze receivers, a.s.o.
DYMOND D60 or D47
STRATAIR- Modelltechnik GmbH, Stierberg 11, A-4153 Peilstein,
Tel: +43(699)11041848, Tel/Fax.: +43(2169)27141, E-Mail: [email protected], Internet: www.strat.at, UID-Nr.: ATU 612 284 88, FN : 253148 b, SteuerNr. : 143/4787
Pylon F5D-Setup:
1: WM Set Up 2006
Mega 16/25/2
Castle Creations Phönix 60 oder 80
18x GP 1300 oder 5S ca. 1800 mAh Lipo
Cam Speed 4,7x4,7
Motor
Regler
Akku
Prop
2: Mittlere Leistungsklasse – moderate power
Mega 16/25/2
Castle Creations Phönix 80
4S ca. 2400 mAh Lipo
Cam Speed 5,2x5,2
Motor
Regler
Akku
Prop
3: Mittlere Leistungsklasse – moderate power
Mega 16/25/2
Castle Creations Phönix 80
3S ca. 3200 mAh Lipo
Speed Prop 7x7
Motor
Regler
Akku
Prop
4: Hohe Leistung/geringere Drehzahl – high power/“low“ rpm
Mega 16/35/1
Motor
Kontronik Jazz Fai 18
Regler
3S ca. 3200 mAh Lipo
Akku
Cam Speed 6x6 / 5,5x5,5
Prop
Wettbewerb Set-Up 2008 mit ca. 800 Watt
5: Hohe Leistung/hohe Drehzahl – high power/“high“ rpms
Mega 16/35/1
Motor
Kontronik Jazz Fai 18
Regler
4S ca. 2400 mAh Lipo
Akku
Cam Speed 4,7x4,7
Prop
Extrem Laut- Sehr hohe Drehzahl- sehr hohe Leistung- Akku sehr am Limit (kokam 2400 30C)
Very loud – very high rpms – very high power – battery on limit (kokam 2400 30C)
STRATAIR- Modelltechnik GmbH, Stierberg 11, A-4153 Peilstein,
Tel: +43(699)11041848, Tel/Fax.: +43(2169)27141, E-Mail: [email protected], Internet: www.strat.at, UID-Nr.: ATU 612 284 88, FN : 253148 b, SteuerNr. : 143/4787
Hotliner Set-Up für F5D Modelle:
1: Sehr gute Leistung und Lebendauer – v.good power and lifetime
16/25/1 mit 5,2:1 KPG Getriebe
CC Phönix 80
RFM 12,8x13 Prop
3S Lipo ab 3200 mAh
Strom: 100A = ca. 1KW
2: Sehr, sehr gute Leistung/gute Lebensdauer + v.v.good power and lifetime
16/25/1 mit 5,2:1 KPG Getriebe
CC Phönix 80
RFM 14,5x14 Prop
3S Lipo ab 3200 mAh
Strom: 150A = ca. 1,5 KW
3: Ultimative Leistung/begrenzte Lebensdauer vom Akku – ultimative power/limited battery lifetime
Motor, Getriebe und Regler halten das gut aus. Kühlung sehr wichtig.
Motor, gearbox and ESC OK fort hat power but cooling is important
16/25/1 mit 4,2:1 KPG Getriebe
Jazz FAI 18
RFM 14,5x14 Prop
3S Lipo ab 3200 mAh ab 30 C
Strom: 240A = ca. 2,4KW
Steigleistung bei Excite ca. 90 m/s
STRATAIR- Modelltechnik GmbH, Stierberg 11, A-4153 Peilstein,
Tel: +43(699)11041848, Tel/Fax.: +43(2169)27141, E-Mail: [email protected], Internet: www.strat.at, UID-Nr.: ATU 612 284 88, FN : 253148 b, SteuerNr. : 143/4787